Epson 8300NL - PowerLite XGA LCD Projector User manual

EPSON®PowerLite®8300i
Multimedia Projector
User’sGuide

2
Important Safety Information
WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes.
Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and
filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically
explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service
personnel.
WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small
children to avoid any risk of suffocation.
Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by
the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for
use with this EPSON product. EPSON is not responsible for any use of this information as applied to other
products.
Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third
parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse,
or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with SEIKO EPSON CORPORATION’s operating and maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising from the use of any
options or any consumable products other than those designated as Original EPSON Products or EPSON
Approved Products by SEIKO EPSON CORPORATION.
EPSON is a registered trademark, and EasyMP and Quick Corner are trademarks of SEIKO EPSON
CORPORATION.
EPSON Connection, EPSON Store, and Extra Care, are service marks; EasyManagement and SizeWise are
trademarks; and PrivateLine, Presenters Club, and PowerLite are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. EPSON disclaims any and all rights in those marks.
© 2005 by Epson America, Inc. 10/05
CPD-16107R5

3
Contents
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Getting More Information . . . . . . . . . . . . . . . . . . . . . . . . 8
Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Additional Components. . . . . . . . . . . . . . . . . . . . . . . . . 11
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1Setting Up the Projector . . . . . . . . . . . . . . . . . . . . . 13
Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connecting to Video Equipment . . . . . . . . . . . . . . . . . . . . . 16
Connecting a Composite Video Source . . . . . . . . . . . . . 17
Connecting an S-video Source . . . . . . . . . . . . . . . . . . . . 18
Connecting a Component Video Source . . . . . . . . . . . . 19
Connecting an RGB Video Source. . . . . . . . . . . . . . . . . 20
Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . 22
Connecting to the Computer 1 or 2 Port . . . . . . . . . . . . 23
Connecting to the BNC Port . . . . . . . . . . . . . . . . . . . . . 24
Connecting to the DVI Port . . . . . . . . . . . . . . . . . . . . . 25
Using the Macintosh Desktop Adapter . . . . . . . . . . . . . 26
Connecting the Cable for Remote Mouse Control . . . . 27
Connecting an External Monitor . . . . . . . . . . . . . . . . . . . . . 28
Playing Sound Through the Projector. . . . . . . . . . . . . . . . . . 29
Connecting Audio Equipment to the Projector . . . . . . . 29
Connecting External Speakers . . . . . . . . . . . . . . . . . . . . 30

4
2Displaying and Adjusting the Image . . . . . . . . 31
Projecting the Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Turning on the Projector . . . . . . . . . . . . . . . . . . . . . . . . 32
Selecting the Image Source. . . . . . . . . . . . . . . . . . . . . . . 34
Troubleshooting Display Problems. . . . . . . . . . . . . . . . . . . . 35
You Can’t Project an Image . . . . . . . . . . . . . . . . . . . . . . 35
The Projector and Laptop
Don’t Display the Same Image . . . . . . . . . . . . . . . . 35
Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Focusing and Zooming Your Image. . . . . . . . . . . . . . . . 38
Adjusting the Height of Your Image . . . . . . . . . . . . . . . 39
Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 40
Correcting Computer Images. . . . . . . . . . . . . . . . . . . . . 42
Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . . . . 43
3Giving Your Presentation . . . . . . . . . . . . . . . . . . . 45
Activating and Using the Remote Control . . . . . . . . . . . . . . 46
Using the Navigation Buttons . . . . . . . . . . . . . . . . . . . . 47
Controlling Multiple Projectors. . . . . . . . . . . . . . . . . . . 48
Replacing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . 50
Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 51
Switching Between Picture Sources . . . . . . . . . . . . . . . . 51
Previewing Picture Sources . . . . . . . . . . . . . . . . . . . . . . 52
Turning Off the Picture and Sound . . . . . . . . . . . . . . . 53
Stopping Action. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Zooming Your Image. . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Displaying a Picture-in-Picture Video . . . . . . . . . . . . . . 54
Adjusting the Brightness . . . . . . . . . . . . . . . . . . . . . . . . 55
Controlling the Volume. . . . . . . . . . . . . . . . . . . . . . . . . 55
Highlighting Your Presentation . . . . . . . . . . . . . . . . . . . . . . 56
Using the Pointer Tool . . . . . . . . . . . . . . . . . . . . . . . . . 56
Customizing the Pointer Tools . . . . . . . . . . . . . . . . . . . 57
Operating Your Computer with the Remote Control . . . . . 58
Creating Your Own Startup Screen . . . . . . . . . . . . . . . . . . . 59
Capturing the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Choosing When to Display the Image . . . . . . . . . . . . . . 60

5
4Fine-tuning the Projector. . . . . . . . . . . . . . . . . . . . 61
Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . 63
Adjusting the Image Quality. . . . . . . . . . . . . . . . . . . . . . . . . 64
Adjusting Computer Images. . . . . . . . . . . . . . . . . . . . . . 65
Adjusting the Image Size, Shape, and Position . . . . . . . . . . . 67
Adjusting the Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Adjusting the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 70
Image Setup Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Communication Setup Options . . . . . . . . . . . . . . . . . . . 71
Miscellaneous Setup Options . . . . . . . . . . . . . . . . . . . . . 72
5Managing the Projector
from a Remote Computer. . . . . . . . . . . . . . . . . . . . 73
Installing the EasyManagement Software . . . . . . . . . . . . . . . 74
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Installing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Connecting and Configuring the Projector. . . . . . . . . . . . . . 76
Using EMP Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Opening and Closing EMP Monitor . . . . . . . . . . . . . . . 78
Registering a Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Monitoring Your Projectors . . . . . . . . . . . . . . . . . . . . . . 80
Controlling Your Projectors . . . . . . . . . . . . . . . . . . . . . . 82
Configuring the Monitoring Interval . . . . . . . . . . . . . . . 83
Using EMP NetworkManager . . . . . . . . . . . . . . . . . . . . . . . 84
Selecting the Projectors to Monitor . . . . . . . . . . . . . . . . 84
Creating the E-Mail Settings . . . . . . . . . . . . . . . . . . . . . 86
Understanding the Notification Messages . . . . . . . . . . . 88
6Maintaining the Projector. . . . . . . . . . . . . . . . . . . 89
Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . 90

6
Cleaning and Replacing the Filters . . . . . . . . . . . . . . . . . . . . 91
Cleaning the Lamp Filter . . . . . . . . . . . . . . . . . . . . . . . . 91
Cleaning the Air Intake Filters . . . . . . . . . . . . . . . . . . . . 92
Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . 96
Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 97
7Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Checking the Projector Status. . . . . . . . . . . . . . . . . . . . . . . 100
What To Do When the Lights Flash . . . . . . . . . . . . . . 100
Viewing the ‘About’ Menu Screen . . . . . . . . . . . . . . . . 103
Solving Problems with the Image or Sound . . . . . . . . . . . . 104
Solving Problems with the Remote Control . . . . . . . . . . . . 109
Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Telephone Support Services . . . . . . . . . . . . . . . . . . . . . 110
Appendix A: Projector Installation . . . . . . . . . 111
Placement and Mounting Guidelines . . . . . . . . . . . . . . . . . 111
Image Size and Projection Distance . . . . . . . . . . . . . . . . . . 112
Image Size Calculations (For All Lenses) . . . . . . . . . . . 113
Converting Between Diagonal Size
and Width or Height. . . . . . . . . . . . . . . . . . . . . . . 115
Converting Between 16:9 and 4:3 Image Sizes. . . . . . . 115
Installing the Rear Cable Cover . . . . . . . . . . . . . . . . . . . . . 116
Installing Multiple Projectors . . . . . . . . . . . . . . . . . . . . . . . 116
Appendix B: Technical Specifications . . . . . . 117
Appendix C: Notices. . . . . . . . . . . . . . . . . . . . . . . . 123
Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . 123
Remote Control Information . . . . . . . . . . . . . . . . . . . . . . . 125
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . 126
FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 127
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Welcome 7
-
Welcome
The EPSON® PowerLite®8300i is a theater-grade projector that
offers up to 5200 ANSI lumens of brightness. Images are displayed at
a resolution of 1024 ×768 pixels, and the 1.4-inch LCD provides an
unprecedented 1200:1 contrast ratio (1500:1 in low-brightness mode)
for incredibly rich images. From auditoriums to conference rooms,
your full-color presentations will be vivid and clear even in bright
indoor environments.
Your projector includes these outstanding features:
■Connectivity
Your EPSON PowerLite projector can be connected to four
computer sources and five video sources (up to a total of six
sources at the same time). You can include an independent sound
channel for each of the six sources. A preview feature lets you see
all the sources at a glance, so you can easily switch between them.
■Complete control
Use the remote control to take charge of your presentation. Freeze
the action, zoom in on part of the picture, or display a
picture-in-picture video. Use the remote as a pointer, or to draw
on the screen. You can even use it in place of your computer’s
mouse to control your computer and change slides in
PowerPoint.
®
■EasyManagement
With the projector’s EasyManagement™system, you can use a
Windows®PC to remotely monitor and control the projector.
■EasyMP.net™ (optional; see page 12)
The optional EasyMP.net offers you a premium network solution:
web browsing, remote desktop client access, projection over an
802.11b wireless network, and storage of Microsoft®PowerPoint
slideshows on a memory card for computer-free presentations.

8Welcome
Using Your Documentation
This book contains all the information you need to set up and use
your projector. Please follow these guidelines as you read through it:
■Warnings must be followed carefully to avoid bodily injury.
■Cautions must be observed to avoid damage to your equipment.
■Notes contain important information about your projector.
Getting More Information
Need tips on giving presentations? Quick steps for setting up your
projector? Here’s where you can look for help:
■presentersonline.com
Includes a library of articles covering presentation tips, tricks, and
technology. The site provides templates, clip art and sound clips,
as well as Presenters Services to use on the road. Even more
resources and services are available if you register to join the
Presenters Club®—and it’s free.
■Quick Setup sheet
Gives you basic instructions on connecting to a laptop.
■Start Here kit
Includes this User’s Guide, your Quick Setup sheet, warranty
brochures, and EPSON PrivateLine®Support card. Keep the
folder with your projector at all times.
■Built-in help system
Provides assistance for common problems. Available from the
Help button on the projector or the remote control.
■support.epson.com
Download FAQs and e-mail your questions to EPSON support.
need help?
If you still need help after
checking this User’s Guide
and the sources listed here,
you can use the EPSON
PrivateLine Support service
to get help fast. Call (800)
637-7661 and enter the
PIN on the card in your
Start Here kit. Or take
advantage of EPSON’s
automated support services
24 hours a day. See
page 110 for more
information.

Welcome 9
Registration and Warranty
Your projector comes with a basic carry-in warranty as well as an
international warranty that let you project with confidence anywhere
in the world. For details, see page 128 and the warranty brochure
included in your Start Here kit.
In addition, for customers who register their projector, EPSON offers
free Extra CareSM Road Service. In the unlikely event of an equipment
failure, you won’t have to wait for your unit to be repaired. Instead,
EPSON will ship you a replacement unit anywhere in the United
States or Canada, usually via overnight delivery. See the brochure in
your Start Here kit for details.
To register, simply fill out the registration card included in your Start
Here kit and mail it to EPSON. Or you can register online at
http://epsonwebreg.info2.net/. Registering also lets you receive special
updates on new accessories, products, and service.

10 Welcome
Unpacking the Projector
After unpacking the projector, make sure you have all the parts shown
below:
Save all packaging in case you need to ship the projector. Always use
the original packaging (or the equivalent) when you need to send the
projector to another location.
Projector* Rear cable cover Projector software
CD-ROM
Remote control AA batteries Power cord
Computer VGA cable Audio (stereo
mini-jack) cable
USB cable
* Remove plastic film from projector’s control panel.

Welcome 11
Additional Components
The projector comes with the cables you need for most computer or
laptop setups. Depending on how you plan to use the projector, you
may need additional components:
■To connect to a video player, you may need one of these cables:
■RCA video cable
■S-video cable
■BNC cable
These cables are usually included with your video player; check
the appropriate section in Chapter 1 to make sure of the kind of
cable you need. You may be able to purchase it from EPSON (see
page 12) or from your video dealer.
■To receive stereo sound from a video player, you’ll need a
dual-RCA cable, available from most electronics dealers.
■To connect a computer to the projector’s Digital Video Interface
(DVI) port, you’ll need a DVI-D dual-link digital video cable,
available from EPSON (see page 12); an optional DVI to DFP
cable is also available.
■Some older PowerBooks and Macintosh desktop models may
need a video-out cable (provided by Apple®) or the Macintosh
adapter set shown on page 26 (available from EPSON; see
page 12). Older iMac systems may need a special adapter to
provide a VGA output port; see your computer dealer.

12 Welcome
Optional Accessories
To enhance your use of the projector, EPSON provides the following
optional accessories:
You can purchase these accessories from your dealer, by calling
EPSON at [phone], or by visiting the EPSON StoreSM at
www.epsonstore.com (U.S. sales only). In Canada, please call
[phone] for dealer referral.
Product Product no.
Replacement lamp and air filter V13H010L23
Air filter set V13H134A02
EasyMP.net network option board V12H114P01
Mounting hardware:
Ceiling mount
Suspension adapter
False ceiling plate
ELPMB41
ELPMBAPL
ELPMBFCP
Projection screens:
50-inch portable screen
60-inch portable pop-up screen
80-inch portable pop-up screen
ELPSC06
ELPSC07
ELPSC08
Lenses:
Rear-projection wide lens
Wide zoom lens
Standard zoom lens
Middle throw zoom lens (2.42 to 3.67:1)
Middle throw zoom lens (3.57 to 5.45:1)
Long throw zoom lens
V12H004R02
V12H004W02
V12H004S02
V12H004M01
V12H004M02
V12H004L04
Cables:
Component video cable (3RCA–VGA)
S-video cable
DVI to DVI cable, 10 ft
DVI to DFP cable, 10 ft
ELPKC19
ELPSV01
ELPKC20
ELPKC21
Macintosh adapter set (monitor and desktop adapter) ELPAP01
Remote control cable set ELPKC28
Distribution amplifier ELPDA01
ATA shipping case ELPKS47
Kensington®security lock ELPSL01
High resolution document imager
High resolution document camera
ELPDC02
V12H064020

Setting Up the Projector 13
1
Setting Up the Projector
This chapter gives you basic information on setting up the projector:
where to position it and how to connect it to a video source (such as a
VCR or DVD player) or to a laptop or desktop computer.
Follow the instructions in this chapter on:
■Positioning the projector
■Connecting to video equipment
■Connecting to a computer
■Connecting an external monitor
■Playing sound through the projector
■Using the remote control as a wireless mouse

14 Setting Up the Projector
Positioning the Projector
If you’re setting up the projector yourself
and it isn’t already installed in the theater
or conference room you’re using, you’ll
probably want to place it on a table in front
of the screen, as shown. a
This lets you stand in the front of the
room, face the audience, and remain
close enough to the equipment to be able
to control it. Try to leave as much space as possible between the
projector and the screen to get a good-size image.
If you’re using the standard lens, refer to the figure below to help you
determine placement. (For detailed guidelines on placing the projector
with any lens, see page 112.) Note that image size increases with
distance, but can vary depending on how you’ve adjusted the optical
zoom and other settings.
Also keep these considerations in mind:
■Place the projector on a sturdy, level surface.
■Make sure there is plenty of space for ventilation around and
under the projector. Do not set the projector on top of loose
papers that could block the vents under the projector.
■Make sure the projector is within 10 feet of a grounded electrical
outlet or extension cord.
note
You can mount the projector
on the ceiling, or place it
behind a translucent screen
for rear projection. See
page 111 for details.
3 to 5 ft7 to 10 ft37 to 50 ft approx. distance
from screen
TBD

Setting Up the Projector 15
Ideally, you should place the projector directly in front of the center of
the screen, facing it toward the screen squarely. If the projector isn’t
positioned this way, the image will be “keystone” shaped, instead of
square or rectangular. If this happens, you can use the projector’s
Quick Corner™function to readjust the shape (see page 40).
You can place the projector anywhere between the bottom and top
of the screen, and then use the Lens Shift to raise or lower the image
(see page 39).
If you place the projector below screen level, you’ll have to tilt it up by
extending its feet. This causes the image to lose its square shape, but
you can correct the distortion by pressing the Keystone button as
described on page 40.
Overhead View
Projector
Screen
Ideal
height
Side View
Screen
note
After positioning the
projector, you may want to
connect a Kensington
MicroSaver®anti-theft
device to the lock port on the
projector’s left side. You can
purchase this from EPSON;
see “Optional Accessories” on
page 12.

16 Setting Up the Projector
Connecting to Video Equipment
You can connect up to five video sources to the projector at the same
time. Before starting, look at your video equipment to determine its
available video-output connections:
■If your video player has a yellow RCA video output connector, see
“Connecting a Composite Video Source” on page 17.
■If your video player has an S-video connector, see “Connecting an
S-video Source” on page 18.
■If your video player has a component video port (three connectors
labeled either Y/Cb/Cr or Y/Pb/Pr), see “Connecting a
Component Video Source” on page 19.
■If your video player has an RGB video port (either a single
connector for a VGA monitor cable, or three connectors labeled
R/G/B), see “Connecting an RGB Video Source” on page 20.
Note that connecting a cable for RGB video provides the highest
quality of video transfer; component video is the next-best system,
followed by S-video and finally composite video (using an RCA
cable).
After connecting any video cables, you may also want to:
■connect a monitor to the projector so you can view your
presentation close-up as well as on-screen; see page 28
■connect an audio cable to play sound through the projector; see
page 29
RCA connector
(composite video)
S-video connector
(4-pin mini-DIN)
BNC connector
(component video)
VGA connector
(RGB video)

Setting Up the Projector 17
Connecting a Composite Video Source
1. Locate an RCA video cable (one is usually provided with your
video equipment).
2. Connect the cable to the yellow video output connector on your
player and the yellow Video connector on the projector:
3. If you want to play sound through the projector, see page 29 for
instructions on connecting an audio cable.
4. If you don’t need to make any other connections, see Chapter 2
for instructions on turning on the projector and adjusting the
image. Once the projector is turned on, be sure to select Video as
the source to see your image (see page 34).

18 Setting Up the Projector
Connecting an S-video Source
1. Locate an S-video cable (one is usually provided with your video
equipment, or you can purchase it from EPSON; see page 12).
2. Connect the cable to the S-video connector on your player and
the S-Video connector on the projector:
3. If you want to play sound through the projector, see page 29 for
instructions on connecting an audio cable.
4. If you don’t need to make any other connections, see Chapter 2
for instructions on turning on the projector and adjusting the
image. Once the projector is turned on, be sure to select S-Video
as the source to see your image (see page 34).

Setting Up the Projector 19
Connecting a Component Video Source
1. Locate a component video cable (one may be included with your
video equipment).
Look at the connectors at one end of the cable. If they are
bayonet-style (BNC) connectors, continue on to the next step. If
they are RCA connectors, you’ll need to attach commercially
available BNC adapters to plug the cable into your projector.
2. Connect the cable (with the adapters) to your player and the BNC
connectors on the projector. Match the Y/Cb/Cr (or Y/Pb/Pr)
connectors on your player to the corresponding connectors on the
projector.
3. If you want to play sound through the projector, see page 29 for
instructions on connecting an audio cable.
4. If you don’t need to make any other connections, see Chapter 2
for instructions on turning on the projector and adjusting the
image. Once the projector is turned on, be sure to do the
following:
■Enter the projector’s Setting menu, then change the BNC
Input setting to YCbCr or YPbPr, as needed (see page 70).
■After exiting the menu system, select BNC as the source to see
your image (see page 34).
BNC adapters

20 Setting Up the Projector
Connecting an RGB Video Source
Follow these instructions to connect the projector to a video player
that has an RGB video output port. Depending on the type of
connector on your player, you’ll need to use the appropriate cable:
■If your player has a single VGA connector, see below.
■If your player has three connectors labeled R/G/B, see
“Connecting Using a BNC Cable” on page 21.
Connecting Using a VGA Computer Cable
1. Locate the VGA computer cable provided with the projector.
2. Connect the cable to the video port on your player and the
Computer 1 or Computer 2 port on the projector.
3. If you want to play sound through the projector, see page 29 for
instructions on connecting an audio cable.
4. If you don’t need to make any other connections, see Chapter 2
for instructions on turning on the projector and adjusting the
image. Once the projector is turned on, be sure to:
■Enter the projector’s Setting menu, then change the
Computer1 Input (or Computer2 Input) setting to
RGB-Video (see page 70).
■After exiting the menu system, select Computer 1 (or
Computer 2) as the source to see your image (see page 34).