Epson PowerLite S1 User manual

1
User’s Guide
EPSON PowerLiteS1

2
Meaning of Symbols
Meaning of Symbols
The terms ‘this unit’ and ‘this projector’ which appear in this manual may also refer to the accessories supplied with the projector and other optional products.
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON
product. EPSON is not responsible for any use of this information as applied to other products.
Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by
purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.)
failure to strictly comply with SEIKO EPSON CORPORATION’s operating and maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated
as Original EPSON Products or EPSON Approved Products by SEIKO EPSON CORPORATION.
EPSON is a registered trademark of SEIKO EPSON CORPORATION.
EPSON Connection, EPSON Store, and Extra Care are service marks; and PrivateLine, Presenters Club, and PowerLite are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in
those marks.
Copyright © 2003 by Epson America, Inc. 4/03
cIndicates the possibility that people may be injured or the equipment may be damaged if these symbols are ignored.
pIndicates important related information or useful information and things you should know.
sIndicates related topics and pages which contain more detailed information.
gProvides terminology definitions. See “Glossary” on page 61.

3
Features
Auto setup (Computer
connections)
The projector analyzes the signal of the
computer to which it is connected and
automatically makes adjustments to
ensure optimal projection results. See
“Functions for Enhancing Projection”on
page 29.
Color mode
Image quality can be selected
according to the type of scene. See
“Selecting a color mode” on page 29.
Compact and lightweight
The projector is compact and easy to
carry.
◗Dimensions:
10.4 (d) × 14.6 (w) × 4.2 (h) inches
26.5 (d) × 37 (w) × 10.6 (h) cm
◗Weight:
approximately 7 lbs (3.2 kg)
Clear, vivid, images
The projector's high resolution and high
luminance achieves a legible display.
Project sharp, detailed images, even in
bright places.
Ease of use
Various projector operations can be easily
performed using the included remote
controls, as follows:
◗pausing projection
◗zooming in on important areas of an
image
Unique presentation function
The mouse pointer can be moved
around on the computer screen during
projection using the included
presentation remote control.
(wireless mouse)

4
Contents
Before Using the Projector
Part Names and Functions 6
Front/Top 6
Control panel 7
Rear 8
Base 9
Remote Control 10
Installation 12
Installation method 12
Projection distance and screen size 12
Other installation methods 13
Connecting to a Computer 14
Compatible computers 14
Projecting images from a computer 14
Playing sound from a computer 15
Connecting to an external monitor 16
Presentation Remote Control 16
Connecting to Video Equipment 20
Projecting video images 20
Playing sound from video equipment 21
Basic Operation
Turning on the Projector 22
Turning off the Projector 24
Adjusting the Display 25
Adjusting the projection size 25
Setting the focus 25
Adjusting the projection angle 26
Keystone 27
Selecting the Input Source 28
Advanced Operation
Functions for Enhancing Projection 29
Adjusting computer generated images 29
Selecting a color mode 29
A/V Mute 30
Freeze 30
Projecting in widescreen (changing aspect ratio) 31
E-Zoom 31
Configuration Menus 32
Menu operation 33
Function list 36

5
Troubleshooting
When You Suspect a Problem 43
Power indicator 43
Warning indicator 44
When the indicators provide no help 45
Where to Get Help 53
Telephone Support Services 53
Appendix
Projector Care 54
Cleaning 54
Replacing consumables 56
Optional Accessories 60
Glossary 61
Cable Format 63
Supported Display Resolutions 64
Specifications 65
Important Safety Instructions 66
FCC Compliance Statement 68
Warranty 69
Index

6
Part Names and Functions
Before Using the Projector
Part Names and Functions
Front/Top
•remote control infrared receiver sP. 11
Receives signals from the remote control.
•ventilation outlet
•lens cover
Attach when not using the projector to prevent the
lens from becoming dirty or damaged.
•focus ring sP.25
Adjusts the image focus.
•front foot (left) sP.26
Another front foot is located on the
right side.
Extend and retract to adjust the
projection angle.
•foot button (left) sP.26
Another foot button is located on the
right side.
Press both buttons when extending
and retracting the front feet.
•speaker
•handle
Pull out this handle to use when
carrying the projector.
•control panel sP. 7

7
Part Names and Functions
Control panel
•[Power] button sP.22
Turns the projector on and off.
•Power indicator sP.22, P.43
Flashes or lights in different colors to
indicate the operating status of the
projector.
•[u][d][l][r] buttons sP.33
•[u][d]: keystone correction buttons sP.27
Press to correct keystone distortion in images.
•[Wide][Tele]: zoom buttons sP.25
•Warning indicator sP.44
Flashes or lights in different colors to
alert you to problems with the projector.
•[Menu] button sP.32
Displays or hides the
configuration menus.
•[Source] button sP.28
Switches the input source
between the Computer/
Component Video port,
S-Video port and Video port
each time the button is pressed.
•[e] button sP.34
Accepts a menu item or
advances to the next screen or
menu when viewing
configuration menus.
•[Esc] button sP.35
Stops the current function.
Displays the previous screen or
menu when viewing
configuration menus.

8
Part Names and Functions
Rear
•Computer/Component Video port
sP. 14, P. 20
Inputs analog video signals from a
computer and Component Videog
signals from other video sources.
•Monitor Out port sP. 16
Outputs the projected analog
computer signal to an external
monitor. This feature is not available
for video signals.
•remote control infrared receiver
sP. 11
Receives signals from the remote
control.
•power inlet sP.22
Connects the power cable.
•Video port sP. 20
Inputs Composite Videogsignals to
the projector.
Connect using an A/V cable.
•S-Video port sP. 20
Inputs S-Videogsignals to the
projector.
Connect using an S-Video cable.
•security lock sP.62
•Audio port sP. 15, P. 21
Inputs audio signals to the projector.
Connect using an A/V cable, or a stereo
RCA cable.
When using computer and video
equipment alternately, swap the cable or
use an audio switch.
•Control (RS-232C) port sP.63
Connects the projector to a computer using an
RS-232C cable. This port is for control use and
should not be used by the customer.
•remote control holder sP. 11
Store the remote control in here when
not in use.

9
Part Names and Functions
Base
•ceiling mount holes (3 points)
Install the optional ceiling mount
here when suspending the projector
from the ceiling.
•lamp cover sP.57
Open this cover when replacing the
lamp inside the projector.
•air filter (air intake vent) s
P.55, P.59
Prevents dust and other foreign
particles from being drawn into
the projector. When replacing
the lamp, replace the air filter
also.
•handle
Pull out this handle to use when
carrying the projector.
•rubber foot

10
Remote Control
Remote Control
•remote control infrared transmitter
Transmits remote control signals.
•[Aspect] button sP.31
Changes the aspect ratio of images from 4:3 to 16:9.
•[Source] buttons sP.28
[Computer]: Switches to the signal source being input
to the Computer/Component Video port.
[S-Video/Video]: Switches between the signal source
being input to the S-Video port and the Video port.
•[E-Zoom] buttons sP.31
z: Enlarges part of the image without changing the size
of the projection area.
x: Reduces the part of the image that has been
enlarged using the [z] button.
•[Esc] button sP.35
Stops the current function.
Displays the previous screen or menu when viewing
configuration menus.
•[e] button sP.34
Accepts a menu item or advances to the next
screen or menu when viewing configuration menus.
•[u][d][l][r] buttons sP.33
Selects menu items and setting values.
•[Power] button sP.22
Turns the projector on and off.
•[A/V Mute] button sP.30
Momentarily turns off the audio and video. •[Freeze] button sP.30
Keeps the current image on the screen.
•[Auto] button sP.29
Use this button to automatically adjust computer
images to their optimum settings when automatic
setup has been set to “OFF.”
•[Color Mode] button sP.29
Selects the color mode. The color mode changes in
the order of Dynamic, Presentation, Theatre, Living
Room and sRGBgeach time the button is pressed.
•[l][r]: volume buttons
Adjusts the volume.
•[Menu] button sP.32
Displays or hides the configuration menus.

11
Remote Control
Before using the Remote Control
Remove the insulating tape.
Using the Remote Control
Operate the remote control by aiming it at the remote control infrared receiver
on the projector.
Operating range
Operable distance: Max. approximately 20 feet (6 m)
(May be shorter depending on conditions.)
Operable angle: approximately 30° horizontally, 15° vertically
* The remote control infrared receiver on the back of the projector can also be
used under the same conditions.
Storage
When not using the remotecontrol, please store it in the remote control holder
on the projector.
1Open the remote control holder.
2Place the remote control in the remote control holder.
3Close the remote control holder until it clicks into place.
pIf direct sunlight or fluorescent lighting hits the remote control infrared
receiver, you may not be able to use the remote control.
remote control
infrared receiver
remote control
infrared receiver
15°
15°
30° 30°
Max
20 feet
(6 m)

12
Installation
Installation
Installation method
Set up the projector so that it is at right angles to a screen.
Projection distance and screen size
cBe sure to read the Important Safety Instructions before installation.
pWhen setting up the projector against a wall, leave a space of at least
7.9 inches (20 cm) between the projector and the wall.
Projection distance:
3-34 feet
(89-1050 cm)
7.9 inches (20 cm) or more
90°
Center of
lens
Distance from center of lens
to bottom edge of screen
Distance from projector to screen
screen size

13
Installation
Other installation methods
Rear projection
(Using a translucent screen)
Ceiling projection
Ceiling/Rear projection
(Using a translucent screen)
The optional ceiling mount is required when installing the projector from a
ceiling. Please contact your dealer if you wish to use this method, as special
equipment is required for installation. See “Optional Accessories” on page 60.
pWhen using rear projection, or projecting from a ceiling, select the
appropriate mode in the “Setting”
→ “Screen” → “Projection”
configuration menu. See “Setting menu” on page 39.

14
Connecting to a Computer
Connecting to a Computer
Compatible computers
Condition 1: Check that the computer has an image output port, such as an
RGB port, monitor port or CRT port.
Some computers with a built-in monitor and some notebook computers may
not be compatible. Please refer to your computer manual for further details.
Condition 2: The display frequency and resolution of the computer must
correspond to that of the projector. See “Supported Display Resolutions” on
page 64.
Notebook connection
Setup
Press and hold the [Fn] key, followed by the appropriate function number key
that lets you display on an external monitor. Refer to your computer’s
documentation for further details.
◗It may take a few moments until the computer image is projected.
◗In Windows, a dialog box may appear to alert you that new display
hardware has been found. Follow the on-screen instructions to proceed.
If you have any problems, check the troubleshooting chapter for
possible solutions. See “Troubleshooting” on page 43.
◗Depending on the PC, the monitor may go blank when using the
external video output on the computer.
Projecting images from a computer
Different cables are used depending on whether the monitor port of your
computer is a Mini D-Sub 15Pin, 5BNCgor 13w3 port.
When using a Mini D-Sub 15 pin connector
cWhen connecting, be sure to:
• Turn off the power for both the projector and the computer.
Damage may result if you try to make a connection when the power is
switched on.
• Check the connector types.
Damage may result if you attempt to insert a connector into the
incorrect port.
pYou may need to purchase a separate adapter depending on the shape of
the computer’s port. Refer to the documentation provided with the
computer for further details.
pWhen using a notebook or a PC with a built-in monitor, select external
video output on the computer.
To monitor port
To Computer /
Component Video port
Computer cable
(accessory)

15
Connecting to a Computer
When using a 5BNC port
When using a 13w3 port
Playing sound from a computer
You can play sound from a computer through the projector’s built-in speaker.
Volume adjustment
Press [l] or [r] on the remote control.
You can also adjust the volume from the configuration menu.
([Menu] button →“Setting” →“Volume”) See “Setting menu” on page 39.
p• Select “Computer” in the “Image”
→ “Input signal” configuration
menu. See “Image menu” on page 36.
• Do not bind the power cable and computer cables together. Interference
or operational problems may result.
• A particular type of cable may be required for some workstations. Please
check with the maker of your workstation.
To monitor port VGA-HD15/BNC PC
cable (optional)
To Computer /
Component Video port
To monitor port 13w3 cable
(commerically available) To Computer/
Component Video port
pWhen using computer and video equipment alternately, swap the cable or
use an audio switch.
To audio out port stereo mini jack - 2RCA cable
(commercially available)
RCA jack
To Audio port
stereo mini
jack

16
Connecting to a Computer
Connecting to an external monitor
The image being input into the projector can be displayed on a computer
monitor.
Presentation Remote Control
You can use the presentation remote control as a wireless mouse to control
the mouse pointer on the computer screen.The presentation remote contains
all the functions necessary for giving a presentation. Functions include: Page
Up/Page Down, Left/Right mouse click, A/V mute, freeze, and mouse pointer.
Compatible computers
Windows: Windows 98/2000/Me/XP
(Only compatible with the full versions of Windows. Upgraded
versions cannot be used.)
Macintosh: Mac OS9.1 or later/OS X 10.1 or later
p• Video images cannot be output to an external monitor.
• Setting gauges (for keystone correction, etc.) and configuration menus
will not be displayed on an external monitor.
monitor cable To Monitor Out port
p• The presentation remote receiver can only be connected to computers
with a standard USB interface.
• Some computer settings may have to be changed in order for the mouse
function to be used. Refer to your computer’s documentation for details.
Before using the presentation
remote control, remove the
insulation tape.

17
Connecting to a Computer
Installing the driver for Windows
Screen contents will differ according to the version of Windows you are using.
This explanation uses screenshots taken from Windows 98.
Driver installation is not required for the Macintosh.
1Connect the accessory Presentation Remote Receiver to the USB
port of the computer.
The “Add New Hardware” wizard is displayed.
Under normal circumstances, maintain the default settings and click
“Next” to proceed.
2Click “Next.”
3Keeping the defaults, click “Next.”
4Click the check box next to “Specify a location.” Type
“C:\WINDOWS” and click “Next.”
Infrared receiver
To USB port Presentation Remote
Receiver (accessory)
p• You may need to enter a different location to search for the OS files that
you are using.
• Click on “Browse” if you want to change the default search location.

18
Connecting to a Computer
5Click on “Next” to confirm the message which is displayed.
6Click on “Finish.”
The installation of the driver is complete.
pThe driver installation screen is displayed a second time.
(The presentation remote control driver has two parts; the mouse driver
and the keyboard driver.) Follow the on-screen instructions to complete the
installation.

19
Connecting to a Computer
Part Names and Functions
Operate the presentation remote control by aiming it at the presentation remote receiver.
When using the Freeze or A/V Mute functions, aim the presentation remote control towards the remote control infrared receiver of the projector.
•[L Click] button
Acts as a mouse left-click.
•[Freeze] button
Keeps the current computer or
video image on the screen.
•[Page Up] / [Page Down] buttons
Press these buttons to scroll back and forth
through pages when projecting a
presentation.
•[A/V Mute] button
Momentarily turns off the audio and video.
•remote control infrared transmitter
Transmits remote control signals.
•joystick
To move the mouse pointer, move the
joystick in any of the following
directions: up, down, left, right, diagonally.
•[R Click] button
Acts as a mouse right-click.
•Double click:
Push the [L Click] button twice.
•Drag and drop:
To drag, press and hold the [L Click] button and move
the cursor with the joystick.
The item will be dropped when [L Click] is released.
pIf the mouse button settings have been reversed on the computer, the
operation of the remote control buttons will also be reversed.

20
Connecting to Video Equipment
Operating range
Operable distance: Maximum approximately 20 feet (6 m)
(may be shorter depending on conditions)
Operable angle: Approximately 30° horizontally, 15° vertically
Connecting to Video Equipment
Projecting video images
For Composite Video (DVD, VHS, Video games)
For S-Video (DVD, VHS, Video games)
cWhen connecting, be sure to:
• Turn off the power for both the projector and the video equipment.
Damage may result if you try to make a connection when the power is
switched on.
• Check the connector types.
Damage may result if you attempt to insert a connector into the
incorrect port.
30°
Max 20 ft (6 m)
30° 15°
15°
To video
out port
AV cable (yellow)
(commercially
available)
To Video
port
To audio out
port
To Audio
port
To S-Video out
port
S-Video cable
(commercially
available)
To S-Video
port