Epson ES-1200C Pro PC Specification sheet

t

EPSON
®
ES-1200C Pro Mac
Getting Started

A Note Concerning Responsible Use of
Copyrighted Materials
Like photocopiers, scanners can be misused by improper
copying of copyrighted material. Although Section 107 of the
U.S. Copyright Act of 1976 (Title 17, United States Code), the
“fair use” doctrine, permits limited copying in certain
circumstances, those circumstances may not be as broad as
some people assume. Unless you have the advice of a
knowledgeable attorney, be responsible and respectful by not
scanning published material without the permission of the
copyright holder.
ES-1200C is a trademark of Epson America, Inc.
EPSON is a registered trademark of Seiko Epson Corporation.
General notice: Other product names used herein are fur identification purposes only and may be
trademarks of their respective companies. EPSON disclaims any and all rights in those marks.
Copyright © 1994 by Epson America, Inc.
Torrance, California, USA

lntroduction
This package contains everything you need for professional
quality color scanning:
Ll An EPSON
®
ES-1200C™ color scanner
Ll Adobe™ Photoshop™ a powerful image-editing program
Ll Kai’s Power Tools,™ a Photoshop plug-in for editing images
Q ScanTastic™ a plug-in for scanning images into Photoshop
D A SCSI system cable.
This booklet tells you how to set up your scanner, install the
software, and scan a picture. If you need detailed information
after you begin scanning, you can consult the individual
manuals for the ES-1200C Scanner, Adobe Photoshop, Kai’s
Power Tools, and ScanTastic.
System and Memory Requirements
To install the scanner and software, you should have the
following:
Q Power Macintosh™ or a Macintosh
®
computer with a 68030
or 68040 processor
Q Apple
®
system software 7.0 or higher
Ll 10MB or more of application RAM
Cl 100MB of hard disk space
Q A color monitor. One with a 24-bit or 32-bit video display is
recommended.

Setting Up the Scanner
1. Take the scanner out of the box.
2. Remove the tape securing the scanner cover and pull out
the cardboard from the top of the scanner.
3. Place the scanner on a flat, stable surface with its rear panel
facing you.
4. Locate the round screw knob in the middle of the rear
panel.
5. Turn the screw counterclockwise. If necessary, use a coin.
The screw has a built-in spring, so it pops out a little when
it is released. You cannot remove the screw.
2

6. Connect the power cable to the power inlet on the rear of
the scanner and the other end into an appropriately
grounded outlet as shown below.
If the scanner comes on when you plug it in, turn it off by
pressing the OPERATE button.
R
Warning:
Whenever you turn off the scanner, wait at least 20 seconds
before turning it back on. Rapidly turning it on and off can
damage it.
3

Connecting the Scanner to Your
Macintosh
Use this procedure to connect the scanner directly to the SCSI
port on your computer using the SCSI cable included with the
scanner. This cable has a 25-pin connector on one end and a
50-pin connector on the other.
If you are already using the SCSI port on your computer for
another SCSI device, such as an external hard disk, you need a
SCSI cable with a 50-pin connector on both ends. You can then
connect the scanner to your other SCSI device, following the
instructions in Chapter 1 of your ES-1200C User’s Guide.
e
Caution:
Be sure that your Macintosh, scanner, and any other SCSI
devices are turned off before you plug in the cable.
1.
Plug the 25-pin connector into the SCSI port on the
Macintosh. This port has a C- icon above it. Tighten the
two screws on the sides of the connector.
2.
Connect the 50-pin end of the cable to either the top or
bottom SCSI connector of the scanner; then fasten the
connector with the wire clamps on its side.
3.
Turn on the scanner, then the Macintosh. (Always turn the
scanner on before the computer.)
4

Installing Photoshop
Now that you have connected the scanner and the Macintosh,
you can install your software.
1. Turn off any virus-protection software you are using until
you finish installing the software programs. You do this by
holding down the Shift key while you restart your
Macintosh.
2. Insert the Photoshop Installer Disk 1 in the Macintosh and
double-click the Install Adobe Photoshop icon.
3. When the initial screen appears, click OK to continue. Then
follow the instructions that appear on following screens,
removing and inserting diskettes as prompted.
By default, the Installer does an easy installation and installs
the entire program. If you are low on disk space, you may
want to do a custom installation so you specify that only
certain software components be installed. See your
Photoshop manual for more information.
4. When a message appears telling you that installation was
successful, click Quit to exit the Installer.
5. When prompted to restart your Macintosh, hold down the
Shift key and click the Restart button.
Note:
If you have SuperMatch,™ NEC
®
AccuColor™ or another monitor
calibration utility installed, skip to step 7.
6. Open the Calibration folder (in the Photoshop folder)
and drag the Gamma icon to the System Folder. When
prompted to put Gamma in the Control Panels folder,
click OK.
5

7. Open the Adobe Photoshop folder if it is not already open,
and double-click the Adobe Photoshop icon.
8. Enter your name in the text box. If you wish, also type the
name of your organization.
9. Type the serial number of the Photoshop program. You can
find it on the Photoshop registration card and on one of the
installation diskettes.
10. Click OK.
11. Choose Quit from the File menu in the upper left corner of
the screen.
This closes Photoshop so you can install Kai’s Power Tools
and ScanTastic.
lnstalling Kai's Power Tools
1.
2.
3.
4.
5.
Insert Disk 1 of the Kai’s Power Tools disks and double-click
the Install KPT Filters 2.0a icon.
A dialog box appears prompting you to open the Plug-ins
folder.
Locate and open the Plug-ins folder in the Adobe Photoshop
folder.
With the Plug-ins folder open, click Extract.
When installation is complete, eject the Kai’s Power Tools
diskette.
6

Installing ScanTastic
1. Insert the ScanTastic Installation Disk 1 into your Macintosh
and double-click the ScanTastic ps Installer icon.
2. When the initial screen appears, click Continue. Read the
next screen that opens and choose Continue.
3. If prompted, enter your full name, organization, and serial
number (found on the diskette label and registration card).
4. Click Install to begin installation. When the next screen
appears, click Yes.
A dialog box then opens the Photoshop folder and prompts
you to locate the Plug-ins folder. Click once to select the
Plug-ins folder. Then click the Install into “Plug-ins” button
at the bottom of the dialog box.
If the Installer cannot find the Photoshop folder, open
folders as needed to locate it. Then select the Plug-ins
folder and click Install into “Plug-ins.”
If you get a message that there is not enough room on your
hard disk to install ScanTastic, do a custom installation. See
your ScanTastic manual for more information.
5. Insert additional diskettes, if prompted.
6. When installation is complete, you are prompted to restart
your Macintosh. Click Restart.
7