manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. ERA
  6. •
  7. Security Sensor
  8. •
  9. ERA P700 User manual

ERA P700 User manual

Ceiling Mounted PIR Motion Detector
Model: P700
ERA Home Security Ltd
Valiant Way, Wolverhampton,
West Midlands, WV9 5GB.
Email: [email protected]
2. GET TO KNOW
YOUR PRODUCT
1. INTRODUCTION 4. PCB LAYOUT
The Sensor works by detecting the human body’s infrared
spectrum. When human movement takes place within the scope,
the detector receives the signal and inputs it into the
microprocessor after magnification. Microprocessor continues to
sample infrared signal and sends wireless signal to the control
panel after calculating. The products can be applied in banks,
warehouses and homes etc.
Accurate Detection
360 detection, no dead angle. Automatic temperature
compensation and anti-air turbulance technology
False Alarm Prevention
Digital dual core fuzzy logic infrared control processing technology.
Effectively identify interferance signals from body movement
signals through intelligent analysis.
Space-saving
Ceiling mounted, not much space occupation.
Integrated to home decoration, suitable for most premises.
Energy-saving
Featured energy-saving mode enables 1 year standby.
AA LR6 1.5V
AA LR6 1.5V
3. FEATURES
INSTALLATION
MANUAL
5. LED
INDICATION
The LED indicator can be turned on or off by setting jumpers.
See ‘PCB Layout’ above.
Flash Continuously: Under self-testing state
Flash Once: Intruder is detected
Flash Twice: Testing mode is finished, enters power-saving
Flash Once Every 3 Seconds: Low battery indication,
please change batteries.
6. DETECTION
RANGE
Infrared Sensor Zone Setting
LED ON/OFF
Infrared Sensor: Detecting Human Body’s infrared spectrum.
DO NOT touch the surface by hand and keep it clean.
1. Test Button
2. Detection Lens
3. LED Indicator
4. Mounting Plate
3.6m
6m
Side View
8. USAGE
11. TESTING
12. CONNECT
WITH CONTROL
PANEL
13.
SPECIFICATION
Choose a suitable position
and fix the mounting plate
on the ceiling with screws.
Fasten the detector on the
mounting plate in a
clockwise direction. It is
suggested to mount it at
the height of 2.5-6 metres
from the ground.
Keep the detector away
from the air conditioner,
electronic fan,
refridgerator, over, heater
or any other objects which
will cause a fast change in
temperature.
Avoid mounting it in direct
sunlight or any objects
blocking the lens, so the
detection is not affected.
Testing mode: Press the test button, the sensor enters testing
mode and detects once every 10 seconds. After 3 minutes, the LED
flashes twice, the sensor enters the power saving mode.
Power-Saving Mode: In working state, if the sensor is triggered
twice within 3 minutes, it will enter sleeping mode to save power.
After no movement within the following 3 minutes, the sensor goes
back to working state.
Remove the battery activation strip to activate batteries. It will
enter working state after one-minute’s self testing.
9. MODE SETTING
10. INSTALLATION
After installation, power on the detector. After
self-testing for 1 minute, press the test button,
walk in the scope by crossing the infrared
spectrum (see diagram below) and watch the
LED indicator to make sure it is working. The
LED indicator will flash once when body
movement is detected.
When the control panel is in a connecting state, press the
test button twice to send wireless signal. One beep is heard
after the panel receives signal, meaning a successful
connection.
Arm the system and trigger the detector again. This panel
will alarm immediately, indicating a successful connection
to the panel.
Top View
360°
High detection
sensitivity
Low detection
sensitivity
Power Supply
Static Current
Alarm Current
Installation Height
Detection Scope
Transmitting Distance
Radio Frequency
Housing Material
Operation Condition
Sensor Dimensions
Mounting Plate Dimensions
DC 3V (AA LR6 1.5V Battery x 2 Pcs)
< 13uA
< 15mA
2.5-6m
Dia. 6m (when installation height is 3.6m)
< 80m (in open area)
433.92MHz (±75KHz)
ABS Plastic
Temperature: 0°C ~ +55°C
Relative Humidity: <80% (non-condensing)
90 x 90 x 36.8mm (L x W x H)
56 x 56 x 8mm (L x W x H)

Popular Security Sensor manuals by other brands

Securiton CCD 573X Series datasheet

Securiton

Securiton CCD 573X Series datasheet

Elcometer 266 user guide

Elcometer

Elcometer 266 user guide

Design Light WYL-CR-M3-BI-01 Assembly instruction

Design Light

Design Light WYL-CR-M3-BI-01 Assembly instruction

Omron ZS-HL Series user manual

Omron

Omron ZS-HL Series user manual

Evikon E2610-NH3 user manual

Evikon

Evikon E2610-NH3 user manual

PCB Piezotronics M119B11 Installation and operating manual

PCB Piezotronics

PCB Piezotronics M119B11 Installation and operating manual

Owon CMD344 quick start guide

Owon

Owon CMD344 quick start guide

McCue FlexCore Guardrail installation instructions

McCue

McCue FlexCore Guardrail installation instructions

schmersal RSS 36-D-R manual

schmersal

schmersal RSS 36-D-R manual

DBI SALA Saflok User instruction manual

DBI SALA

DBI SALA Saflok User instruction manual

STEINEL PROFESSIONAL IR Quattro KNX operating instructions

STEINEL PROFESSIONAL

STEINEL PROFESSIONAL IR Quattro KNX operating instructions

Rielta FOTON-SH installation guide

Rielta

Rielta FOTON-SH installation guide

Fluke PLS SLDR user manual

Fluke

Fluke PLS SLDR user manual

bloom lab BL-REF-2 manual

bloom lab

bloom lab BL-REF-2 manual

Yamorc YD6016LN quick start

Yamorc

Yamorc YD6016LN quick start

Satel SLIM-DUAL manual

Satel

Satel SLIM-DUAL manual

Pyle PRMDC10 user manual

Pyle

Pyle PRMDC10 user manual

TEKTELIC Communications Gen4 user guide

TEKTELIC Communications

TEKTELIC Communications Gen4 user guide

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.