Sauder Shoal Creek 408920 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Executive Desk
Shoal Creek Collection | Model 408920
Business or pleasure.
Works both ways.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-34
Français pg 35-39
Español pg 40-44
Lot # 392369 06/20/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
2-3
4-5
6-34
35-39
40-44
45-46
47
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C3 RIGHT UPRIGHT (1)
D3 LEFT UPRIGHT (1)
D28 LARGE RIGHT DRAWER SIDE (2)
D29 LARGE LEFT DRAWER SIDE (2)
D77 DRAWER BACK (2)
D78 LARGE DRAWER BACK (2)
D132 RIGHT DRAWER SIDE (2)
D138 LEFT DRAWER SIDE (2)
D707 DRAWER BOTTOM (4)
EE3 TOP (1)
G MODESTY PANEL (1)
H RIGHT FRONT/LEFT REAR LEG (2)
I LEFT FRONT/RIGHT REAR LEG (2)
J KEYBOARD FRONT (1)
K KEYBOARD BACK (1)
L KEYBOARD SIDE (2)
M KEYBOARD SHELF (1)
M60 BOTTOM (2)
N2 DRAWER FRONT (2)
O DRAWER BOX FRONT (2)
T LARGE DRAWER FRONT (2)
U LARGE DRAWER BOX FRONT (2)
Y MOLDING (1)
Z END MOLDING (2)
408920 www.sauder.com/servicesPage 2
Part Identification Now you know
our ABCs.

Part Identification
A
B
C3
D3
EE3
M60
M60
GH
H
I
I
J
K
L
LM
N2
O
T
U
Y
Z
Z
408920www.sauder.com/services Page 3
D29
D28
D77
D78
D707
D707
D132
D138

Hardware Identification
LONG SUPPORT
ROD - 1
24A
TURNBUCKLE - 1
9A SHORT SUPPORT
ROD - 1
23A
(EXTENSION SET SHOWN SEPARATED)
FILE ROD - 4
8B
7F TWIST-LOCK®
FASTENER - 5 ANCHOR PLATE - 2
66G
10A SLIDE
CAM - 8
HINGE - 2
12H
CAM SCREW - 12
8F
HIDDEN CAM - 40
1F CAM DOWEL - 28 2F
(EXTENSION SET SHOWN SEPARATED)
WIDE EXTENSION
RAIL - 4
GG WIDE EXTENSION
SLIDE - 4
HH NARROW EXTENSION
RAIL - 4
JJ2 NARROW EXTENSION
SLIDE - 4
KK2
408920 www.sauder.com/servicesPage 4
FILE GLIDE - 4
15B
40AW CABINET RIGHT - 1 40AX CABINET LEFT - 1 40AY DRAWER RIGHT - 1 40AZ DRAWER LEFT - 1
22A SPACER - 2

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
31S BLACK 7/8" FLAT HEAD SCREW - 4
SILVER 1-1/8" FLAT HEAD SCREW - 4
10S
SILVER 1-1/4" MACHINE SCREW - 12
35S
BLACK 1-7/8" FLAT HEAD SCREW - 6
2S
GROMMET CAP - 1
1P
18S BROWN 1" FLAT HEAD SCREW - 4
3S GOLD 5/16" FLAT HEAD SCREW - 36
METAL PIN - 4
1R
23S SILVER 5/8" FLAT HEAD SCREW - 4
54S SILVER 9/16" LARGE HEAD SCREW - 10
PULL - 6
7K
32S BLACK 9/16" FLAT HEAD SCREW - 9
KNOB - 2
24K GROMMET - 1 10P
408920www.sauder.com/services Page 5
30S BLACK 1-9/16" FLAT HEAD SCREW - 16
GOLD 1" MACHINE SCREW - 2
50S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
Do not tighten the TWIST-LOCK® FASTENERS in this step.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the large holes in the
MODESTY PANEL (G).
G
7F
408920 www.sauder.com/servicesPage 6
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1534
to watch a video on how to assemble your unit.
STOP
If you purchased
the 408750
Hutch, assemble
that unit first.

å Push forty HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHTS (C3 and D3), both BOTTOMS (M60), and
the MODESTY PANEL (G). Then, insert the metal end of
twenty-eight CAM DOWELS (2F) into the HIDDEN CAMS.
Step 2
A
B
C3
D3
M60
M60
G
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
Do not insert
CAM DOWELS
into these edges.
(40 used)
(28 used)
Arrow
2F
1F
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
408920www.sauder.com/services Page 7

Step 3
å Turn twelve CAM SCREWS (8F) into the LEGS (H and I).
8F
H
H
I
I
Just think. The sooner
you do this, the sooner
you do something else.
408920 www.sauder.com/servicesPage 8
(12 used)

å Fasten one of each LEG (H and I) to the ENDS (A and B).
Tighten six HIDDEN CAMS.
Step 4
Curved edge
A
B
H
I
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
408920www.sauder.com/services Page 9
1
2
Curved edge
These surfaces
should be even.
These surfaces
should be even.
Edge with
HIDDEN CAMS

å Turn six BLACK 9/16" FLAT HEAD SCREWS (32S) into
the ENDS (A and B) until the shoulders of the SCREWS
rest on the surfaces of the ENDS.
å NOTE: Do not overtighten the SCREWS.
å Now, slide the END MOLDINGS (Z) onto the ENDS (A
and B). To do this, line up the grooves in the MOLDINGS
over the heads of the SCREWS in the ENDS. Using your
hands, apply pressure on the MOLDINGS as you guide
the MOLDINGS onto the ENDS.
å NOTE: If the MOLDINGS come up o of the SCREWS,
remove them and slide them on again.
Step 5
A
B
Z
Z
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
BLACK 9/16" FLAT HEAD SCREW
(6 used in this step)
32S
These edges
should be even.
These edges
should be even.
Shoulder
408920 www.sauder.com/servicesPage 10
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.