Ergolux ELDUAL3LGBA User manual

DUAL MOTOR 3 SECTION
LEG STANDING DESK
(BLACK & WHITE)
ELDUAL3LGBA & ELDUAL3LGWA

• Read all instructions before use and retain this user guide for future reference.
• Read all following safety precautions carefully before use.
• Your equipment i s intend ed for use in cool , dry co n diti ons. You shoul d a void storage
in extreme cold, hot or damp areas as this may lead to corrosion and other related
problems. Operating temperature 0-40°C
• If the power cord is damaged, cease use immediately and contact Kogan.com for
support.
• Unplug the power cord before cleaning. Wipe the dust from the surface using a
slightly damp cloth. Ensure any water does not come in contact with any internal
parts or connectors.
• Do not use any corrosive or abrasive materials to clean the product.
• The control box contains electronic components, metals, plastics, wires etc. ensure
it is disposed of in accordance with your local environmental legislation. Do not
dispose with general household waste.
• Ensure this product is completely and correctly assembled before use.
• Be familiar with all functions and program settings of the product before first use.
• The desk will emit a slight noise caused by the V-ribbed belt or brake system. This
is completely normal and will not affect the product’s operation or performance.
• This product can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
• Children should not be allowed play with this product.
• Cleaning and user maintenance should not be performed by children without
supervision.
• Retain the original packaging where possible, to use for any future transportation of
this product.
SAFETY & WARNINGS

Lay all components out on a clean floor and ensure all parts are included. If any pieces are
missing, check all packaging thoroughly, then contact help.Kogan.com for assistance.
1 Feet (x2)
2Lifting column (x2)
3 Connection rod
4Left support beam
5Right support beam
6Short beam (x2)
7Side bracket (x2)
8Power adapter
9Power adapter bracket
10 Handset
11 Control box
12 Power cord
13 Power adapter cable
COMPONENTS

Hardware list
AM6 (x4)
BM6 (x8)
CM6 (x8)
DSelf-tapping
screw (x6)
ECable tie (x6)
FSelf-tapping screw (x16)
G Allen key

Step 1: Installing the supporting beam and the side bracket.
• Connect the connection rod (3) to the left support beam (4) and right support beam
(5) and tighten using with the Allen key (G).
Note: If the connecting rod cannot be inserted into the supporting beam, loosen the
screws on the beam.
• Using M6 screw (A) attach the side brackets (6) to the left supporting beam (4) and the
right supporting beam (5) and tighten using the Allen key (G).
AM6 (x4)
GAllen key
ASSEMBLY

Step 2: Installing the lifting columns.
Use the M6 screw (B) to attach the lifting column (2) to the left supporting beam (4) and the
right supporting beam (5) and tighten them using the Allen key (G).
BM6 (x8)
GAllen key

Step 3: Installing the feet.
Attach the feet (1) to the lifting column (2) using the M6 screws (C) and tighten using the
Allen key (G).
CM6 (x8)
G Allen key

Step 4: Installing the power adapter bracket.
• Using the Allen key (G) adjust the distance of the supporting beams (4) to suit the
tabletop.
• Attach the power adapter bracket (9) in between the tabletop and supporting beam
(4).
G Allen key
Loosen
Tighten
Adjust
Do not adjust the supporting
beam beyond this hole

Step 5: Installing the tabletop, handset, control box and adapter.
• Attach the tabletop to the standing desk using the self-tapping screws (F).
• Attach the control box (11) to the tabletop in the position shown using the self-tapping
screws (F).
• Attach the handset (10) to the tabletop using the self-tapping screws (F) and insert the
power adapter (8) into the power adapter bracket (9).
F(x14)
Drill or impact driver

Step 6: Connecting the control box.
• Following the diagram below, connect the lifting column connectors to the control box
(9).
• Connect the handset connector (10) to the control box (11).
• Connect the power adapter cable (13) to the control box (11).
• Connect the power adapter cable (13) to the power adapter (8).
• Connect the power cord (12) to the power adapter (8).
Power adapter
Handset
Lifting columns

Step 7: Cable management.
• Remove the adhesive backing and attach the supplied cable ties (E) to the underside
of the tabletop.
• Tidy up and secure all the cables in place using the cable ties (E).
ECable ties (x6)
Remove
backing
Attach
Secure
cables

Handset Controls
Button
Description
▲
Raise the desk height
▼
Lower the desk height
1
First user defined height position
2
Second user defined height position
3
Third user defined height position
M
Memory button
A
Alarm button
Functions
Adjusting the height:
Press the ▲or ▼buttons to adjust the height of the desk. The LED display will show the
current height.
Memory function:
1. Once the desk has been set to the desired height, press the “Memory” button to
save the height. The LED will display .
2. Press “1”, “2” or “3” to save the height to the corresponding button. The LED will
display , or .
3. Pressing “1”, “2” or “3” will automatically adjust the desk to the height you saved.
OPERATION

Stand up alarm:
1. Pressing the “Alarm” button will enable the stand up alarm function. The LED will
display or .
2. After 2 seconds the LED display will flash. By default the stand up alarm timer is
set to 45 minutes. Use the ▲or ▼buttons to adjust the timer to the desired length.
Press any of the other buttons or wait 5 seconds to save the timer.
3. During the countdown, any operation will reset the timer. When the countdown
reaches the set time the LED will display and a 10 second alarm tone will play.
Pressing any button within the 10 seconds will reset the stand up alarm timer. If no
buttons are pressed within the 10 seconds, a follow up alarm tone will play in 5
minutes. If no buttons are pressed during the follow up alarm, the stand up alarm
function will be deactivated.
4. To d e a c t i v a te t h e s t a n d u p a l a r m , p r e s s a n d h o l d t h e “A l a r m” b u t t o n f o r 3 s e c o n d s .
The LED will display or .
Anti-collision adjustment:
This desk features an anti-collision function. During height adjustment if the tabletop
comes in contact with an object it will stop and reverse to avoid damage.
1. By default, the anti-collision sensitivity is set to A-3 (high). Press and hold ▲▼
buttons simultaneously for 5 seconds to change the sensitivity levels of the anti-
collision function.
Note: If the LED does not display any codes after pressing the ▲▼buttons, the
desk does not feature the anti-collision function.
2. Each time you press and hold the ▲▼buttons the sensitivity level will cycle in the
following order: A-3, A-2, A-1, A-0. Refer to the table below for sensitivity levels.
Setting
Sensitivity level
A-3
High
A-2
Medium
A-1
Low
A-0
Off

Column stage
3
Rated voltage
AC 100V-240V, 50/60Hz
Max. weight capacity
100KG
Height range
620-1270mm (without tabletop)
Width range
1100-1700mm
SPECIFICATIONS

The following tips will help you detected and eliminate some common faults and errors. If
the problem cannot be fixed or the fault is not listed below, please contact help.Kogan.com
for support.
Problem
Solution
No response after pressing and
holding the down arrow.
Check if all the cables be connected well.
No response after pressing up or down
arrow.
Check if all the cables be connected well.
Rising speed is low.
Check if overloaded, max loading: 100kg.
Desk will go down but up.
Check the area for any obstructions.
The desk is sliding down on its own.
Check if overloaded, max loading: 100kg.
Controls are unresponsive after lots of
use.
Disconnect the power and wait for 18mins before
re-connecting the power.
Not enough up & down height.
Press and hold the "M" and "3" buttons together
until you hear two beeps. This will restore factory
settings.
LED displays .
Press and hold the ▼button. The desk will move
into the lowest position and then reverses until it
comes to a stop. When the LED displays the
height number, release the ▼button.
If the desk doesn’t operate normally and the LED
displays “E01” or “E02” after the reset, check all
the cable connections, turn off the power outlet
for 10 seconds and try again in 18 minutes.
If it still doesn’t operate normally contact
help.Kogan.com
for support.
Disposal
This marking indicates that this appliance should not be disposed with other
household wastes. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote
the sustainable reuse of material resources.
TROUBLESHOOTING

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com.