Ergolux ELESTNDSKNA User manual

ELECTRIC STANDING
DESK
ELESTNDSKNA, ELESTNDSKBA & ELESTNDSKWA

• Read all instructions before use and retain this user guide for future reference.
• Read all following safety precautions carefully before use.
• Your equipment is intended for use in cool, dry conditi o n s . You should avoi d storage in
extreme cold, hot or damp areas as this may lead to corrosion and other related
problems.
• This desk is rated at a maximum weight capacity of 70kg.
• This desk is designed for indoor use only.
• Do not modify the desk frame or any of the components that operate this desk in any
way.
• If the power cord is damaged, cease use immediately and contact help.Kogan.com for
support.
• If the control box emits any abnormal noises or strong odours, cease use immediately
and contact help.Kogan.com for support.
• Ensure any obstacles are removed from the area around the desk during assembly and
operation.
• Ensure that all cords and wires are arranged in a way where they are not a tripping
hazard.
• Unplug the power cord before cleaning. Wipe the dust from the surface using a slightly
damp cloth. Ensure any water does not come in contact with any internal parts or
connectors.
• Do not disassemble or perform any maintenance without disconnecting the power first.
• Do not use any corrosive or abrasive materials to clean the product.
• The control box contains electronic components, metals, plastics, wires etc. ensure it is
disposed of in accordance with your local environmental legislation. Do not dispose
with general household waste.
• Ensure this product is completely and correctly assembled before use.
• Be familiar with all functions and program settings of the product before first use.
• This product can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
• Children should not be allowed play with this product.
• Cleaning and user maintenance should not be performed by children without
supervision.
• Retain the original packaging where possible, to use for any future transportation of this
product.
SAFETY & WARNINGS

Lay all components out on a clean floor and ensure all parts are included. If any pieces are
missing, check all packaging thoroughly, then contact help.Kogan.com for assistance.
ADesktop
BSync Rod
CLifting Column
DLifting Column
ESide Bracket (x2)
F Foot (x2)
GCrossbar (x2)
H Motor
IAC Adapter
J Controller
COMPONENTS

Hardware List
S-A M4x40
Phillips Head Screw (x4)
S-B M6x12 Hex
Head Screw (x22)
S-C M6x30 Hex
Head Screw
(x10)
S-D ST4.0x12
Phillips Head Screw
(x4)
To o l s R e q u i re d
4mm Allen key (included)
Spirit Level
Phillips Head Screwdriver

Step 1: Installing the feet.
• Attach the Feet (F) to the bottom of the Lifting Columns (C)(D) using x8 M6x30 Hex
Head Screws (C).
S-C (x8)
4mm Allen key
ASSEMBLY

Step 2: Attaching the Sync Rod
• Insert the end of the Sync Rod (B) without the notch though the Motor (H).
• Insert the Sync Rod (B) into the holes on the Lifting Columns (C)(D).
• Secure the motor in place using x2 M4x40 Phillips Head Screws (S-A).
S-A (x2)
Notch

Step 3: Attaching the Crossbars
• Attach the Crossbars (G) to the Lifting Columns (C)(D) using x8 M6x12 Hex Head
Screws (S-B).
Note: Ensure the screws are inserted into the outer most holes on the crossbars and
lifting columns.
S-B (x8)

Step 4: Attaching the Side Brackets
• Attach the Side Brackets (E) to the Lifting Columns (C)(D) using x4 M6x12 Hex Head
Screws (S-B).
Note: Ensure the Side Brackets are attached to the two holes second from the top of
the upper edge of the lifting columns.
S-B (x4)

Step 5: Attaching the Desktop
• Lay the Desktop (A) face down on a soft, flat surface (carpet, blanket etc.).
• Attach desk frame assembly to the Desktop (A) using x8 M6x12 Hex Head Screws
(S-B).
S-B (x8)
Step 6: Connecting the Controller
• Connect the AC Adapter (I) and the Motor (H) connectors to the mating connectors on
the Controller (J).
Note: Do not plug the AC Adapter into power until assembly is complete.
Blanket

Step 7: Attaching the Controller
• Attach the Controller (J) to the Desktop (A) using x2 ST4.0x12 Screws (S-D).
S-D (x2)

Step 8: Adjusting the Desk
• Turn the Desk back over to the upright position.
• Use a spirit level to ensure the desk is level and stable. Each foot has two adjustable
pads that can be rotated to raise or lower the desk.
CAUTION: To avoid serious injuries, at least two people are required
when turning the desk over.
Spirit level

Before First Use
When the desk is first powered on, the height will be displayed on the controller. If this
number does not match the actual height of the desk, the system will need to be reset
before use.
Resetting the System
1. Use the “ ” button to place the desk in the lowest position, then and press hold
the “ ” button for 7 seconds until the display is alternately flashing “RST” and
“E-1”. Release the “ ” button
2. Press and hold the “ ” button again, the desk will move downward slightly and
then move upwards approximately 5mm.
3. The system has now successfully been reset.
Note: To re s e t a d e s k w i t h a c u s t o m i s e d m i n i m u m h e i g h t , y o u w i l l n e e d t o p r e s s a n d h o l d
both the “ ” and “ ” buttons simultaneously.
Adjusting the Height
Press the “” or “ ” or buttons to adjust the height of the desk. The display will show
the current height.
OPERATION
Display
Raise
Lower
Memory
1/2/3
Settings

Memory Setting
1. To save a position to one of the three memory buttons, first adjust the desk to the
desired height.
2. Press the “S” button, the display will flash the current height then press either the
“1”, “2” or “3” button. The current height will be stored to the respective button.
3. To use one of the saved positions, press either the “1”, “2” or “3” button. The desk
will move to the saved position.
Switching Units (CM/INCH)
1. Press and hold the “S” button until “SET” is displayed.
2. Press “1” to enter the unit menu. The display will alternately flash “unt” and the
current height.
3. Press the “” or “ ” or buttons to switch the unit of measurement.
4. Press the “S” button to save your selection.
Collision Avoidance
1. Press and hold the “S” button until “SET” is displayed.
2. Press “2” to enter the collision avoidance menu. The display will alternately flash
“cpt” and the current sensitivity level.
3. Press the “” or “ ” or buttons to adjust the sensitivity level.
4. Press the “S” button to save your selection.
Controller Lock
1. Press and hold the “S” button until “SET” is displayed.
2. Press “3” to lock the controller. The display will flash “OFF”. Note: In this current
state any buttons pressed will have no effect.
3. Press and hold the “S” button for 3 seconds to unlock the controller.

Setting a Custom Minimum & Maximum Height Limit
1. Press and hold the “S” button until “HLP” is displayed.
2. The display will alternately flash “HLP” and the current height.
o Adjust the desk to your desired maximum height and press “1”. The display
will flash “H-P”, press “S” to store the height.
o Adjust the desk to your desired minimum height and press “2”. The display
will flash “L-P”, press “S” to store the height.
o Press “3” to remove the previously stored height settings.
Deleting Custom Settings
1. Press and hold the “S” button until “FAC” is displayed, then release the button.
2. Press the “S” button again to remove all custom settings.

The following tips will help you detected and eliminate some common faults and errors. If
the problem cannot be fixed or the fault is not listed below, please contact help.Kogan.com
for support.
Error Code
Solution
Err
The control panel is disconnected. Check the
connection. Disconnect the power then
reconnect it.
E-1
Reset the system.
E-2
The weight rating has been exceeded. Remove
all items from the desktop and reset the system.
E-3
The collision avoidance system has activated.
Remove all items within the desk’s range of
motion.
E-5
Check all connection and reset the system.
ovr
An overload has occurred. Remove all items
from the desktop and reset the system.
hot
The system has overheated. Remove all items
from the desktop and reset the system.
voL
An electrical fault has occurred. Disconnect the
power then reconnect it.
Disposal
This marking indicates that this appliance should not be disposed with other
household wastes. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote
the sustainable reuse of material resources.
TROUBLESHOOTING

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com