Ergotron LX Desk Dual Direct Arm User manual

1 of 14
888-45-352-G-02 rev. E • 09/17
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Deutsch
Benutzerhandbuch - Nederlands
Guida per l’utente - Italiano
Användarhandbok - svenska
ユーザーガイド : 日本語
用户指南 : 汉语
LX Desk Dual Direct Arm
Includes
Constant Force™
Technology
ENGLISH
For the latest User Installation Guide please visit: www.ergotron.com
User's Guide

2 of 14
888-45-352-G-02 rev. E • 09/17
WARNING
ENGLISH
These symbols alert users of a safety condi-
tion that demands attention. All users should
be able to recognize and understand the
significance of the following Safety Hazards
if encountered on the product or within the
documentation. Children who are not able
to recognize and respond appropriately to
Safety Alerts should not use this product with-
out adult supervision!
Hazard Symbols
Review
Symbol Signal Word Level of Hazard
NOTE A NOTE indicates important information that helps you
make better use of this product.
CAUTION
A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the
problem.
WARNING A WARNING indicates either potential for property dam-
age, personal injury, or death.
ELECTRICAL
An Electrical indicates an impending electrical hazard
which, if not avoided, may result in personal injury, re
and/or death.
Safety
Important! You will need to adjust this product after installation is complete. Make sure all your
equipment is properly installed on the product before attempting adjustments. This product should
move smoothly and easily through the full range of motion and stay where you set it. If movements
are too easy or difficult or if product does not stay in desired positions, follow the adjustment
instructions to create smooth and easy movements. Depending on your product and the adjustment,
it may take many turns to notice a difference. Any time equipment is added or removed from this
product, resulting in a change in the weight of the mounted load, you should repeat these adjustment
steps to ensure safe and optimum operation.
Warning:
Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong enough to
handle mounted product and equipment.
Caution:
To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow
these instructions may result in equipment damage or personal injury.
WARNING:
Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly,
on its own, as soon as attached equipment is removed. For this reason, DO NOT remove
equipment unless the arm has been moved to the highest position! Failure to follow this
instruction may result in serious personal injury and/or equipment damage!
CAUTION: DO NOT rotate
monitor past rear edge of desk.
Doing so will create an unstable
situation and may cause
equipment damage or personal
injury.

3 of 14
888-45-352-G-02 rev. E • 09/17
13"
(333mm)
< 11lbs. (5 kg)
< 11lbs. (5 kg)
360°
360°
180°
Portrait/Landscape Rotation
< 4.5” (114 mm)
8.5” (216 mm)
17°
13°
ENGLISH
Features & Specifications
CAUTION: DO NOT EXCEED
MAXIMUM LISTED WEIGHT
CAPACITY. SERIOUS INJURY
OR PROPERTY DAMAGE MAY
OCCUR!
* The lower most range of motion for vertical lift
may decrease up to 4.5”(114 mm) when arm is
adjusted to hold over 20lbs (9 kgs).

4 of 14
888-45-352-G-02 rev. E • 09/17
AB C D
1
2
3
4
1x
10mm
1x 1x
1x 2x 2x
1x
10x
M4 x 8mm
2x 3x
M4 x 6mm
5x 2x 2x
1x
10x
2.5mm
1x
M4 x 10mm
M4 x 10mm
4 mm
ENGLISH
Components
Tools Needed

5 of 14
888-45-352-G-02 rev. E • 09/17

C/L
(483mm)
19”
C/L
0.47" - 1.38" (12 - 35mm)
4mm
1.46" - 2.4" (37 - 60mm)
≤0.4" (10mm)
22.5mm
1x
ENGLISH

6 of 14
888-45-352-G-02 rev. E • 09/17
3
b
M4 x 8mm
1x
a
0°
M4x 6mm
1x
4
4x
M4 x 10mm 4x
M4 x 10mm
1x
M4 x 6mm
ENGLISH
Attach monitors to mounting brackets.Loosely thread thumb screws
into mounting brackets.
OPTIONAL: Insert stop screw
to lock portrait/landscape
monitor rotation.

7 of 14
888-45-352-G-02 rev. E • 09/17
5
6
aa
b
b
cc
2x
2x
ENGLISH
Slide monitor onto crossbar.

8 of 14
888-45-352-G-02 rev. E • 09/17
7
82x
M4 x 10mm 2x
M4 x 10mm
M4 x 8mm
2x
ENGLISH
Tighten thumb screws to secure monitors.

9 of 14
888-45-352-G-02 rev. E • 09/17
9
4x
ENGLISH
NOTE: Leave enough slack in cable to allow full range of motion.
Caution: To avoid the potential to pinch cables it is important to follow the cable routing
instructions in this manual. Failure to follow these instructions may result in equipment
damage or personal injury.

10 of 14
888-45-352-G-02 rev. E • 09/17
10
a
2x
10mm
ENGLISH
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or difficult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a difference. Any time
equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure safe and optimum operation.
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
Pivot adjustment.
Attach caps.
NOTE: Align slot on cap with slot in mounting bracket
when installing caps.