Ergotron Dual Monitor Tilt Pivot User manual

1 of 9
888-98-037-G-00 rev. C • 06/19
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语
Dual Monitor
Tilt Pivot
English
For the latest User Installation Guide please visit: www.ergotron.com

2 of 9
888-98-037-G-00 rev. C • 06/19
30°
3-11lbs.
(1.4-5kg)
30"
(705mm)
7.1" - 26"
(180mm) - (660mm)
Top View
13"
(330mm)
These symbols alert users of a safety condi-
tion that demands attention. All users should
be able to recognize and understand the
significance of the following Safety Hazards
if encountered on the product or within the
documentation. Children who are not able
to recognize and respond appropriately to
Safety Alerts should not use this product with-
out adult supervision!
Hazard Symbols
Review
Symbol Signal Word Level of Hazard
NOTE
A NOTE indicates important information
that helps you make better use of this
product.
CAUTION
A CAUTION indicates either potential
damage to hardware or loss of data and
tells you how to avoid the problem.
WARNING
A WARNING indicates either potential
for property damage, personal injury, or
death.
ELECTRICAL
An Electrical indicates an impending
electrical hazard which, if not avoided,
may result in personal injury, fi re and/or
death.
Features & Specifi cations
CAUTION: DO NOT EXCEED
MAXIMUM LISTED WEIGHT
CAPACITY. SERIOUS INJURY
OR PROPERTY DAMAGE MAY
OCCUR!

3 of 9
888-98-037-G-00 rev. C • 06/19
ABCD
1
2
2x
10mm
M4 x 8mm M4 x 6mm
M4 x 10mm
M4 x 10mm
2x 2x
2x 8x 8x
4x
2x
M4 x 5mm
Components
Tools Needed

4 of 9
888-98-037-G-00 rev. C • 06/19
1
a
b
c
Remove monitor pivots.

5 of 9
888-98-037-G-00 rev. C • 06/19
2
M4 x 10mm
4x
a
0°
M4x 6mm
1x
4x
M4 x 10mm
Install tilt pivots.
OPTIONAL: Insert stop
screw to lock portrait/
landscape
monitor rotation.

6 of 9
888-98-037-G-00 rev. C • 06/19
b
NOTE: Monitor mounting brackets
can be installed upside down to lower
monitor 4 1/4" (108 mm).
Center total width of mounted equipment
on stand.
NOTE: Installing mounting monitor brackets upside
down may restrict the full range of up/down motion.

7 of 9
888-98-037-G-00 rev. C • 06/19
c
34x
2x
M4 x 5mm M4 x 8mm
2x

8 of 9
888-98-037-G-00 rev. C • 06/19
4
a
10mm
52x
b
Adjustment Step
Adjust your mounting solution to handle the added weight.
Adjustments should move smoothly and easily through the full range of motion and stay where you set it. If adjustments
are diffi cult and do not stay in the desired position, follow the instructions to loosen or tighten the tension to create a
smooth, easy adjustment motion. Depending on your product and the adjustment, it may take several turns to notice a
diff erence.
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
Attach caps.
NOTE: Align slot on cap with
slot in mounting bracket when
installing caps.
Tilt – Forward and Backward
Adjust your mounting solution to handle the added weight.
Adjustments should move smoothly and easily through the full range of motion and stay where you set it. If adjustments
are diffi cult and do not stay in the desired position, follow the instructions to loosen or tighten the tension to create a
smooth, easy adjustment motion. Depending on your product and the adjustment, it may take several turns to notice a
diff erence.

9 of 9
888-98-037-G-00 rev. C • 06/19
© 2016 Ergotron, Inc. All rights reserved.
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
Learn more about ergonomic computer use at: www.ergotron.com/ergonomics
For local customer care phone numbers visit: http://contact.ergotron.com
For Service visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty
NOTE: When contacting customer
service, reference the serial number.