Ergotron Tablet Management Wall Mount 10 User manual

1 of 20
< 24lbs. (11 kg)
Reduce.Reuse.Recycle
Tablet Management Wall Mount 10
Includes Show & Stow™technology.
Show
&Stow
TM
ENGLISH
888-61-092-G-00 rev. D • 08/17
CAUTION: DO NOT EXCEED MAXIMUM LISTED
WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
Table of Contents
Hazard Symbols Review & Safety................................................2
Components & Tools...................................................................2
Mounting Considerations............................................................3
Set-up....................................................................................3 - 8
Wood Stud Attachment...........................................................4
Concrete Attachment...............................................................6
Cable Routing..............................................................................9
Charging and Syncing ........................................................17 - 18
Cleaning and Maintenance........................................................19
Specications............................................................................20
Service and Warranty Information ............................................20

2 of 20
AB C D
1
2
3
10mm
2
1
Ø 3/16" (5 mm) Ø 3/8" (10 mm)
Ø 1/2" (13 mm)
4x
5x
2x
1x
1x
1x
M4 x 8mm
PENTA
2x
M4 x 8mm
2x
1x
1/4”-20 x 2”
4x
M6 x 70mm
5x
1x
1x
1x
5/32”
ENGLISH
888-61-092-G-00 rev. D • 08/17
Components
Tools Needed
These symbols alert users of a safety condition that
demands attention. All users should be able to
recognize and understand the signicance of the fol-
lowing Safety Hazards if encountered on the product
or within the documentation. Children who are not
able to recognize and respond appropriately to Safety
Alerts should not use this product without adult
supervision!
Hazard Symbols Review Symbol Signal Word Level of Hazard
NOTE A NOTE indicates important information that helps you
make better use of this product.
CAUTION
A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the
problem.
WARNING A WARNING indicates either potential for property dam-
age, personal injury, or death.
ELECTRICAL
An Electrical indicates an impending electrical hazard
which, if not avoided, may result in personal injury, re
and/or death.
Safety
WARNING: Because surfaces vary widely and the ultimate mounting method is out
of Ergotron’s control, it is imperative that you consult with appropriate engineering,
architectural or construction professional to ensure that your Ergotron mounting
solution is mounted properly to handle applied loads.
CAUTION: Make sure the wall mount bracket
is level, ush and snug to the wall surface.
DO NOT OVERTIGHTEN THE BOLTS.
Stud Finder
WOOD CONCRETE

3 of 20
< 2.4 lbs
(1.1 kg)
< 10.2" (259 mm)
10” (254 mm)10" (254 mm)
43.2" (1098 mm)
< 7.9"
(201 mm)
< 0.9"
(23 mm)
24"
(610 mm)
5.6"
(142 mm)
4"
(102 mm)
60”-66"
(1524-1676 mm)
21.8"
(553 mm)
30.4"
(772 mm)
28.8"
(732 mm)
3"
(76 mm)
5.7"
(145 mm)
11.8"
(300 mm)
5.7”
(145 mm)
4"
(102 mm)
1
2
84
ENGLISH
888-61-092-G-00 rev. D • 08/17
Mounting Considerations
Maximum Tablet Size and Weight
(including case):
Space Requirements:
Minimum space needed when removing front cover (for
service access only).
If 24” (610 mm) is not available, unit can be removed from
the wall for service, if needed.
When mounting to wood stud, at least one screw in the upper mounting
bracket must be installed in a stud (preferably the center hole).
minimum space
needed on both sides
for removing tablets.
Mounting
Holes
Mounting
Hole
Worksurface
Recommended
Floor
Recommended Mounting Height
Above Floor
Recommended
Minimum
Mounting Height
Above Work-
surface
WOOD AND HOLLOW WALL CONCRETE

4 of 20
ab
c
60”-66"
(1524-1676 mm)
2
ENGLISH
888-61-092-G-00 rev. D • 08/17
Hole Option 1
RECOMMENDED
Center Hole in Stud
NOTE: The stud can be located at one of ve mounting holes on the top bracket. While the
rst option (center hole of bracket) is recommended for most cases, you should consult with a
construction professional to conrm which method is best suited for your particular situation.
Options 2-5 are illustrated on the following page in no order of preference.
WOOD AND HOLLOW WALL

5 of 20
6
d
60”-66"
(1524-1676 mm)
ENGLISH
888-61-092-G-00 rev. D • 08/17
STUD LOCATION OPTIONS 25
Extreme Left Hole in Stud
Middle Left Hole in Stud
Middle Right Hole in Stud
Extreme Right Hole in Stud
Hole Option 2
Hole Option 5
Hole Option 3 Hole Option 4

6 of 20
8
Ø 3/16"
(5 mm)
Ø 1/2"
(13 mm)
e
fg
M6 x 70mm
10mm
60”-66"
(1524-1676 mm)
1/4”-20 x 2”
12 3 4
1x
5/32”
ENGLISH
888-61-092-G-00 rev. D • 08/17
WOOD AND HOLLOW WALL
NOTE: Use the Ø 3/16” (5 mm) drill bit when drilling directly into the wood
stud.Use the Ø 1/2”(13 mm) drill bit when drilling into the hollow wall for the
anchors. Use hollow wall anchors where ever a screw does not get inserted
directly into the wood stud.
Drill the three holes in the top bracket that correspond with the hole option determined
on previous page. Then drill the two holes in the bottom bracket.
Attach brackets to wall according to the hole option determined
on previous page.
NOTE: Bottom Bracket mounting holes will always line up vertically with the
center mounting hole in the Top Bracket.
WOOD STUD
HOLLOW WALL

7 of 20
Ø 3/8"
(10 mm)
3-1/8"
(80 mm)
5x
a
cd
e
b
8
60”-66"
(1524-1676 mm)
60”-66"
(1524-1676 mm)
60”-66"
(1524-1676 mm)
5x M6 x 70mm
10mm
ENGLISH
888-61-092-G-00 rev. D • 08/17
CONCRETE
WARNING:
Anchors that are not fully set in solid concrete
will not support the applied load resulting in
an unstable, unsafe condition which could lead
to personal injury and/or property damage.
Consult a construction professional if you have
any doubt about what this means in regard to
your particular situation.
WARNING:
Mounting holes must be at least 3-1/8” (80mm) deep and must
be located within solid concrete, not mortar or covering material.
If you drill into an area of concrete that is not solid, reposition
mounting holes until both anchors can be fully inserted into solid
concrete!

8 of 20
3
6
4
5
a
b
M4 x 8mm PENTA
2x
M4 x 8mm
2x
1x
ENGLISH
888-61-092-G-00 rev. D • 08/17
Place wrench in Cable
Restraint and run power
cable through as shown.
NOTE: You can push up to 3
feet (1 m) of excess power cord
up into the unit for storage.

9 of 20
7
ab c
Unplug from wall outlet. Remove front cover and save the
screws for reattachment.
Unlock and open door. Remove
the key to keep door unlocked
during service.
ENGLISH
888-61-092-G-00 rev. D • 08/17
USB Cable Routing

10 of 20
8Plug USB cable into slot 5 on the USB box.
aOpen door, Plug USB end of cable into USB box
and route the cable through the two clips as shown. bClose door and push plug through hole in side panel.
cOpen door and pull cable through side panel
and secure in the shown cable restraint leaving
4"-4.5" (102-114 mm) of slack.
dClose door and route cable
through cable clips. eStow excess cable in location shown.
NOTE: Open door
before routing
cable to make sure
you have enough
slack for door to
open and close.
ENGLISH
888-61-092-G-00 rev. D • 08/17