Erickson 07451 User manual

Item no: 07451
Arched Aluminum Loading Ramp
To avoid personal injury and/or property damage, please read and follow
ALL instructions before assembling and operating.
1. Never overload ramps. Maximum capacity for your ramp is 750 lb.; 1500 lb. per pair
(Evenly distributed load).
2. Always use safety strap to securely fasten the ramp to the vehicle. This prevents the ramp from
slipping off the back of the truck.
3. Carefully roll or winch equipment up or down the ramp. Never drive or ride your equipment while loading or
unloading. Erickson Manufacturing is not responsible for any damage or injuries that can
occur when loading and un-loading. USE AT YOUR OWN RISK!
4. Make sure the ramp is aligned with the wheels of the equipment being loaded or unloaded.
5. Always load or unload on a solid, level and stable surface with the vehicle in gear, the parking/
emergency brake on, and engine off.
6. Use as a loading ramp only.
7. Ramp surfaces must be clean, dry and free from oil, grease or water.
8. Maximum recommended height is 30 inches.
9. Inspect ramp before each use. Tighten any loose hardware. Replace any worn or damaged parts.
Replace safety strap if webbing is frayed or worn. Do not attempt to use a ramp that is damaged
in any way. No modification, alteration, or deviation to the ramp are authorized by the manufacturer.
Proper care and maintenance of the ramp are essential to safety.
10. Proper use of this product is critical to safety, and beyond the control of Erickson Manufacturing
Ltd. Erickson Manufacturing Ltd. neither guarantees nor is liable for any damage resulting from
improper use.The liability of this product is limited to its purchase price if it proves to be defective
in material and/or workmanship.
IMPORTANT NOTICE ABOUT LOADING ON A TAILGATE
• Erickson Manufacturing does not recommend the loading or
unloading of equipment on a tailgate.
• It is recommended that if you choose to load or unload using a
tailgate that you take the proper precautions and support your
tailgate with a approved Tailgate Support.
• For more information visit www.dgmtailgatesupport.com

Item no: 07451
Specifications
Usage
Step 1 Be sure you are loading on a hard, level and stable surface and that the vehicle you are loading
into is parked with the emergency/parking brake in “Park” and the engine is “off”. Unfold and place the
lip of the ramp against the back of the vehicle.
Step 2 Secure the ramp to the vehicle using the adjustable strap. After the strap is secure, test the
ramp by pulling backwards on it. Make sure it does not slide back or disengage from the
loading surface.
Step 3 Once the ramp is secure and the area is safe to proceed with loading, move the vehicle to be
loaded between the ramps and center the load between both ramps.
Step 4 Proceed with loading the vehicle, making sure the ramp is sustaining the load and not
bowing from weight.
Step 5 Continue until the vehicle is fully loaded. Secure the brake and tie down as needed.
Step 6 Unhook the adjustable strap and fold the ramp and lock into the folded position. Store in a
clean, dry and safe place where damage will not occur.
Rated Capacity SINGLE RAMP 750 lb. (distributed load)
PAIR OF RAMPS 1500 lb. (distributed load)
90” x 12” (228 cm x 30 cm)
Ramp Dimensions
2 WHEELS EVENLY
DISTRIBUTED
WHEN USING A SINGLE OF RAMP
MAXIMUM
1500 lb.
(680 kg)
4 WHEELS EVENLY DISTRIBUTED
WHEN USING A PAIR OF RAMPS
MAXIMUM
750 lb.
(340 kg)

Item no: 07451
Warranty
Warranty Qualifications
Effective from the day you purchase the product. Please keep your dated purchase invoice as proof.
Repair/Replacement Warranty
Erickson Manufacturing Ltd. warrants to the original purchaser that the mechanical components
will be free of defect in material and workmanship for 90 days from the original date of purchase.
Transportation charges on product submitted for repair or replacement under warranty are the
sole responsibility of the purchaser.This warranty only applies to the original purchaser and is
not transferable.
Do Not Return The Unit to the Place of Purchase
Contact Erickson Manufacturing Ltd’sTechnical Service and service people will troubleshoot any
issue via phone or email. Repairs or replacements without prior authorization, or at an unauthorized
repair facility, will not be covered by this warranty.
STRAP MUST
BE TIGHT

Item no: 07451
Warranty Exclusions
This warranty does not cover the following repairs and equipment:
Normal Wear
This warranty does not cover the repair when use has exhausted the life of a part or the equipment
as a whole.
Installation, Use and Maintenance
This warranty will not apply to parts and/or labor if this product is deemed to have been misused,
neglected, involved in an accident, abused, loaded beyond specifications, modified, or installed
improperly. Normal maintenance is not covered by this warranty.
Other Exclusions
This warranty excludes:
• Cosmetic defect such as paint, decal etc.
• Wear items
• Accessory parts
• Failures due to acts of God and other force majeure events beyond the manufacturer’s control.
• Problems cause by parts that are not Erickson Manufacturing Ltd. parts.
Limits of implied Warranty and Consequential Damage
Erickson Manufacturing Ltd. disclaims any obligation to cover any loss time, use of this product, freight,
or any incidental or consequential claim by anyone from using this product.THIS WARRANTY IS IN LIEU
OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. A unit provided as exchange will be subject to the warranty
of the original unit. The length of the warranty governing the
exchanged unit will remain calculated by reference to the purchase date of the original unit.This
warranty gives you certain legal rights which may change from state to state.Your state and/or
province may also have other right you may be entitled to that are not listed within this warranty.
Contact Information
Marine City, Michigan 48039
Thamesville, Ontario N0P 2K0
Toll Free: 1-888-546-4668