ERICO CADDY CPNAM Series User manual

TECHNICAL SUPPORT:
www.erico.com
CFS434_C
WARNING:
1. ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at
www.erico.com and from your ERICO customer service representative.
2. ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
3. All instructions must be completely followed to ensure proper and safe installation and performance.
4. Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property
damage, serious bodily injury and death.
5. Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
6. All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
other purpose.
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
©2010, 2015 ERICO International Corporation1 OF 4
CPNAM Series
Decking Offset Clips and Box / Conduit Hangers
Part Number
6MCPNAM
812MCPNAM
16MCPNAM
20MCPNAM
24MCPNAM
Part Number
CD0BCPNAM
CD1BCPNAM
CD2BCPNAM
CD2.5BCPNAM
Part Number
CPNAM
Part Number
6MB18CPNAM
812MB18CPNAM
16MB18CPNAM
Part Number
B18SBT18CPNAM

TECHNICAL SUPPORT:
www.erico.com
CPNAM Series
Decking Offset Clips and Box / Conduit Hangers
Hardware not included
CFS434_C ©2010, 2015 ERICO International Corporation2 OF 4
Static Load Limit 100 lbs [450 N]
Note: Static load limits apply to
CADDY fasteners only
R
Part Number
CPNAM

TECHNICAL SUPPORT:
www.erico.com
CPNAM Series
Decking Offset Clips and Box / Conduit Hangers
Part Number
6MCPNAM
812MCPNAM
16MCPNAM
20MCPNAM
24MCPNAM
Part Number
CD0BCPNAM
CD1BCPNAM
CD2BCPNAM
CD2.5BCPNAM
Step 1 Step 2 Step 3
Step 1 Step 2
CFS434_C ©2010, 2015 ERICO International Corporation3 OF 4
Static Load Limit 100 lbs [450 N]
Note: Static load limits apply to
CADDY fasteners only
R
Static Load Limit 100 lbs [450 N]
Note: Static load limits apply to
CADDY fasteners only
R

TECHNICAL SUPPORT:
www.erico.com
CPNAM Series
Decking Offset Clips and Box / Conduit Hangers
Part Number
B18SBT18CPNAM
Step 1 Step 2
Step 2 - Install conduit in box.
Step 3 - Finger snap clips
closed around conduit.
Part Number
6MB18CPNAM
812MB18CPNAM
16MB18CPNAM
Step 1 - Attach box with self
tapping screws (SMS8).
CFS434_C ©2010, 2015 ERICO International Corporation4 OF 4
Static Load Limit 50 lbs [225 N]
(Includes conduit and box)
Note: Static load limits apply to
CADDY fasteners only
R
Static Load Limit 50 lbs [225 N]
(Includes conduit and box)
Note: Static load limits apply to
CADDY fasteners only
R
*See additional assembly instructions
below in steps 1 - 3