Erskine Attachments 68 User manual

Angle Broom
For
Skid Steer Loaders
Operator’s Manual
Set-Up Assembly
Maintenance
Parts Information
Read this Manual Before Use

2
TABLE OF CONTENTS
REFERENCE INFORMATION
Write the serial number for your attachment in the spaces below. Always refer to this serial
number when calling for service or parts.
Serial Number………….._____________
YOUR ATTACHMENT DEALER
ADDRESS:
PHONE:
CONTACT:
SAFETY
3-4
SERIAL NUMBER/DECAL LOCATION
5-6
USER’S MOUNTING INSTRUCTIONS
7-8
OPERATING INSTRUCTIONS
9-10
ROUTINE MAINTENANCE
11-13
SET-UP ASSEMBLY
14-16
PARTS INFORMATION
17-23
GENERAL SPECIFICATIONS
24
BOLT TORQUE INFORMATION
25
NOTES
26
WARRANTY
27
NOTE: Erskine Attachments LLC reserves the right to make
improvements in design or changes in specifications at any time without
notice and without incurring any obligations to install them on units
previously sold.

3
The signal words CAUTION, WARNING, or
DANGER are used to indicate hazards.
Indicates a potentially
hazardous situation which, if not avoided,
may result in minor or moderate injury.
Indicates a potentially
hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a potentially
hazardous situation which, if not avoided,
will result in death or serious injury.

The word IMPORTANT is used in the text when
immediate damage will occur due to improper
technique or operation.

The word NOTE is used to convey information that
is out of context with the manual text; special
information such as specifications, techniques,
reference information, and other information of a
supplementary nature.
The user is responsible for inspecting the machine
daily, and for having parts repaired or replaced when
continued use of the machine would cause damage,
excessive wear to other parts or make the machine
unsafe for continued operation.
If an operating procedure, tool device, maintenance
or work method not specifically recommended is
used, you must satisfy yourself that it is safe for you
and others. You must also ensure that the
attachment will not be damaged or made unsafe by
the procedures you choose.
Erskine Attachments LLC cannot anticipate every
possible circumstance that might involve potential
hazard. The safety messages found in this manual
and on the machine are therefore not all inclusive.
SAFETY
DO NOT use or perform maintenance on this machine until this manual has been
read and understood. In addition, read the Operation and Maintenance
Manual(s) pertaining to the attachment and the attachment carrier (“Loader”).

4
SAFETY
Improper operation can cause serious
injury or death.
Pre-operation
This machine is designed for small debris and
snow removal only. NEVER use this machine for
any other purpose.
Read the operator’s manual for the “Skid Steer
Loader.”NEVER allow untrained people to
operate.
Operating instructions must be given to everyone
before operating this attachment and at least once
a year thereafter in accordance with OSHA
regulations.
NEVER exceed the maximum recommended input
power or speed specifications for the attachment.
Over-powering or over-speeding the attachment
may cause personal injury and/or machine
damage.
Keep all shields, guards, and covers in place.
Do not modify equipment or add attachments that
are not approved by Erskine Attachments LLC.
Use adequate safety warning lights and devices as
required by local regulations. Obey all local laws
and regulations regarding machine operation on
public property.
Operation
Always wear eye protection that meets ANSI z87.1
standard or use with a loader enclosure that
provides similar protection.
Hydraulic connections may be hot after use. Use
gloves if connecting or disconnecting after use.
Check and be sure all operating controls are in
neutral before starting the engine.
Keep people away from loader, attachment and
discharge when in use. This attachment sends
objects flying and has rotating parts. NEVER direct
discharge toward people –rocks and debris canbe
thrown.
Depending on how this attachment is used, dust
can be created. Prolonged exposure to dust can
cause chronic and acute health problems. A
NIOSH-approved respirator may be required.
Operation (continued)
NEVER operate near embankments or terrain that
is so steep that rollover could occur.
Always stay in the operator position when using
the attachment.
Before leaving the operators position, disengage
hydraulic drive, lower the attachment to rest flat on
the ground, stop engine, set park brake, and wait
for all motion to stop.
NEVER place hands in the discharge area or clear
debris while engine is running.
Avoid High Pressure Fluids Hazard
Escaping fluid under pressure can
penetrate the skin causing serious
injury.
Avoid the hazard by relieving the
pressure before disconnecting
hydraulic lines.
Use a piece of paper or cardboard, NOT BODY
PARTS, to check for suspected leaks. Wear
protective gloves and safety glasses or goggles
when servicing or performing maintenance on
hydraulic systems.
If an accident occurs, see a doctor immediately.
Any fluid injected into the skin must be surgically
removed within a few hours or gangrene may
result.
Maintenance
NEVER make adjustments, lubricate, clean, or
perform any service on the machine while it is in
operation.
Make sure the attachment is serviced on a daily
basis. Improper maintenance can cause serious
injury or death in addition to damage to the
attachment and/or your equipment.

5
SERIAL NUMBER AND SAFETY DECAL LOCATIONS
Serial Number Location:
It is important to refer to the serial number of the attachment when making repairs or ordering parts. Early or later
models (identification made by serial number) may use different parts, or it may be necessary to use different
procedures in doing a specific operation.

6
Part number: 202153 (Anti-skid tape 2x16)
Location: On pivot frame, right side
Quantity: 1
Part number: 200001
Location: On back of hood near tubelines
Quantity: 1
Part number: 203234
Location: On top of rear tube, both sides
Quantity: 2
SERIAL NUMBER AND SAFETY DECAL LOCATIONS________
Brand Decals
Location: On front of hood (Large)
Location: On each endplate (Small)
Quantity: 1 (Large)
Quantity: 2(Small)
Safety Decals Locations:
The locations of the safety decals are shown. If
these decals are missing, damaged, or painted over
they must be replaced. Call Erskine Attachments
LLC (218-435-4045) for replacement decals.
B
A
C
D
Part number: 320025
Location: On rear corner of frame, both sides
Quantity: 2
Part number: 316078
Location: On back of hood
Quantity: 1
E
F
Part number: 202152 (Anti-skid tape 2x8)
Location: On pivot frame, right side
Quantity: 1

7
USER’S MOUNTING INSTRUCTIONS
After the initial set-up assembly is completed use the following procedure to mount the attachment to the loader
for user operation. Coupler wedges or pins must extend through the holes in the attachment.
Levers must be fully down and locked. Failure to secure wedges or pins can allow the
attachment to come off and cause injury or death.
1. Use the step, safety treads, and grab handles to
get on and off the loader and attachment.
2. Sitting in the operator’s seat, lower seat bar (if so
equipped) and fasten the seat belt.
3. Drive the loader to the rear of the attachment. Put
the loader quick attach coupler into theattachment
mounting bracket.
4. Tilt the loader coupler backward a small amount
until it is fully engaged in the attachment mounting
bracket.
5. Stop the engine and engage the park brake.
6. Secure the coupler locking mechanism that
attaches the attachment to the loader.

8
USER’S MOUNTING INSTRUCTIONS
7. Connect the hydraulic quick couplers from the
attachment to the loader.
IMPORTANT: Wipe the ends of the hydraulic
quick couplers (both lead and loader) with a rag
to remove any possible contamination.
Contamination can cause hydraulic components
to fail and is not covered under warranty.
IMPORTANT: Make sure the quick couplers are
fully engaged. If the quick couplers do not fully
engage, check to see that the couplers are the
same size and brand. Do not force the quick
couplers together.
NOTE: See the loader’s operator’s manual for
auxiliary hydraulic specifications and connection
instructions.
NOTE: Attachment is shipped with 12FJX
(1-1/16” Female JIC Swivel) fittings on the ends
of the lead hoses.
8. Connect the attachment wire harness to the
loader’s wire harness receptacle. (Disregard if
pistol grip controller is supplied with the
attachment.)
9. Make sure the hoses are properly routed to fit
your specific loader. If the hoses are not routed
correctly, hoses may get pinched or rub on tires.
Be sure to check the hose routing through the full
range of intended motion of the attachment
before operating it.
More than one routing may be acceptable
depending on the loader. Pick the routing that
best suits your loader.
IMPORTANT: Proper hose routing is the
responsibility of the owner and/or operator.
Pinched or stretched hoses are not covered
under warranty.
Mounting is now complete and you are ready to use
the attachment. Use reverse order of above
instructions to dismount the attachment from the
loader.

9
OPERATING INSTRUCTIONS
Parking Stand
IMPORTANT: Before operation, make sure the
parking stands have been secured in the operating
position.
1. With the operator in the seat of the loader, the
seatbelt fastened, and the seat bar lowered (if so
equipped), start the engine.
2. With the loader arms fully lowered, position the
attachment flat on the ground. Engage the
auxiliary hydraulics in continuous flow mode to
start the bristle rotation, and drive the loader
forward to sweep.
NOTE: Broom rotation should always be such
that the material is swept away from the operator.
3. The torsion suspension will keep the down
pressure on the broom consistent, which allows
the broom to float. If more or less down pressure
is required, pressure can be adjusted by tilting the
attachment forward or back.
IMPORTANT: Excessive down pressure will
cause premature bristle wear or breakage.
NOTE: The down pressure on the broom
determines thebroom contact area onthe surface,
or the length of bristle contact with the surface.
Use the correct down pressure for the situation.
For dirt and debris removal, a 2.0 to 4.0 inch
contact area is recommended. This allows the
bristle tips to dig, break up, and throw material.
For snow removal, a 4.0 to 6.0 inch contact area
is recommended.

10
OPERATING INSTRUCTIONS
Attachment Control
System
Pistol Grip Controller
Manual Angling of the Attachment
Avoid manually adjusting the
broom angle while parked on sloped surfaces.
Removing the angle pin while parked on sloped
surfaces can cause the broom to move on its
own due to gravity. If it is necessary to adjust
the angle on a sloped surface, approach the
angle pin from the uphill side.
1. Park the loader and attachment on a flat, level
surface.
2. With the loader arms fully lowered, tilt the
attachment back until the broom bristles are
slightly off the ground.
3. Disengage the hydraulic drive, stop the engine,
engage the park brake, and wait for all motion to
stop.
4. Remove the clip pin and angle pin from the pivot
frame.
5. Manually push or pull on one end of the broom
to change the angle as desired.
6. Reinstall the pin and clip pin in the pivot frame.
Hydraulic Angling of the Attachment
1. With the operator in the seat of the loader, the
seatbelt fastened, andthe seat bar lowered (if so
equipped), start the engine.
2. Engage the auxiliary hydraulics in continuous
flow mode to start the bristle rotation.
3. Use the pistol grip controller or the loader’s
attachment control system (if equipped) to
activate the valve on the attachment and angle
the broom to the left or right as desired.
NOTE: See loader’s operator’s manual for
instructions on operating the attachment control
system.

11
ROUTINE MAINTENANCE
Lower the attachment to rest on the parking stands, shut down the engine, relieve the
hydraulic pressure to the attachment, set the park brake, and wait for all motion to stop before leaving
the operator’s seat to perform service of any kind.
It is the operator’s responsibility to make daily inspections of the loader and attachment for damage, loose bolts,
fluid leaks, or anything else that could cause a potential service or safety problem. Preventive maintenance is
the easiest and least expensive type of maintenance.
IMPORTANT: Bolts and set screws can loosen after initial usage. After the first hour of operation check all bolts
and set screws.
[A]
[B]
Use No. 2 lithium base gun grease when lubricating
all attachment grease fittings.
Grease the pivot bushing zerk [A] every 8 hours of
operation.
Grease the bearing mount zerk [B] every 80 hours of
operation.
IMPORTANT: Do not over-grease bearing. Only add
two pumps of grease every greasing interval.
8
No. 2 Lithium
base gun grease
Clean engine oil
LUBRICATION
80

12
ROUTINE MAINTENANCE
Replacing Brush Sections
1. Use the snapper pins to lock both parking stands
in the parking position.
2. Lower the attachment to rest on the parking
stands.
3. Remove the four bearing mount bolts and nuts.
4. Remove the four motor mount bolts and nuts.
5. Carefully remove the brush head assembly by
sliding the brush head forward and out of the
frame, then sliding the motor assembly out of the
end of the brush arbor.
6. Remove the three bolts holding the brush retainer
to the brush arbor.
7. Remove the old brush sections by sliding them off
of the arbor.

13
ROUTINE MAINTENANCE
8. Number the ribs on the arbor as 1, 2, and 3.
9. Slide the first “wavy” brush section on so that the
pins are around rib 1.
10. Slide the second “wavy” brush section on so that
the pins are around rib 2.
NOTE: Every other brush section will need to be
flipped so that the high spots of the bristle “waves”
on the neighboring sections hit each other.
11. Slide the third “wavy” brush section on so that the
pins are around rib 3.
12. Continue this pattern until all brush sections are
installed.
NOTE: The brush stack does not need to be flush
with the end of the arbor. It may be higher or lower
depending on how each brush section is formed.
If the stack is high, compress it when reinstalling
the brush retainer. If the stack is low, it will spread
out when the arbor is laid down. If the stack is
excessively high, remove one or more sections to
get it close to the proper height.
13. Reinstall the brush retainer and three bolts.
14. Slide the motor assembly into the end of the arbor,
aligning the hex drive with the hole in the end of
the arbor.
15. Slide the brush head assembly back into the
frame.
16. Reinstall the four motor mount bolts and nuts.
17. Reinstall the four bearing mount bolts and nuts.
18. Tighten all hardware to the proper torque(s).
Refer to “Bolt Torque Information” on page 25 of
this manual.

14
SET-UP ASSEMBLY
Set-Up from Shipping
1. Remove the straps holding the attachment to the
pallet.
2. Remove the six bolts and nuts attached to the
torsion frame.
3. Position the torsion frame so that the holes are
aligned with the holes in the sides of the pivot
frame.
NOTE: Blocks may be needed to raise up the
pivot frame. Use a hoist when lifting the pivot
frame.
4. Install the six bolts connecting the torsion frame
to the pivot frame.
5. Tighten the six bolts and nuts to the proper
torque. Refer to “Bolt Torque Information” on
page 25 of this manual.

15
Cable Tie
Hose Clamp
SET-UP ASSEMBLY
Wire Harness Installation
NOTE: If the loader is equipped with an attachment
control package, the appropriate harness should be
installed from the factory.
If the attachment was ordered with the pistol grip
control harness, follow these instructions:
1. Install the control handle on either steering lever,
whichever you prefer, with hose clamps.
NOTE: The control handle bracket can be
positioned several different ways. We
recommend it be positioned as shown.
2. Put a cable tie around the wiring harness and the
steering lever.
3. Install the wiring harness receptacle bracket on
either the loader arm or near the hydraulic quick
couplers.
NOTE: It may be necessary to make an adapter
bracket in order to attach the wire harness to the
loader.
4. Route the wiring harness back along the tube
lines on the loader arms and fasten with cable
ties.
5. Open the rear door. Pull the excess wiring
harness into the engine compartment.
6. Raise the operator cab. (See loader’s operator’s
manual for the correct procedure.)

16
SET-UP ASSEMBLY
7. Connect the red fused wire to the positive battery
terminal or to a suitable accessory wire with a
minimum rating of 5 amps. Route the wiring
along the loader main frame toward the front of
the loader.
Connect the black wire from the harness to a
frame ground.
8. Fasten the control handle wiring harness
connector to the main wiring harness connector.
IMPORTANT: Secure the wiring harness in
place with plastic cable ties, making sure it is
clear of extra hot areas or any moving parts on
the engine or loader. Pinched, stretched, or
melted wire harnesses are not covered under
warranty.
9. Lower the cab. (See loader’s operator’s manual
for the correct procedure.)
NOTE: Be sure the control handle wiring
harness is properly positioned as the cab is
lowered.

17
4
1
3
2
WIRE HARNESS PARTS INFORMATION
REF.
PART NO.
DESCRIPTION
QTY.
315128
COMPLETE HARNESS –generic (shown)
…………………………………...
1
1
315110
PISTOL GRIP –handle assembly w/ harness ………………………………..
1
2
315126
LOADER HARNESS –assembly ………………………………………………
1
3
202489
RECEPTACLE BRACKET –loader harness
………………………………….
1
4
315127
ATTACHMENT HARNESS –assembly ……………………………………….
1
Optional Harnesses (not shown)
PART NO.
DESCRIPTION
315090
14-PIN UNIVERSAL –for Bobcat® Loaders
315152
14-PIN UNIVERSAL –for Case® Loaders
320084
14-PIN UNIVERSAL –for John Deere® Loaders
200008
8-PIN –for Caterpillar® Loaders
315153
8-PIN –for ASV® Loaders
315339
8-PIN –for Caterpillar® B-Series High-Flow Loaders

18
PARTS INFORMATION
ITEM
QTY
PART NO.
DESCRIPTION
STOCK NO.
1
1
316001
MOUNT PLATE AB W/A
(NEW STYLE S/N BREAK 1045640)
1.1
1
422100
MOUNT PLATE AB EURO W/A
FOR EURO MOUNT ONLY
1.2
1
422183
MOUNT PLATE AB MULTIHOG W/A
FOR MULTIHOG MOUNT ONLY
2
1
316002
FRAME PIVOT AB W/A
3
1
316065
FRAME MAIN AB 68 W/A
1
316003
FRAME MAIN AB 84 W/A
1
316127
FRAME MAIN AB 96 W/A
4
1
316006
BRACKET MOUNTING LH W/A
5
1
316063
BRACKET MOUNTING RH W/A
6
1
316016
SPRING TORSION ASSY
7
2
316061
JACKSTAND W/A
8
1
316046
SHIELD SIDE LH PAINTED
9
1
316047
SHIELD SIDE RH PAINTED
10
1
316068
SHIELD BROOM 68 PAINTED
1
316049
SHIELD BROOM 84 PAINTED
1
316122
SHIELD BROOM 96 PAINTED
16
1
316045
PIN 1.5 X 6.25 W/A
20
1
320235
PIN HITCH 3/4 X 6
MANUAL ANGLING
21
2
300581
PIN SNAPPER 5/16 X 3
22
1
200064
PIN CLIP #11 1/8 X 2 5/8
MANUAL ANGLING
25
16
37337
NUT FLG TOP-LOCK
1/4 NC
26
2
13103
BOLT HEX
3/8 X 3/4 NC GR 5
30
2
316026
PIN 1 X 5 W/A
HYDRAULIC ANGLING
35
1
13107
BOLT HEX
3/8 X 1 1/4 NC GR 5
36
8
33626
WASHER LOCK
1/2"
39
10
13207
BOLT HEX
1/2 X 1 1/4 NC GR 5
42
8
37214
NUT REV LOCK
1/2 NC
47
16
21801
BOLT CARRIAGE
1/4 X 3/4 NC GR 5
48
**
32467
BOLT FLG THRD RLNG 3/8 X 3/4 NC GR5
** (6) 68" (8) 84" (8) 96”
49
2
316055
CLAMP TUBELINE 5/8
50
2
316094
CLAMP TUBELINE TOP PLATE 5/8
51
2
13061
BOLT HEX
5/16 X 2 NC GR 5
52
4
13309
BOLT HEX
5/8 X 1-1/2 NC GR 5
53
4
37216
NUT REV LOCK
5/8 NC

19
PARTS INFORMATION

20
PARTS INFORMATION
ITEM
QTY
PART NO.
DESCRIPTION
STOCK NO.
316083
PKG WAFER 68 POLY
35 CONV
316084
PKG WAFER 68 POLY/STEEL
35 CONV
316085
PKG WAFER 68 STEEL
35 CONV
316086
PKG WAFER 84 POLY
44 CONV
316087
PKG WAFER 84 POLY/STEEL
43 CONV
316088
PKG WAFER 84 STEEL
44 CONV
316129
PKG WAFER 96 POLY
50 CONV
316130
PKG WAFER 96 POLY/STEEL
49 CONV
316131
PKG WAFER 96 STEEL
50 CONV
11
1
316005
MOUNT MOTOR AB W/A PNT
12
1
316011
BRG 1-1/4 SM 4-B FLG
13
1
316066
ARBOR AB 68 W/A
1
316004
ARBOR AB 84 W/A
1
316128
ARBOR AB 96 W/A
14
1
316032
DRIVE BLOCK HEX 1.25" BORE
SNAP RING INCLUDED
15
1
300419
KEY 5/16 X 1-1/4
17
2
316091
WAFER AB STR STEEL 32
OBSOLETE NO LONGER USED
2
316089
WAFER AB STR POLY/STEEL 32
2
316041
WAFER AB STR POLY 32
18
* *
316092
WAFER AB CONV STEEL 32
(35) 68" (44) 84" (50) 96”
* *
316092
WAFER AB CONV STEEL 32(IN POLY/STEEL PKG)
(17) 68” (21) 84” (24) 96”
* *
316090
WAFER AB CONV POLY/STEEL 32
OBSOLETE NO LONGER USED
* *
316042
WAFER AB CONV POLY 32
(35) 68" (44) 84" (50) 96”
**
316042
WAFER AB CONV POLY 32 (IN POLY/STEEL PKG)
(18) 68” (22) 84” (25) 96”
19
316072
WAFER AB SPACER (INCLUDED WITH FLAT WAFER)
OBSOLETE NO LONGER USED
23
1
313333
RING SNAP EXT 2 X .063
25
16
37337
NUT FLG TOP-LOCK
1/4 NC
26
2
13103
BOLT HEX
3/8 X 3/4 NC GR 5
27
2
202830
WASHER LARGE 3/8 X 1 3/4
31
1
316050
PLATE WAFER KEEPER PAINTED
32
5
103880
WASHER LOCK
3/8"
33
5
103116
BOLT HEX
3/8 X 1 NC GR 5
36
8
33626
WASHER LOCK
1/2"
37
4
13209
BOLT HEX
1/2 X 1-1/2 NC GR 5
38
2
13210
BOLT HEX
1/2 X 1-3/4 NC GR 5
42
8
37214
NUT REV LOCK
1/2 NC