ESAB PREST-O-LITE 21820 User manual

INSTRUCTIONS for F-15-272
January, 2001
Be sure this information reaches the operator.
You can get extra copies through your supplier.
PREST-O-LITE®
R-511LPG FUEL GAS REGULATOR
P/N 21820
SPECIFICATIO S
Gas Service ..................................................................................... FG-2, propane, MAPP*
Inlet Connection ..................................................................................................... CGA- 10
Outlet Connection .......................................................................... CGA-021 (3/8"  24LH)
Delivery Pressure Range ..................................................................................... 0 - 4 psig
Flow Capacity ...................................................................................................... 0 - 130 cfh
Gauges: Cylinder Pressure ....................................................................................... None
Delivery Pressure ........................................................... 1-1/2-in. dia.; 0 - 60 psi
These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the principles of operation and safe prac-
tices for oxy-fuel gas e uipment, we urge you to read our booklet Precautions and Safe Practices for Welding, Cutting, and
Heating, Form 2035. Do NOT permit untrained persons to operate this e uipment. Do NOT attempt to operate this e uipment
until you have read and fully understand these instructions. If you do not fully understand these instructions, contact your
supplier for further information.
The regulator covered by these instructions is listed by Underwriters Laboratories only when used in combination with parts
manufactured by ESAB Welding & Cutting Products to the specifications on file with Underwriters Laboratories, Inc., and when
they are used in the gas service for which they are designed and listed. The use of other parts that cause damage or failure to the
e uipment will void the manufacturers warranty.
CO ECTI G:
1. Before attaching the regulator to a tank (cylinder)
open the tank valve slightly, for an instant, then close
it. This will blow out any dust or dirt which may be in
the valve outlet. Never open the tank valve near hot
work, a spark creating device, or any other possible
source of ignition.
2. Attach the regulator to the tank valve. Tighten the
connection nut with a wrench.
3. Attach hose with correct fittings to the regulator out
let and to the torch or other appliance. (All fuel gas
hose connection nuts have left hand threads.)
Tighten the connection nuts with a wrench.
4. Make sure the shutoff valve on your torch or other
appliance is closed. Then open the tank valve about
one quarter turn. When opening the tank valve, al
ways stand to one side of the regulator, not in front
of the gauge face.
*Registered trademark of Air Reduction Co.
TESTI G FOR LEAKS:
1. Turn the pressure adjusting screw on the regulator
to the right (clockwise) until the delivery pressure
gauge shows at least 40 psi pressure. Using a thick
solution of soap and water, applied with a small
brush, test for leaks at the tank valve, regulator con
nections, hole on top of pressure adjusting screw,
and torch or appliance connection. If you find a leak,
correct it before continuing. (A leak around the stem
of a fuel gas tank valve can often be corrected by
tightening the valve packing nut with a wrench. If
this will not stop the leak, remove the tank, tag it to
indicate valve stem leakage, and place it outdoors
in a safe spot until you can return it to your supplier.)
If there is a leak at the vent hole at the top of the
pressure adjusting screw, DO NOT USE THE
REGULATOR. Immediately remove it from the cyl
inder and return it to your PREST O LITE dealer or
to an ESAB welding equipment distributor to be re
paired.

any possible source of ignition. Accumulations
of gas in certain proportions may explode if ig-
nited.
2. EVER store LFG tanks (cylinders) in a closed
or confined space, such as a closet, tool box, or
automobile trunk.
3. EVER solder a container that contains or has
contained flammable liquids or vapors (includ-
ing gasoline, benzene, solvents, and similar
materials) unless the container has been thor-
oughly purged of all traces of flammable mate-
rial and vapors.
4. Before starting work always test for leaks around
all joints with a soapy water solution.
5. EVER use a flame to test for leaks of flammable
gases.
6. EVER use a tank with a leaking valve.
7. DO OT attempt any repairs to an LFG tank, ex-
cept to tighten the packing-gland nut on the
valve.
8. DO OT abuse or drop tanks or handle them
roughly.
9. EVER use a tank as a roller or support.
10. EVER use a hammer, wrench, or pliers on an
LFG tank valve which is fitted with a handwheel.
11. EVER allow full tank pressure to enter the hose.
Always use a regulator when there is a needle
valve on the torch handle.
12. EVER lay a torch down unless the gas flow has
been shut off. If you want to maintain a pilot
flame when you stop work for short intervals,
provide a rack or stand for the torch, away from
combustible materials. Do not leave it unat-
tended unless you are sure there is no danger
of its being disturbed by unauthorized persons.
13. Examine your hose for leaks frequently. Dipping
it in a bucket of clean water, with the pressure in
the hose, is the quickest and easiest way.
14. DO OT use hose that is worn, or any equip-
ment that is in need of repairs.
15. DO OT start fires. Be very careful when work-
ing near combustible material.
16. Fuel gas tanks (cylinders) are equipped with fus-
ible-metal safety devices. EVER store tanks
near radiators, furnaces, or other heat sources.
PREST-O-LITE is a registered trademark of ESAB Welding & Cutting Products
F-15-272 1/2001 Printed in U.S.A.
SETTI G WORKI G PRESSURE:
1. Open the torch or appliance valve and then quickly
reset the regulator to deliver gas at the desired work
ing pressure by turning the pressure adjusting screw
(clockwise to increase pressure; counterclockwise
to decrease). Close the torch or appliance valve im
mediately after resetting the regulator.
STOPPI G WORK:
Whenever you stop work, and you are going to leave
the outfit unattended, follow this procedure:
1. Close the tank (cylinder) valve.
2. Turn the pressure adjusting screw on the regulator
in and open the torch or appliance at the end of the
hose. This will bleed the gas from the system down
stream of the tank (cylinder) valve.
3. Back out the pressure adjusting screw on the regu
lator.
REPAIRI G:
Regulators in need of repair should be returned to your
Prest O Lite dealer or to an ESAB welding equipment
distributor. NEVER remove the pressure adjusting screw.
If you have your own properly equipped and staffed re
pair facility, repair parts information for this regulator is
available on request to your distributor. Request Form
15 264 which covers all regulators listed on this sheet.
SAFETY PRECAUTIO S
1. DO OT let liquefied fuel gas (LFG) escape near