ESAB EM 215ic User manual

Instruction manual
0463 408 001 GB 20170228 Valid for: serial no. EMP: 615-xxx-xxxx, EM: 627-xxx-xxxx
EMP 215ic, EM 215ic

TABLE OF CONTENTS
0463 408 001 © ESAB AB 2017
1SAFETY ......................................................................................................... 5
1.1 Meaning of symbols ................................................................................. 5
1.2 Safety precautions ................................................................................... 5
2INTRODUCTION............................................................................................ 8
2.1 Equipment ................................................................................................. 8
3TECHNICAL DATA ........................................................................................ 10
4INSTALLATION.............................................................................................. 13
4.1 Location..................................................................................................... 13
4.2 Lifting instructions ................................................................................... 13
4.3 Mains supply............................................................................................. 14
4.3.1 Recommended fuse sizes and minimum cable area.............................. 15
5OPERATION .................................................................................................. 16
5.1 Connections.............................................................................................. 17
5.2 Connection of welding and return cables .............................................. 18
5.3 Polarity change......................................................................................... 18
5.4 Inserting and replacing wire.................................................................... 18
5.5 Setting the wire feed pressure ................................................................ 20
5.6 Changing the feed/pressure rollers ........................................................ 20
5.7 Shielding gas ............................................................................................ 21
5.8 Duty cycle ................................................................................................. 22
5.9 Overheating protection ............................................................................ 23
6CONTROL PANEL......................................................................................... 24
6.1 How to navigate - EMP 215ic ................................................................... 24
6.1.1 Main menu.............................................................................................. 24
6.1.2 sMIG mode............................................................................................. 24
6.1.3 Manual MIG mode.................................................................................. 25
6.1.4 Flux cored wire mode ............................................................................. 25
6.1.5 MMA mode ............................................................................................. 25
6.1.6 LIFT-TIG mode ....................................................................................... 25
6.1.7 Settings .................................................................................................. 26
6.1.8 User manual information ........................................................................ 26
6.1.9 Icon reference guide............................................................................... 26
6.2 How to navigate - EM 215ic ..................................................................... 29
6.2.1 Symbol reference EM 215ic ................................................................... 29
7MAINTENANCE............................................................................................. 30
7.1 Routine maintenance ............................................................................... 30
7.2 Power source and wire feeder maintenance ......................................... 30
7.3 Torch and liner maintenance................................................................... 31
8TROUBLESHOOTING ................................................................................... 32
9ORDERING SPARE PARTS .......................................................................... 34
DIAGRAM ............................................................................................................. 35

TABLE OF CONTENTS
0463 408 001 © ESAB AB 2017
ORDERING NUMBERS ....................................................................................... 36
WEAR PARTS....................................................................................................... 37
ACCESSORIES .................................................................................................... 39
REPLACEMENTS PARTS.................................................................................... 40
Rights reserved to alter specifications without notice.

1 SAFETY
0463 408 001 -5- © ESAB AB 2017
1 SAFETY
1.1 Meaning of symbols
As used throughout this manual: Means Attention! Be Alert!
DANGER!
Means immediate hazards which, if not avoided, will result in immediate,
serious personal injury or loss of life.
WARNING!
Means potential hazards which could result in personal injury or loss of
life.
CAUTION!
Means hazards which could result in minor personal injury.
WARNING!
Before use, read and understand the instruction manual
and follow all labels, employer´s safety practices and Safety
Data Sheets (SDSs).
1.2 Safety precautions
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
2. The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment
when it is started up
○ no-one is unprotected when the arc is struck or work is started with the
equipment
3. The workplace must:
○ be suitable for the purpose
○ be free from drafts

1 SAFETY
0463 408 001 -6- © ESAB AB 2017
4. Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which
could become trapped or cause burns
5. General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinguishing equipment must be clearly marked and close at
hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
WARNING!
Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting.
ELECTRIC SHOCK - Can kill
• Install and ground the unit in accordance with instruction manual.
• Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing.
• Insulate yourself from work and ground.
• Ensure your working position is safe
ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health
• Welders having pacemakers should consult their physician before welding.
EMF may interfere with some pacemakers.
• Exposure to EMF may have other health effects which are unknown.
• Welders should use the following procedures to minimize exposure to
EMF:
○ Route the electrode and work cables together on the same side of
your body. Secure them with tape when possible. Do not place your
body between the torch and work cables. Never coil the torch or
work cable around your body. Keep welding power source and
cables as far away from your body as possible.
○ Connect the work cable to the workpiece as close as possible to the
area being welded.
FUMES AND GASES - Can be dangerous to health
• Keep your head out of the fumes.
• Use ventilation, extraction at the arc, or both, to take fumes and gases
away from your breathing zone and the general area.
ARC RAYS - Can injure eyes and burn skin
• Protect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing.
• Protect bystanders with suitable screens or curtains.
NOISE - Excessive noise can damage hearing
Protect your ears. Use earmuffs or other hearing protection.

1 SAFETY
0463 408 001 -7- © ESAB AB 2017
MOVING PARTS - Can cause injuries
• Keep all doors, panels and covers closed and securely in place. Have only
qualified people remove covers for maintenance and troubleshooting as
necessary. Reinstall panels or covers and close doors when service is
finished and before starting engine.
• Stop engine before installing or connecting unit.
• Keep hands, hair, loose clothing and tools away from moving parts.
FIRE HAZARD
• Sparks (spatter) can cause fire. Make sure that there are no inflammable
materials nearby.
• Do not use on closed containers.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
CAUTION!
This product is solely intended for arc welding.
WARNING!
Do not use the power source for thawing frozen pipes.
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be potential
difficulties in ensuring electromagnetic compatibility of class
A equipment in those locations, due to conducted as well
as radiated disturbances.
NOTE!
Dispose of electronic equipment at the recycling
facility!
In observance of European Directive 2012/19/EC on Waste
Electrical and Electronic Equipment and its implementation
in accordance with national law, electrical and/or electronic
equipment that has reached the end of its life must be
disposed of at a recycling facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved collection
stations.
For further information contact the nearest ESAB dealer.
ESAB has an assortment of welding accessories and personal protection equipment
for purchase. For ordering information contact your local ESAB dealer or visit us on
our website.

2 INTRODUCTION
0463 408 001 -8- © ESAB AB 2017
2 INTRODUCTION
The ESAB EM and EMP product family is a new generation of MIG and Multi-Process
(MIG/MMA/TIG) welding power sources.
The EMP 215ic and EM 215ic power sources are designed to match the needs of the
light-medium fabrication user. They are tough, durable and portable, providing excellent arc
performance across a variety of welding applications.
The EMP features a 11cm (4.3in.) colour TFT user interface display which provides quick
and easy selection of weld process and parameters, suitable for both newly trained and
intermediate level users. For more advanced users, a number of additional functions and
features can be introduced and customized to give maximum flexibility.
Exclusive to ESAB, sMIG provides users with an excellent 'Short circuit' arc characteristic.
The EM and EMP family connects to an input power supply range between
120V–230V,1~50/60Hz input power supplies. Input power can be supplied by mains or
generator. Incorporating a PFC (Power Factor Correction) circuit significantly increases
power efficiency.
Key features:
• Excellent MIG characteristics (EM)
• Excellent multi-process welding capabilities , MIG/MMA and Lift/TIG (EMP)
• Automatic recognition of input power with PFC (120V–230V)
• Large 11cm (4.3in.) high resolution, customizable user interface (EMP)
• Rugged case design and internal hardware
• Portable, single person lift and carry design
• High grade cast aluminium wire drive system provides excellent control of drive roll
geometry ensuring smooth, precise wire feeding
• Professional high grade accessories
2.1 Equipment
Package consists of the following:
EMP series
• ESAB EMP 215ic power source
• ESAB MXL 200 MIG torch, 3m (10ft)
• Contact tip M6 for 0.8mm (0.030in.) wire (qty 2)
• Contact tip M6 for 1.0mm (0.040in.) wire (qty 2)
• Gas hose, 4.5m (14.8ft), Quick connector
• MMA welding cable kit 3m (10ft)
• Return cable kit 3m (10ft)
• OK 12.50 0.8mm(0.030in.) ×5kg (11lb) bobbin
• Drive roll: 0.6 / 0.8 mm (0.023in. / 0.030in.) Cored, Steel and Stainless wire
(installed on drive system)
• Drive roll: 0.8/1.0mm (0.030in. / 0.040in.) Cored, Steel and Stainless wire (in
accessory box)
• Guide tube 1.0mm – 1.2mm (0.040in. – 0.045in.) (installed on drive system)
• Guide tube 0.6mm – 0.8mm (0.023in. – 0.030in.) (in accessory box)
• Mains cable 3m (10ft), fixed with plug
• Safety manual
• USB with Operator's Manual
• Material thickness guide

2 INTRODUCTION
0463 408 001 -9- © ESAB AB 2017
EM series
• ESAB EM 215ic power source
• ESAB MXL 200 MIG torch, 3m (10ft)
• Contact tip M6 for 0.8mm (0.030in.) wire (qty 2)
• Contact tip M6 for 1.0mm (0.040in.) wire (qty 2)
• Gas hose, 4.5m (14.8ft), Quick connector
• Return cable kit 3m (10ft)
• OK 12.50 0.8mm(0.030in.) ×5kg (11lb) bobbin
• Drive roll: 0.6 / 0.8 mm (0.023in. / 0.030in.) Cored, Steel and Stainless wire
(installed on drive system)
• Drive roll: 0.8/1.0mm (0.030in. / 0.040in.) Cored, Steel and Stainless wire (in
accessory box)
• Guide tube 1.0mm – 1.2mm (0.040in. – 0.045in.) (installed on drive system)
• Guide tube 0.6mm – 0.8mm (0.023in. – 0.030in.) (in accessory box)
• Mains cable 3m (10ft), fixed with plug
• Safety manual
• USB with Operator's Manual
• Material thickness guide

3 TECHNICAL DATA
0463 408 001 - 10 - © ESAB AB 2017
3 TECHNICAL DATA
EMP 215ic
Voltage 230 V, 1 ~ 50/60 Hz 120 V, 1 ~ 50/60 Hz
Primary current
Imax. GMAW - MIG
30 A
Breaker 20 A: 28.6 A
Breaker 15 A: 20.3 A
Imax. GTAW - TIG 19 A Breaker 15 A: 20.8 A
Imax. SMAW - MMA 25 A Breaker 15 A: 20.8 A
Ieff. GMAW - MIG
14 A
Breaker 20 A: 13 A
Breaker 15 A: 13 A
Ieff. GTAW - TIG 10 A Breaker 15 A: 14.7 A
Ieff. SMAW - MMA 13 A Breaker 15 A: 14.7 A
Permissible load at GMAW - MIG
100% duty cycle 110 A / 19.5 V Breaker 20 A: 90 A / 18.5 V
Breaker 15 A: 75 A / 17.75 V
60% duty cycle 125 A / 20.25 V Breaker 20 A: 110 A / 19.5 V
Breaker 15 A: 90 A / 18.5 V
40% duty cycle 150 A / 21.5 V Breaker 15 A: 100 A / 19 V
25% duty cycle 205 A / 24.25 V -
20% duty cycle - Breaker 20 A: 130 A / 20.5 V
Setting range (DC) 15 A / 14.75 V –
230A/25.5V
15 A / 14.75 V –
130A/20.5V
Permissible load at GTAW - TIG
100% duty cycle 110 A / 14.4 V 100 A / 14 V
60% duty cycle 125 A / 15 V 120 A / 14.8 V
40% duty cycle - 130 A / 15.2 V
30% duty cycle 180 A / 17.2 V -
Setting range (DC) 5 A / 10.2 V – 200A/18V 5 A / 10.2 V – 150A/16V
Permissible load at SMAW - MMA
100% duty cycle 100 A / 24 V 65 A / 22.6 V
60% duty cycle 125 A / 25 V 80 A / 23.2 V
40% duty cycle - 85A / 23.4V
25% duty cycle 180 A / 27.2 V -
Setting range (DC) 16 A / 20.6 V – 180A/27.2V 16 A / 20.6 V – 110A/24.4V
Open circuit voltage (OCV)
VRD deactivated, nominal
OCV (Boost OCV)
68 V / (90 V) 68 V / (90 V)
Efficiency 86% 84%
Power factor 0.98 0.99

3 TECHNICAL DATA
0463 408 001 - 11 - © ESAB AB 2017
EMP 215ic
Wire feed speed 1.5–12m/min
(62–475in./min)
1.5–12m/min
(62–475in./min)
Wire diameter
Mild steel solid wire 0.6–1.0 mm (0.023–0.040in.) 0.6–1.0 mm (0.023–0.040in.)
Stainless steel solid wire 0.8–1.0 mm (0.030–0.040in.) 0.9–1.0 mm (0.035–0.040in.)
Flux cored wire 0.8–1.1mm (0.030–0.045in.) 0.8–1.1mm (0.030–0.045in.)
Aluminium 0.8–1.2mm (0.030–3/64in.) 0.8–1.2mm (0.030–3/64in.)
Bobbin size Ø 100–200 mm (4–8in.) Ø 100–200 mm (4–8in.)
Dimensions l×w×h 548×229×406mm
(23.0×9.0×16.0in.)
548×229×406mm
(23.0×9.0×16.0in.)
Weight 18.2 kg (40 lb) 18.2 kg (40 lb)
Operating temperature -10to+40°C (-14 to +104°F) -10to+40°C (-14 to +104°F)
Enclosure class IP23S IP23S
Application classification
EM 215ic
Voltage 230V, 1~50/60Hz 120V, 1~50/60Hz
Primary current
Imax. GMAW - MIG 30A (27.6A at 25% duty
cycle)
Breaker 20A: 28.6A
Breaker 15A: 20.3A
Ieff. GMAW - MIG
14A
Breaker 15A: 14.6A
Breaker 20A: 18.0A
Permissible load at GMAW - MIG
100% duty cycle 110A / 19.5V Breaker 15A: 75A / 17.75V
Breaker 20A: 90A / 18.5V
60% duty cycle 125A / 20.25V Breaker 15A: 90A / 18.5V
Breaker 20A: 110A / 19.5V
40% duty cycle 150A / 21.5V Breaker 15A: 100A / 19V
25% duty cycle 205A / 24.25V -
20% duty cycle - Breaker 20A: 130A / 20.5V
Setting range (DC) 15A/14.75V–235A/26.0
V
15A/14.75V–130A/20.5
V
Open circuit voltage (OCV)
VRD deactivated 68V 68V
VRD activated 35V 35V
Efficiency 86% 84%
Power factor 0.98 0.99
Wire feed speed 2–12.1m/min
(80–475in./min)
2–12.1m/min
(80–475in./min)
Wire diameter
Mild steel solid wire 0.6–0.9 mm (0.023–0.035in.) 0.6–0.9 mm (0.023–0.035in.)

3 TECHNICAL DATA
0463 408 001 - 12 - © ESAB AB 2017
EM 215ic
Stainless steel solid wire 0.8–0.9 mm (0.030–0.035in.) 0.8–0.9 mm (0.030–0.035in.)
Flux cored wire 0.8–1.1mm (0.030–0.045in.) 0.8–1.1mm (0.030–0.045in.)
Aluminium 0.8–1.2mm (0.030–3/64in.) 0.8–1.2mm (0.030–3/64in.)
Bobbin size Ø 100–200 mm (4in.–8in.) Ø 100–200 mm (4in.–8in.)
Dimensions l×w×h 548×229×406mm
(23.0×9.0×16.0in.)
548×229×406mm
(23.0×9.0×16.0in.)
Weight 18.2kg (40lb) 18.2kg (40lb)
Operating temperature -10to+40°C (-14 to +104°F) -10to+40°C (-14 to +104°F)
Enclosure class IP23S IP23S
Application classification
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld at
a certain current without overheating. The duty cycle is valid for 40°C / 104°F.
For more information see section "Duty cycle" in the OPERATION chapter.
Enclosure class
The IP code indicates the enclosure class, i.e. the degree of protection against penetration
by solid objects or water.
Equipment marked IP 23S is intended for indoor and outdoor use; however, should not be
operated in precipitation.
Application class
The symbol indicates that the power source is designed for use in areas with increased
electrical hazard.

4 INSTALLATION
0463 408 001 - 13 - © ESAB AB 2017
4 INSTALLATION
The installation must be carried out by a professional.
CAUTION!
This product is intended for industrial use. In a domestic environment this product
may cause radio interference. It is the user's responsibility to take adequate
precautions.
4.1 Location
Position the power source so that its cooling air inlets and outlets are not obstructed.
A. 100 mm (4in.)
B. 100 mm (4in.)
4.2 Lifting instructions
The power source can be lifted using any of the handles.

4 INSTALLATION
0463 408 001 - 14 - © ESAB AB 2017
WARNING!
Secure the equipment - particularly if
the ground is uneven or sloping.
4.3 Mains supply
NOTE!
Mains supply requirements
This equipment complies with IEC 61000-3-12 provided that the short-circuit
power is greater than or equal to Sscmin at the interface point between the user's
supply and the public system. It is the responsibility of the installer or user of the
equipment to ensure, by consultation with the distribution network operator if
necessary, that the equipment is connected only to a supply with a short-circuit
power greater than or equal to Sscmin. Refer to the technical data in the
TECHNICAL DATA chapter.
The supply voltage should be 230VAC±10% or 120V±10%. Too low supply voltage may
cause poor welding performance. Too high welding supply voltage will cause components to
overheat and possibly fail. Contact the local electric utility for information about the type of
electrical service available, how proper connections should be made, and inspection
required.
The Welding power source must be:
• Correctly installed, if necessary, by a qualified electrician.
• Correctly earthed (electrically) in accordance with local regulations.
• Connected to the correct size power point and fuse as table below.
NOTE!
Use the welding power source in accordance with the relevant national
regulations.
CAUTION!
Disconnect input power and secure employing ‘Lock-out’ / ‘Tagging’ procedures.
Ensure input power line disconnect switch is locked (lock-out/Tagging) in the
‘Open’ position BEFORE removing input power fuses. Connection/Disconnect
should be carried out by competent persons.

4 INSTALLATION
0463 408 001 - 15 - © ESAB AB 2017
1. Rating plate with supply connection data
4.3.1 Recommended fuse sizes and minimum cable area
WARNING!
An electrical shock or fire hazard is probable if the following electrical service
guide recommendations are not followed. These recommendations are for a
dedicated branch circuit sized for the rated output and duty cycle of the welding
power source.
120 – 230 V, 1 ~ 50/60 Hz
Supply voltage 230VAC 120VAC
Input current at maximum output 30A 30A
Maximum recommended fuse* or circuit breaker rating
*Time delay fuse
30A 30A
Maximum recommended fuse or circuit breaker rating 50A 50A
Minimum recommended cord size 2.5mm2
(13AWG)
2.5mm2
(13AWG)
Maximum recommended extension cord length 15m (50ft) 15m(50ft)
Minimum recommended grounding conductor size 2.5mm2
(13AWG)
2.5mm2
(13AWG)
Supply from power generators
The power source can be supplied from different types of generators. However, some
generators may not provide sufficient power for the welding power source to operate
correctly. Generators with Automatic Voltage Regulation (AVR) or with equivalent or better
type of regulation, with rated power 8kW, are recommended.

5 OPERATION
0463 408 001 - 16 - © ESAB AB 2017
5 OPERATION
General safety regulations for handling the equipment can be found in the "SAFETY
PRECAUTIONS" chapter of this manual. Read it through before you start using the
equipment!
NOTE!
When moving the equipment use intended handle. Never pull on the cables.
WARNING!
Rotating parts can cause injury, take great care.
WARNING!
Electric shock! Do not touch the workpiece or the welding head during operation!
WARNING!
Assure that the side covers are closed during operation.
WARNING!
Tighten the bobbin locking nut in order to prevent it from sliding off the hub.
100 mm (4in.) 200 mm (8in.)


5 OPERATION
0463 408 001 - 17 - © ESAB AB 2017
5.1 Connections
Front and rear:
1. Knob for current or wire feed speed
selection (EMP)
9. Euro torch connection
2. Display (EMP) 10. Mains cable
3. Knob for voltage selection (EMP) 11. Mains supply switch ON/OFF
4. Main knob for menu navigation (EMP) 12. Gas valve inlet female
5. Torch/Remote control connection 13. Knob for voltage selection (EM)
6. Negative output [-] 14. Display - Volt/Ampere (EM)
7. Polarity changeover cable 15. Knob for plate thickness or wire feed
speed (EM)
8. Positive output [+] 16. Knob for process selection (EM)

5 OPERATION
0463 408 001 - 18 - © ESAB AB 2017
Drive system diagram
1. Bobbin hub 4. Opening side cover
2. EMC filter 5. Gas valve
3. Circuit breaker 6. Wire feed mechanism
5.2 Connection of welding and return cables
The power source has two outputs for connecting welding and return cables (see illustration
Front and rear), a negative [-] terminal (6) and a positive [+] terminal (8).
For MIG/MMA process the output to which the welding cable is connected depends on the
type of electrode, please refer to electrode packaging for information relating to the correct
electrode polarity. Connect the return cable to the remaining welding terminal on the power
source. Secure the return cable's contact clamp to the work piece and ensure that there is
good contact.
For TIG process (requires optional TIG accessories), connect the TIG torch power cable to
the negative [-] terminal (6), see front illustration. Connect gas inlet nut to a regulated
shielding gas supply. Connect the work return lead to the positive [+] terminal (8) see
illustration Front and rear.
5.3 Polarity change
The power source is delivered with the polarity changeover cable connected to the positive
terminal. Some wires, e.g. self-shielded cored wires, are recommended to be welded with
negative polarity. Negative polarity means that the polarity changeover cable is connected to
the negative terminal and the return cable to the positive terminal. Check the recommended
polarity for the welding wire you want to use.
The polarity can be changed by moving the polarity changeover cable to suit the applicable
welding process.
5.4 Inserting and replacing wire
The EMP 215ic and EM 215ic will handle bobbin sizes of 100 mm (4in.) and 200 mm (8in.).
See TECHNICAL DATA chapter for suitable wire dimensions for each wire type.

5 OPERATION
0463 408 001 - 19 - © ESAB AB 2017
WARNING!
Do not place or point the torch near the face, hand or body as this may result in
personal injury.
WARNING!
Risk of crushing or pinching when replacing the wire bobbin! Do not use safety
gloves when inserting the welding wire between the feed rollers.
NOTE!
Make sure the correct feed/pressure rollers are used. For more information see
appendix WEAR PARTS.
NOTE!
Remember to use the correct contact tip in the welding torch for the wire diameter
used. The torch is fitted with a contact tip for 0.8 mm (0.030in.) wire. If you use
another diameter you must change the contact tip and drive roll. The wire liner
fitted in the torch is recommended for welding with Fe and SS wires.
1. Open the side cover.
2. Release the pressure roller arm by pushing the tension screw toward you (1).
3. Lift the pressure roller arm up (2).
4. With the MIG welding wire feeding from the bottom of the spool pass the electrode
wire through the inlet guide (3), between the rollers, through the outlet guide and into
the MIG torch.
5. Re-secure the pressure roller arm and wire drive tension screw and adjust the
pressure if necessary.
6. With the MIG torch lead reasonably straight, feed the wire through the MIG torch by
depressing the trigger switch.
7. Close the side cover.

5 OPERATION
0463 408 001 - 20 - © ESAB AB 2017
Welding with aluminium wire
In order to weld aluminium using the standard supplied MXL 200 MIG torch, please refer to
MIG torch instruction manual for replacing standard, steel conduit liner with Teflon conduit
liner.
Please order the following accessories: 'U' groove drive roll 1.0mm / 1.2mm (0.040in. /
0.045in.) and Teflon conduit liner (PTFE liner), 3m (10ft). See WEAR PARTS chapter in
this manual and WEAR PARTS chapter in Instruction manual for the MXL 200 for ordering
number.
5.5 Setting the wire feed pressure
Piece of wood
Start by making sure that the wire moves smoothly through the wire guide. Then set the
pressure of the wire feeder's pressure rollers. It is important that the pressure is not too
high.
To check that the feed pressure is set correctly, you can feed out the wire against an
insulated object, e.g. a piece of wood.
When you hold the welding torch approximately 6mm (¼in.) from the piece of wood
(illustration A) the feed rollers should slip.
If you hold the welding torch approximately 50mm (2in.) from the piece of wood, the wire
should be fed out and bend (illustration B).
5.6 Changing the feed/pressure rollers
One dual groove feed roller is supplied as standard. Change the feed roller to match the filler
metal.
NOTE!
Be sure not to lose the key that is located on the drive motor shaft. This key must
align with drive roll slot for proper operation.