ESAB EMP 215ic User manual

Revision: AA Issue Date: December 20, 2016 Manual No.: 0463 413 001
esab.com
ESAB
EMP 215IC/EMS 215IC
MULTI PROCESS WELDER
Service
Manual
®

WE APPRECIATE YOUR BUSINESS!
Congratulations on your new ESAB product. We are proud to have you as our cus-
tomer and will strive to provide you with the best service and reliability in the industry.
This product is backed by our extensive warranty and world-wide service network. To
locate your nearest distributor or service agency, visit us on the web at www.esab.com
This Operating Manual has been designed to instruct you on the correct use and op-
eration of your ESAB product. Your satisfaction with this product and its safe opera-
tion is our ultimate concern. Therefore please take the time to read the entire manual,
especially the Safety Precautions. They will help you to avoid potential hazards that
may exist when working with this product.
YOU ARE IN GOOD COMPANY!
The Brand of Choice for Contractors and Fabricators Worldwide.
ESAB is a Global Brand of manual and automation Plasma Cutting Products.
We distinguish ourselves from our competition through market-leading, dependable
products that have stood the test of time. We pride ourselves on technical innovation,
competitive prices, excellent delivery, superior customer service and technical support,
together with excellence in sales and marketing expertise.
Above all, we are committed to developing technologically advanced products to
achieve a safer working environment within the welding industry.

!
WARNING
Read and understand this entire Manual and your employer’s safety practices before install-
ing, operating, or servicing the equipment.
While the information contained in this Manual represents the Manufacturer's best judge-
ment, the Manufacturer assumes no liability for its use.
Multi-Process Welding Power Supply
ESAB EMP215ic/EMS215ic Service Manual Number 0463 413 001
Published by:
ESAB Group Inc
2800 Airport Rd.
Denton, Texas 76207
www.esab.com
Copyright © 2016 by ESAB
All rights reserved.
Reproduction of this work, in whole or in part, without written permission of
the publisher is prohibited.
The publisher does not assume and hereby disclaims any liability to any party
for any loss or damage caused by any error or omission in this Manual, whether
such error results from negligence, accident, or any other cause.
For Printing Material Specification refer to document 47x1914
Original Publication Date: December 20, 2016
Revision Date:
i

Be sure this information reaches the operator.
You can get extra copies through your supplier.
CAUTION
These INSTRUCTIONS are for experienced operators. If you are not fully
familiar with the principles of operation and safe practices for arc welding
and cutting equipment, we urge you to read our booklet, “Precautions and
Safe Practices for Arc Welding, Cutting, and Gouging,” Form 52-529. Do
NOT permit untrained persons to install, operate, or maintain this equip-
ment. Do NOT attempt to install or operate this equipment until you have
read and fully understand these instructions. If you do not fully understand
these instructions, contact your supplier for further information. Be sure to
read the Safety Precautions before installing or operating this equipment.
USER RESPONSIBILITY
This equipment will perform in conformity with the description thereof contained in this manual and
accompanying labels and/or inserts when installed, operated, maintained and repaired in accordance
with the instructions provided. This equipment must be checked periodically. Malfunctioning or
poorly maintained equipment should not be used. Parts that are broken, missing, worn, distorted or
contaminated should be replaced immediately. Should such repair or replacement become neces-
sary, the manufacturer recommends that a telephone or written request for service advice be made
to the Authorized Distributor from whom it was purchased.
This equipment or any of its parts should not be altered without the prior written approval of the
manufacturer. The user of this equipment shall have the sole responsibility for any malfunction which
results from improper use, faulty maintenance, damage, improper repair or alteration by anyone
other than the manufacturer or a service facility designated by the manufacturer.
!
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR
OPERATING.
PROTECT YOURSELF AND OTHERS!

ESAB EMS215C/EMP215C
Manual 0463 413 001 DECLARATION OF CONFORMITY 5
EU DECLARTION OF CONFORMITY
According to
The Low Voltage Directive 2014/35/EU, entering into force 20 April 2016
The EMC Directive 2014/30/EU, entering into force 20 April 2016
The RoHS Directive 2011/65/EU, entering into force 2 January 2013
Type of equipment
Welding power source
Type designation
EMP 215ic, from serial number 615 xxx xxxx (2016 w/21)
Brand name or trade mark
ESAB
Manufacturer or his authorised representative established within the EEA
Name, Address, and telephone No:
ESAB AB
Lindholmsallén 9, Box 8004, SE-402 77 Göteborg, Sweden
Phone: [phone], Fax: [phone]
The following harmonised standard in force within the EEA has been used in the design:
EN 60974-1:2012, Arc Welding Equipment - Part 1: Welding Power Sources
EN 60974-5:2013, Arc Welding Equipment - Part 5: Wire Feeders
EN 60974-10:2014, Arc Welding Equipment - Part 10: Electromagnetic Compatibility (EMC) requirements
Additional Information:
Restrictive use, Class A equipment, intended for use in location other than residential
By signing this document, the undersigned declares as manufacturer, or the manufacturer's authorised
representative established within the EEA, that the equipment in question complies with the safety require-
ments stated above.
Date Signature Position
Gothenburg Global Director of Equipment
2016-04-20 Stephen Argo
2016

ESAB EMS215C/EMP215C
6 DECLARATION OF CONFORMITY Manual 0463 413 001
This Page Intentionally Blank

TABLE OF CONTENTS
1 SAFETY PRECAUTIONS ............................................................................. 1-1
1.01 Safety precautions .......................................................................................... 1-1
1.02 User responsibility.......................................................................................... 1-6
2 SYSTEM INSTALLATION ............................................................................ 2-1
2.01 Installation ...................................................................................................... 2-1
2.02 Lifting Instructions ......................................................................................... 2-1
2.03 Location.......................................................................................................... 2-1
2.04 Mains Supply.................................................................................................. 2-2
2.05 Technical Data................................................................................................. 2-3
2.06 Connecting the Power Source to Input Supply ............................................... 2-5
3 OPERATION ........................................................................................... 3-1
3.01 General ........................................................................................................... 3-1
3.02 Controls and Connections............................................................................... 3-4
3.03 Connection of Welding and Work leads .......................................................... 3-5
3.04 Polarity Change............................................................................................... 3-5
3.05 Inserting and Replacing Wire.......................................................................... 3-6
3.06 Setting the Wire Feed Pressure....................................................................... 3-7
3.07 Changing the Feed/Pressure Rollers ............................................................... 3-7
3.08 Shielding Gas.................................................................................................. 3-8
3.09 Volt Ampere Curves ........................................................................................ 3-8
3.10 Duty Cycle..................................................................................................... 3-10
3.11 Control Panel ................................................................................................ 3-11
4 SERVICE INSTRUCTIONS ........................................................................... 4-1
4.01 What is ESD.................................................................................................... 4-1
5 POWER SUPPLY INTRODUCTION.................................................................. 5-1
5.01. Introduction ................................................................................................... 5-1
5.02. Working Principle ........................................................................................... 5-1
5.03 Block Diagram ................................................................................................ 5-2
5.04 System Schematic for CSA Systems .............................................................. 5-4
5.05 System Schematic for CE Systems................................................................. 5-6
5.06 Component Location....................................................................................... 5-8
6 TROUBLESHOOTING ................................................................................ 6-1
6.01 Error Codes..................................................................................................... 6-1
6.02 Pre Power-up Checks...................................................................................... 6-4
6.03 LED Diagnostics ........................................................................................... 6-13
6.04 Initial Power Up Test..................................................................................... 6-13
6.05 Initial Power Up Test Problems..................................................................... 6-17
6.06 Test Procedure/troubleshooting.................................................................... 6-25
6.07 PCB Layout ................................................................................................... 6-29
7 MAINTENANCE ....................................................................................... 7-1
7.01 Routine Maintenance ...................................................................................... 7-1
7.02 Power Source and Wire Feeder Maintenance.................................................. 7-2
7.03 Torch and Liner Maintenance.......................................................................... 7-2

TABLE OF CONTENTS
8 REPLACEMENT PARTS.............................................................................. 8-1
8.01. Introduction ................................................................................................... 8-1
8.02. External Replacement Parts ............................................................................ 8-2
8.03 Internal Replacement Parts 1 CSA Systems ................................................... 8-3
8.04 Internal Replacement Parts 1 CE Systems...................................................... 8-4
8.05 Internal Replacement Parts 2.......................................................................... 8-5
8.06 Wire Feeder Replacement Parts CSA Systems................................................ 8-6
8.07 Wire Feeder Replacement Parts CE Systems .................................................. 8-7
9 DISASSEMBLY........................................................................................ 9-1
9.01 Safety Precautions for Disassembly ............................................................... 9-1
9.02 User Interface TFT Display Assembly Removal............................................... 9-1
9.03 Control PCB Removal ..................................................................................... 9-3
9.04 Power PCB Assembly Removal....................................................................... 9-4
APPENDIX 1: WORKING PRINCIPLE
(BLOCK DIAGRAM) .................................................................................. A-1
APPENDIX 2: CSA SYSTEM SCHEMATIC, 115/230V UNITS.......................................... A-2
APPENDIX 3: CE SYSTEM SCHEMATIC, 115/230V UNITS ........................................... A-4
Revision History............................................................................................ A-8

ESAB EMS215C/EMP215C
Manual 0463 413 001 SAFETY INSTRUCTIONS 1-1
1 SAFETY PRECAUTIONS
1.01 Safety precautions
MEANING OF SYMBOLS
As used throughout this manual: Means Attention! Be Alert!
DANGER!
!
DANGER
Means immediate hazards which, if not avoided, will result in immediate, serious personal
injury or loss of life.
WARNING!
!
WARNING
Means potential mechanical or non-electrical hazards which could result in personal injury
or loss of life.
WARNING
Means potential electrical hazards which could result in personal injury or loss of life.
CAUTION!
!
CAUTION
Means hazards which could result in minor personal injury.
!
WARNING
Read and understand the instruction manual before installing or operating..
!
WARNING
These Safety Precautions are for your protection. They summarize precautionary information
from the references listed in Additional Safety Information section.
Before performing any installation or operating procedures, be sure to read and follow the safety
precautions listed below as well as all other manuals, material safety data sheets, labels, etc.
Failure to observe Safety Precautions can result in injury or death.

ESAB EMS215C/EMP215C
1-2 SAFETY INSTRUCTIONS Manual 0463 413 001
PROTECT YOURSELF AND OTHERS
Some welding, cutting and gouging processes are noisy and require ear protection. The arc, like
the sun, emits ultraviolet (UV) and other radiation and can injure skin and eyes. Hot metal can
cause burns. Training in the proper use of the processes and equipment is essential to prevent
accidents. Therefore:
1. Wear a welding helmet fitted with a proper shade of filter to protect you face and eyes when welding
or watching.
2. Always wear safety glasses with side shields in any work area, even if welding helmets face shields and
goggles are also required.
3. Use a face shield fitted with the correct filter and cover plates to protect your eyes, face, neck and ears
from sparks and rays of the arc when operating or observing operations. Warn bystanders not to watch
the arc and not to expose themselves to the rays of the electric-arc or hot metal.
4. Wear flameproof gauntlet type gloves, heavy long-sleeve shirt, cu less trousers, high-topped shoes
and a welding helmet or cap for protection, to protect against arc rays and hot sparks or hot metal. A
flameproof apron may also be desirable as protection against radiated heat and sparks.
5. Hot sparks or metal can lodge in rolled up sleeves, trouser cus, or pockets. Sleeves and collars should
be kept buttoned and open pockets eliminated from the front of clothing.
6. Protect other personnel from arc rays and hot sparks with a suitable non-flammable partition or curtains.
7. Use goggles over safety glasses when chipping slag or grinding. Chipped slag may be hot and can fly
far. Bystanders should also wear goggles over safety glasses.
FIRES AND EXPLOSIONS
Heat from flames and arcs can start fires. Hot slag or sparks can also cause fires and explosions.
Therefore:
1. Protect yourself and others from flying sparks and hot metal.
2. Remove all combustible materials well away from the work area or cover the materials with a protective
non-flammable covering. Combustible materials include wood, cloth, sawdust, liquid and gas fuels,
solvents, paints and coatings paper, etc.
3. Hot sparks or hot metal can fall through cracks or crevices in floors or wall openings and cause a hid-
den smoldering fire or fires on the floor below. Make certain that such openings are protected from hot
sparks and metal.
4. Do not weld, cut or perform other hot work until the work piece has been completely cleaned so that
there are no substances on the work piece which might produce flammable or toxic vapors. Do not do
hot work on closed containers. They may explode.
5. Have fire extinguishing equipment handy for instant use, such as a garden hose, water pail, sand bucket,
or portable fire extinguisher. Be sure you are trained in its use.
6. Do not use equipment beyond its ratings. For example, overloaded welding cable can overheat and
create a fire hazard.
7. After completing operations, inspect the work area to make certain there are no hot sparks or hot metal
which could cause a later fire. Use fire watchers when necessary.

ESAB EMS215C/EMP215C
Manual 0463 413 001 SAFETY INSTRUCTIONS 1-3
ELECTRICAL SHOCK
Contact with live electrical parts and ground can cause severe injury or death. DO NOT use AC
welding current in damp areas, if movement is confined, or if there is danger of falling. Therefore:
1. Be sure the power source frame (chassis) is connected to the ground system of the input power.
2. Connect the workpiece to a good electrical ground.
3. Connect the work cable to the workpiece. A poor or missing connection can expose you or others to
a fatal shock.
4. Use well-maintained equipment. Replace worn or damaged cables.
5. Keep everything dry, including clothing, work area, cables, torch/electrode holder and power source.
6. Make sure that all parts of your body are insulated from work and from ground.
7. Do not stand directly on metal or the earth while working in tight quarters or a damp area; stand on dry
boards or an insulating platform and wear rubber-soled shoes.
8. Put on dry, hole-free gloves before turning on the power.
9. Turn o the power before removing your gloves.
10.Refer to ANSI/ASC Standard Z49.1 (listed on next page) for specific grounding recommendations. Do
not mistake the work lead for a ground cable.
ELECTRIC AND MAGNETIC FIELDS
May be dangerous. Electric current flowing through any conductor causes localized Electric and
Magnetic Fields (EMF). Welding and cutting current creates EMF around welding cables and
welding machines. Therefore:
1. Welders having pacemakers should consult their physician before welding. EMF may interfere with
some pacemakers.
2. Exposure to EMF may have other health eects which are unknown.
3. Welders should use the following procedures to minimize exposure to EMF:
a) Route the electrode and work cables together. Secure them with tape when possible.
b) Never coil the torch or work cable around your body.
c) Do not place your body between the torch and work cables. Route cables on the same side of your
body.
d) Connect the work cable to the workpiece as close as possible to the area being welded.
e) Keep welding power source and cables as far away from your body as possible.
FUMES AND GASES
Fumes and gases, can cause discomfort or harm, particularly in confined spaces. Shielding
gases can cause asphyxiation. Therfore:
1. Keep your head out of the fumes. Do not breathe the fumes and gases.
2. Always provide adequate ventilation in the work area by natural or mechanical means. Do not weld, cut
or gouge on materials such as galvanized steel, stainless steel, copper, zinc, lead beryllium or cadmium
unless positive mechanical ventilation is provided. Do not breathe fumes from these materials.
3. Do not operate near degreasing and spraying operations. The heat or arc can react with chlorinated
hydrocarbon vapors to form phosgene, a highly toxic gas and other irritant gases.

ESAB EMS215C/EMP215C
1-4 SAFETY INSTRUCTIONS Manual 0463 413 001
4. If you develop momentary eye, nose or throat irritation while operating, this is an indication that ventila-
tion is not adequate. Stop work and take necessary steps to improve ventilation in the work area. Do
not continue to operate if physical discomfort persists.
5. Refer to ANSI/ASC Standard Z49.1 (see listing below) for specific ventilation recommendations.
6. WARNING: This product when used for welding or cutting, produces fumes or gases which contain
chemicals known to the State of California to cause birth defects and in some cases cancer (California
Health & Safety Code §25249.5 et seq.)
CYLINDER HANDLING
Cylinders, if mishandled, can rupture and violently release gas. Sudden rupture of cylinder valve
or relief device can injure or kill. Therefore:
1. Locate cylinders away from heat, sparks and flames. Never strike an arc on a cylinder.
2. Use the proper gas for the process and use the proper pressure reducing regulator designed to operate
from the compressed gas cylinder. Do not use adaptors. Maintain hoses and fittings in good condition.
Follow manufacturer's operating instructions for mounting regulator to a compressed gas cylinder.
3. Always secure cylinders in an upright position by chain or strap to suitable hand trucks, undercarriages,
benches, wall, post or racks. Never secure cylinders to work tables or fixtures where they may become
part of an electrical circuit.
4. When not in use, keep cylinder valves closed. Have valve protection cap in place if regulator is not
connected. Secure and move cylinders by using suitable hand trucks.
5. For additional information, refer to CGA Standard P-1, “Precautions for Safe Handling of Compressed
Gases in Cylinders”, which is available from Compressed Gas Association, 1235 Jeerson Davis High-
way, Arlington, VA 22202.
MOVING PARTS
Moving parts, such as fans, rotors and belts can cause injury. Therefore:
1. Keep all doors, panels and covers closed and securely in place.
2. Stop engine before installing or connecting unit.
3. Have only qualified people remove covers for maintenance and troubleshooting as necessary
4. To prevent accidental starting of equipment during service, disconnect negative (-) battery cable from
battery.
5. Keep hands, hair, loose clothing and tools away from moving parts.
6. Reinstall panels or covers and close doors when service is finished and before starting engine.
!
WARNING
FALLING EQUIPMENT CAN INJURE
• Only use lifting eye to lift unit. Do NOT use running gear, gas cylinders or any other
accessories.
• Use equipment of adequate capacity to lift and support unit.
• If using lift forks to move unit, be sure forks are long enough to extend beyond op-
posite side of unit.
• Keep cables and cords away from moving vehicles when working from an aerial loca-
tion.

ESAB EMS215C/EMP215C
Manual 0463 413 001 SAFETY INSTRUCTIONS 1-5
!
WARNING
EQUIPMENT MAINTENANCE
Faulty or improperly maintained equipment can cause injury or death. Therefore:
1. Always have qualified personnel perform the installation, troubleshooting and maintenance
work. Do not perform any electrical work unless you are qualified to perform such work.
2. Before performing any maintenance work inside a power source, disconnect the power
source from the incoming electrical power.
3. Maintain cables, grounding wire, connections, power cord and power supply in safe
working order. Do not operate any equipment in faulty condition.
4. Do not abuse any equipment or accessories. Keep equipment away from heat sources
such as furnaces, wet conditions such as water puddles, oil or grease, corrosive atmo-
spheres and inclement weather.
5. Keep all safety devices and cabinet covers in position and in good repair.
6. Use equipment only for its intended purpose. Do not modify it in any manner.
!
CAUTION
ADDITIONAL SAFETY INFORMATION
For more information on safe practices for electric arc welding and cutting equipment, ask your sup-
plier for a copy of “Precautions and Safe Practices for Arc Welding, Cutting and Gouging”, Form 52-529.
The following publications are recommended to you:
1. ANSI/ASC Z49.1 - “Safety in Welding and Cutting”
2. AWS C5.5 - “Recommended Practices for Gas Tungsten Arc Welding”
3. AWS C5.6 - “Recommended Practices for Gas Metal Arc welding”
4. AWS SP - “Safe practices” - Reprint, Welding Handbook
5. ANSI/AWS F4.1 - “Recommended Safe Practices for Welding and Cutting of Containers
That Have Held Hazardous Substances”
6. OSHA 29 CFR 1910 - “Safety and health standards”
7. CSA W117.2 - “Code for safety in welding and cutting”
8. NFPA Standard 51B, “Fire Prevention During Welding, Cutting, and Other
Hot Work"
9. CGA Standard P-1, “Precautions for Safe Handling of Compressed Gases in
Cylinders”
10.ANSI Z87.1, "Occupational and Educational Personal Eye and Face
Protection Devices"

ESAB EMS215C/EMP215C
1-6 SAFETY INSTRUCTIONS Manual 0463 413 001
1.02 User responsibility
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the
equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that
apply to this type of equipment. The following recommendations should be observed in addition to the standard
regulations that apply to the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the equipment. Incor-
rect operation of the equipment may lead to hazardous situations which can result in injury to the operator and
damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
• its operation
• location of emergency stops
• its function
• relevant safety precautions
• welding and cutting or other applicable operation of the equipment
2. The operator must ensure that:
• no unauthorised person is stationed within the working area of the equipment when it is started up
• no-one is unprotected when the arc is struck or work is started with the equipment
3. The workplace must:
• be suitable for the purpose
• be free from drafts
4. Personal safety equipment:
• Always wear recommended personal safety equipment, such as safety glasses, flame-proof clothing,
safety gloves
• Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become trapped
or cause burns
5. General precautions:
• Make sure the return cable is connected securely
• Work on high voltage equipment may only be carried out by a qualified electrician
• Appropriate fire extinquishing equipment must be clearly marked and close at hand
• Lubrication and maintenance must not be carried out on the equipment during operation
!
WARNING
Arc welding and cutting can be injurious to yourself and others. Take precautions when welding and
cutting. Ask for your employer’s safety practices which should be based on manufacturers’ hazard
data.
ELECTRIC SHOCK - Can kill
• Install and earth the unit in accordance with applicable standards
• Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing
• Insulate yourself from earth and the work piece
• Ensure your working stance is safe
FUMES AND GASES - Can be dangerous to health
• Keep your head out of the fumes
• Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breath-
ing zone and the general area

ESAB EMS215C/EMP215C
Manual 0463 413 001 SAFETY INSTRUCTIONS 1-7
ARC RAYS - Can injure eyes and burn skin
• Protect your eyes and body. Use the correct welding screen and filter lens and wear
protective clothing
• Protect bystanders with suitable screens or curtains
FIRE HAZARD
• Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable
materials nearby
NOISE - Excessive noise can damage hearing
Protect your ears. Use earmus or other hearing protection.
MALFUNCTION - Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
REFERENCE TO CAN/CSA-W117.2-06
!
WARNING
Do not use the power source for thawing frozen pipes.
!
CAUTION
This product is solely intended for arc welding.
ESAB can provide you with all necessary welding protection and accessories.

ESAB EMS215C/EMP215C
1-8 SAFETY INSTRUCTIONS Manual 0463 413 001
This Page Intentionally Blank

ESAB EMS215C/EMP215C
Manual 0463 413 001 INSTALLATION 2-1
2 SYSTEM INSTALLATION
2.01 Installation
If you are not experienced seek help from a professional before installing.
!
CAUTION
This product is intended for industrial use. In a domestic environ-
ment this product may cause radio interference. It is the user's
responsibility to take adequate precautions.
2.02 Lifting Instructions
The Power Supply includes a series of handles for hand lifting only.
2.03 Location
Position the power source such that its cooling air inlets and outlets are not obstructed.
A - 4” (100 mm)
B - 4” (100 mm)
A
B
Secure the equipment - particularly if the ground is uneven or sloping.

ESAB EMS215C/EMP215C
2-2 INSTALLATION Manual 0463 413 001
2.04 Mains Supply
NOTE!
Mains suppy requirments for CE version
This equipment complies with IEC 61000-3-12 provided that the short-circuit
power is greater than or equal to Sscmin at the interface point between the
user's supply and the public system. It is the responsibility of the installer or
user of the equipment to ensure, by consultation with the distribution network
operator if necessary, that the equipment is connected only to a supply with a
short-circuit power greater than or equal to Sscmin. Refer to the technical data
in the TECHNICAL DATA chapter.
The supply voltage should be within 230VAC ± 10% or 120 V ± 10%. Too low a supply voltage may cause poor
welding performance in Stick mode such as the arc snung out during welding. Too high a supply voltage
will cause components to overheat and possibly fail. Contact the local electric utility for information about the
type of electrical service available, how proper connections should be made, and inspection required. The line
disconnect switch provides a safe and convenient means to completely remove all electrical power from the
welding power supply whenever necessary to inspect or service the unit. If no disconnect switch is available
then unplug the power cord from the wall.
The Welding power source must be:
• Correctly installed, if necessary, by a qualified electrician.
• Correctly earthed (electrically) in accordance with local regulations.
• Connected to the correct size power point and fuse as table below.
Do not connect the input (WHITE or BLACK) conductor to the ground terminal. Do not connect the ground
(GREEN) conductor to an input line terminal.
!
WARNING
The power source must be electrically connected by a qualified electrical
trades-person. Damage to the PCA (Power Control Assembly) could occur if
265 VAC or higher is applied to the primary power cable.
WARNING
ELECTRIC SHOCK can kill; SIGNIFICANT DC VOLTAGE is present after removal
of input power. DO NOT TOUCH live electrical parts..
2.4.1 Recommended Fuse Sizes and Minimum Cable Size
WARNING
An electrical shock or fire hazard is probable if the following electrical service
guide recommendations are not followed. These recommendations are for a
dedicated branch circuit sized for the rated output and duty cycle of the welding
power source.
50/60Hz single phase supply
Supply voltage 230V AC 120V AC
Input current at maximum output 30 Amps 30 Amps
Maximum recommended fuse* or circuit breaker rating
*Time delay fuse UL class RK5. Refer to UL 248
30 Amps 30 Amps
Maximum recommended fuse* or circuit breaker rating
*Normal operating UL class K5. Refer to UL 248
50 Amps 50 Amps
Minimum recommended cord size 12 AWG (4 mm2) 12 AWG (4 mm2)
Maximum recommended extension cord length 50 ft (15m) 25 ft (8m)
Minimum recommended grounding conductor size 12 AWG (4 mm2 ) 12 AWG (4 mm2)

ESAB EMS215C/EMP215C
Manual 0463 413 001 INSTALLATION 2-3
Supply from power generators
The power source can be supplied from dierent types of generators. However, some generators may not
provide sucient power for the welding power source to operate correctly. Generators with Automatic Voltage
Regulation (AVR) or with equivalent or better type of regulation, with rated power 8 kW, are recommended.
2.05 Technical Data
EMP 215ic
Voltage 230 V,1 ~ 50/60 Hz 120 V, 1 ~ 50/60 Hz
Primary current
Imax. GMAW - MIG 30 A (27.6A @ 25% duty cycle) 20 A Breaker: 28.6 A
15 A Breaker: 20.3 A
Imax. GTAW - TIG 19 A 15 A Breaker: 20.8 A
Imax. SMAW - Stick 25 A 15 A Breaker: 20.8 A
Ie. GMAW - MIG 14 A 20 A Breaker: 13 A
15 A Breaker: 14.6 A
Ie. GTAW - TIG 10 A 15 A Breaker: 14.7 A
Ie. SMAW - Stick 13 A 15 A Breaker: 14.7 A
Permissible load in GMAW - MIG
100% duty cycle 110 A / 19.5 V 15A Breaker: 75 A / 17.75 V
20A Breaker: 90 A / 18.5 V
60% duty cycle 125 A / 20.25 V 15A Breaker: 90 A / 18.5 V
20A Breaker: 110 A / 19.5 V
40% duty cycle 150A / 21.5 V 15A Breaker: 100 A / 19 V
25% duty cycle 205 A / 24.25 V
20% duty cycle 20A Breaker: 130 A / 20.5 V
Setting range (DC) 15 A / 14.75 V - 235 A / 26 V 15 A / 14.75 V - 130 A / 20.5 V
Permissible load in GTAW - TIG
100% duty cycle 110 A / 14.4 V 100 A / 14 V
60% duty cycle 125 A / 15 V 120 A / 14.8 V
40% duty cycle 130 A / 15.2 V
30% duty cycle 180 A / 17.2 V
Setting range (DC) 5 A / 10.2 V - 200 A / 18 V 5 A / 10.2 V - 200 A / 18.0 V
Permissible load in SMAW - Stick
100% duty cycle 100 A / 24 V 65 A / 22.6 V
60% duty cycle 125 A / 25 V 80 A / 23.2 V
40% duty cycle - 85 A / 23.4V
25% duty cycle 180A / 27.2 V -
Setting range (DC) 16 A / 20.6 V - 180 A / 27.2 V 16 A / 20.6 V - 130 A / 25.2 V
Open circuit voltage (OCV)
VRD Deactivated 68 V 68 V
VRD Activated 35V 35V
Eciency 86% 84%
Power factor 0.98 0.99
Wire feed speed 80-475 inch/min
(2-12.1 m/min)
80-475 inch/min
(2-12.1 m/min)
Wire diameter
Mild steel solid wire .023” (0.6 mm) - .035”
(0.9 mm)
.023” (0.6 mm) - .035”
(0.9 mm)
Stainless steel solid wire .030” (0.8 mm) - .035”
(0.9 mm)
.030” (0.8 mm) - .035”
(0.9 mm)
Flux cored wire .030” (0.8 mm) - .045”
(1.1 mm)
.030” (0.8 mm) - .045”
(1.1 mm)
Aluminium .030” (0.8 mm) - 3/64"
(1.2 mm)
.030” (0.8 mm) - 3/64"
(1.2 mm)
Wire Spool size Ø 4”- 8” (100-200 mm) Ø 4”- 8” (100-200 mm)

ESAB EMS215C/EMP215C
2-4 INSTALLATION Manual 0463 413 001
Dimensions L×W×H 23.0” (548 mm) × 9.0”
(229 mm) × 16.0” (406 mm)
23.0” (548 mm) × 9.0”
(229 mm) × 16.0” (406 mm)
Weight 40 lbs (18.2 kg) 40 lbs (18.2 kg)
Operating temperature -14 to +104 °F (-10 to +40 °C) -14 to +104 °F (-10 to +40 °C)
Enclosure class IP23S IP23S
Application classification
EMS 215ic
Voltage 230 V, 1 ~ 50/60 Hz 120 V, 1 ~ 50/60 Hz
Primary current
Imax. GMAW - MIG 30 A (27.6 A @ 25% duty cycle
20 A Breaker: 28.6 A
15 A Breaker: 20.3 A
Imax. SMAW - Stick 25 A 15 A Breaker: 20.8 A
Ie. GMAW - MIG 14A
20 A Breaker: 18 A
15 A Breaker: 14.6 A
Ie. SMAW - Stick 13 A 15 A Breaker: 14.7 A
Permissible load at GMAW - MIG
100% duty cycle 110 A / 19.5 V
20 A Breaker: 90 A / 18.5 V
15 A Breaker: 75 A / 17.75 V
60% duty cycle 125 A / 20.25 V
20 A Breaker: 110 A / 19.5 V
15 A Breaker: 90 A / 18.5 V
40% duty cycle 150 A / 21.5 V 15 A Breaker: 100 A / 19 V
25% duty cycle 205 A / 24.25 V -
20% duty cycle - 20 A Breaker: 130 A / 20.5 V
Setting range (DC) 15 A / 14.75 V - 220 A / 26 V 15 A / 14.75 V - 130 A / 21 V
Permissible load at SMAW - Stick
100% duty cycle 100 A / 24 V 65 A / 22.6 V
60% duty cycle 125 A / 25 V 80 A / 23.2 V
40% duty C 85 A / 23.4 V
25% duty cycle 180 A / 27.2 V -
Setting range (DC) 16 A / 20.6 V - 180 A / 27.2 V 16 A / 20.6 V - 130 A / 25.2 V
Open circuit voltage (OCV)
VRD Deactivated 68 V 68 V
VRD Activated 35V 35V
Eciency 86% 84%
Power factor 0.98 0.99
Wire feed speed 80-475 inch/min
(2-12.1 m/min)
80-475 inch/min
(2-12.1 m/min)
Wire diameter
Mild steel solid wire .023” (0.6 mm) - .035” (0.9 mm) .023” (0.6 mm) - .035” (0.9 mm)
Stainless steel solid wire .030” (0.8 mm) - .035” (0.9 mm) .030” (0.8 mm) - .035” (0.9 mm)
Flux cored wire .030” (0.8 mm) - .045”
(1.1 mm)
.030” (0.8 mm) - .045”
(1.1 mm)
Aluminium .030” (0.8 mm) - 3/64"
(1.2 mm)
.030” (0.8 mm) - 3/64"
(1.2 mm)
Wire Spool size Ø 4”- 8” (100-200 mm) Ø 4”- 8” (100-200 mm)
Dimensions l×w×h 23.0” (548 mm) × 9.0”
(229 mm) × 16.0” (406 mm)
l×w×h 23.0” (548 mm) × 9.0”
(229 mm) × 16.0” (406 mm)
Weight 40 lbs (18.2 kg) 40 lbs (18.2 kg)
Operating temperature -14 to +104 °F (-10 to +40 °C) -14 to +104 °F (-10 to +40 °C)
Enclosure class IP23S IP23S
Application classification