ESCALADE GOALRILLA STRIKER TRAINER TR5000 User manual

MODEL NO.
TR5000
STRIKER TRAINER
2L-7250-00
THE TOUGHEST TRAINING SYSTEM ON THE PLANET.
Escalade Sport products may be manufactured and/or licensed under the following patents.
6419596, 6179733, 5919102, 5071120, 4798381, 4424968, D326128
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2011 Escalade Sports
R
C
R
TM

MODEL NO.
TR5000
STRIKER TRAINER
2L-7250-00
THE TOUGHEST TRAINING SYSTEM ON THE PLANET.
1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before
assembling or ordering parts.
3. If hardware is tightened too soon, mounting holes may not align and parts may not easily fit together.
Leave bolts slightly loose until you are instructed to tighten them.
4. Tools required for assembly:
Allen Wrench T1 (inlcuded) Rubber Mallet
5. To make assembly as easy as possible, place all parts of the trainer in a cleared area and remove the
packaging material. Organize all parts as per parts identifier in the assembly manual. Do not dispose
of the packing material until assembly is completed.
6. Avoid scratching metal tube parts during the assembly process.
7. Assemble product on level surface.
8. Take time to correctly orientate parts exactly as per each assembly diagram.
9. Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
OWNER’S MANUAL
Please visit our website at: www.Goalrilla.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE SPORTS PRODUCT INFORMANTION
R
Escalade Sport products may be manufactured and/or licensed under the following patents.
6419596, 6179733, 5919102, 5071120, 4798381, 4424968, D326128
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2011 Escalade Sports
R
C
R
TM
Please Do Not Return This Product To The Store!
Contact Escalade Sports customer service department at:
Phone: 1-888-USA-GOAL Toll-Free!
Fax: [phone] Toll-Free!
E-mail:[email protected]
R
Mailing Address:
Escalade Sports
PO Box 889
Evansville, IN 47706
FOR ASSEMBLY VIDEOS, VISIT:
www.goalrilla.com/training

WARNING
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY AND/OR
PROPERTY DAMAGE
Owner must ensure that all users know and follow these rules for safe operation of the
product.
• Product is recommended for children 9 years of age and older.
• Strangulation hazard, keep young children away from netting.
• Do not climb or jump on any part of the product including the rebound net.
• Do not use in gusty or severe winds. It is recommended to store indoors, or chained to
a nearby sturdy structure, during windy/stormy days.
• Never use the rebounder side and goal side at the same time.
• Balls can come back off the rebound net an frame at high speeds. Be prepared for the
returning ball.
• During play, do not wear jewelry (rings, watches, necklaces, etc.) Objects may entangle
in the net.
• Check product before each use for loose hardware, frayed nets or bungee cord, or signs
of rust and instability. Repair before each use. Never play on damaged equipment.
• This goal is not to be stored or used on a slop or hill area.
• Always exercise caution when moving goals.
• Always instruct player on the safe handling and potential dangers associated with
movable goals.
• This goal should be securely anchored when possible.
• This goal is exempt from the requirements of ASTM F2673 (All goals must be anchored)
• When inserting P21 - Ground Stakes into the ground, make sure to choose an area where
there are no underground pipes or cables that could be damaged by the stakes.
- 3 -

HARDWARE IDENTIFIER (To Scale)
- 4 -
H2 - M6 x 12mm
Flat Washer
(22 pcs)
H3 - M6
Lock Washer
(22 pcs)
PARTS IDENTIFIER (Not to Scale)
P1L - Black Left Back
Bottom Corner (1 pc) P2R - Black Right Back Bottom Corner (1 pc) P3 - Black Bottom Side Connecting
Tube (2 pcs)
P4 - Orange Front
Bottom Corner (2 pcs) P5 - Orange Front Vertical Connection
Tube (2 pcs)
P6 - Black Back
Vertical Connection
Tube (2 pcs)
P7L - Black Left Back
Top Corner (1 pc) P8R - Black Right Back Top Corner (1 pc) P9L - Black Left Top Side Connecting
Tube (1 pc)
H1 - M6 x 16mm
Allen Head Bolt
(22 pcs)
T1 - M6 Allen
Wrench - 4mm
(1 pc)
(Not to Scale)
Goalrilla logo
in this side

PARTS IDENTIFIER (Not to Scale)
P10R - Black Right
Top Side Connecting
Tube (1 pc)
P11L - Orange Left
Front Top Corner (1 pc) P12R - Orange Right
Front Top Corner (1 pc)
- 5 -
P13 - Black Back Bottom Top Horizontal
Connecting Tube (2 pcs) P14 - Orange Front Top Horizontal
Connecting Tube (1 pc)
P15 - Rebound / Goal
Net (1 pc) P16L - Left Side
Net (1 pc) P17R - Right Side
Net (1 pc)
P18 - 256” Rebound /
Goal Net Outer
Perimeter
Bungee Cord
(1 pc)
P19 - 70-7/8”
Secondary Rebound /
Goal Net Top-Back
Bungee Cord
(1 pc use / 1 Extra pc
for Future Use)
P20 - 185” Side
Net Bungee
Cord (2 pcs)
P21 - Ground
Stake (4 pcs)

STEP 1:
DO NOT TIGHTEN ANY ALLEN HEAD BOLTS H1 UNTIL
COMPLETION OF FRAME ASSEMBLY IN STEP 4.
NOTE CORRECT ORIENTATION OF ALL PARTS AS
SHOWN IN FIGURE 1 FOR CORRECT ASSEMBLY.
Assemble P1L, P3 and P4 as shown in FIGURE 1.
Assemble P2R, P3 and P4 as shown in FIGURE 1.
Install, but do not tighten Allen Head Bolts H1 as shown
in FIGURE 1.
4 pcs - H1 Allen Head Bolt
4 pcs - H2 Flat Washer
4 pcs - H3 Lock Washer
1 pc - P1L Black Left Back Bottom Corner
1 pc - P2R Black Right Back Bottom Corner
2 pcs - P3 Black Bottom Side Connecting Tube
2 pcs - P4 Orange Front Bottom Corner
1 pc - T1 Allen Wrench
1 pc - Rubber Mallet
PARTS REQUIRED:
FIGURE 1
- 6 -
P4 P4
P3
P1L
P4
P2R
NOTE:
Shortest tube
in this location. NOTE:
Shortest tube
in this location.
H1
STEP 2:
DO NOT TIGHTEN ANY ALLEN HEAD BOLTS H1 UNTIL COMPLETION OF FRAME ASSEMBLY IN STEP 4.
NOTE CORRECT ORIENTATION OF ALL PARTS AS SHOWN IN FIGURE 1 FOR CORRECT ASSEMBLY.
Assemble P5 Tubes onto each P4 Tube as shown in FIGURE 2. Assemble P6 Tubes onto P1L and P2R Tube
as shown in FIGURE 2. Install, but do not tighten Allen Head Bolts H1 as shown in FIGURE 2.
FIGURE 2
H1
P4
P5
P6 P5
P6
P1L
P4
P2R
4 pcs - H1 Allen Head Bolt
4 pcs - H2 Flat Washer
4 pcs - H3 Lock Washer
2 pcs - P5 Orange Front Vertical
Connecting Tube
2 pcs - P6 Black Back Vertical
Connecting Tube
1 pc - T1 Allen Wrench
1 pc - Rubber Mallet
PARTS REQUIRED:
NOTE:
“D” Rings must
face back.
NOTE:
“D” Rings must
face front and
inside.
NOTE:
“D” Rings must
face back.
H3
H2
H1
H3
H2
H1
H3
H2
H1
H3
H2
H3H2
H3
H2
H1
H3 H2
H1
H3
H2

STEP 3:
DO NOT TIGHTEN ANY ALLEN HEAD BOLTS H1 UNTIL
COMPLETION OF FRAME ASSEMBLY IN STEP 4.
NOTE CORRECT ORIENTATION OF ALL PARTS AS
SHOWN IN FIGURE 3 FOR CORRECT ASSEMBLY.
Assemble P7L, P9L and P11L as shown in FIGURE 3. Attach this assembly onto P5 and P6 as shown in
FIGURE 1.
Assemble P8R, P10R and P12R as shown in FIGURE 3. Attach this assembly onto P5 and P6 as shown in
FIGURE 1.
Install, but do not tighten Allen Head Bolts H1 as shown in FIGURE 3.
8 pcs - H1 Allen Head Bolt
8 pcs - H2 Flat Washer
8 pcs - H3 Lock Washer
1 pc - P7L Black Left Back Top Corner
1 pc - P8R Black Right Back Top Corner
1 pc - P9L Black Left Top Side Connecting Tube
1 pc - P10R Black Right Top Side Connecting Tube
1 pc - P11L Orange Left Front Top Corner
1 pc - P12R Orange Right Front Top Corner
1 pc - T1 Allen Wrench
1 pc - Rubber Mallet
PARTS REQUIRED:
- 7 -
FIGURE 3
THIS STEP REQUIRES TWO OR MORE ADULTS
TO KEEP THE PARTIAL ASSEMBLIES FROM
TIPPING OVER.
CAUTION:
P7L
P11L
P9L
NOTE:
Goalrilla logo
face outside.
P5
P6
NOTE:
Shortest
tube in
this location.
NOTE:
Shortest tube
in this location.
P5
P6
NOTE:
Shortest tube
in this location.
P12R
P8R
P10R
NOTE:
Goalrilla logo
face outside.
H1
H2
H3
H1
H2
H3
H1
H2 H3
H1
H2
H3
H1
H2 H3
H1
H2
H3

- 8 -
STEP 4:
DO NOT TIGHTEN ANY ALLEN HEAD
BOLTS H1 UNTIL COMPLETION OF
FRAME ASSEMBLY IN STEP 4.
NOTE CORRECT ORIENTATION OF ALL
PARTS AS SHOWN IN FIGURE 4 FOR
CORRECT ASSEMBLY.
Assemble one piece P13 to P7L and
another one piece P13 to P1L as shown
in FIGURE 4.
Attach P14 to P11L as shown in FIGURE 4.
Next, carefully attach P13 to P8R, P14 to
P12R and P13 to P2R as shown in
FIGURE 4.
Next, on a level surface go through entire frame
assembly and tighten all twenty two pieces Allen
Head Bolts H1.
6 pcs - H1 Allen Head Bolt
6 pcs - H2 Flat Washer
6 pcs - H3 Lock Washer
2 pcs - P13 Black Back Bottom and Top Horizontal Connecting Tube
1 pc - P14 Orange Front Top Horizontal Connecting Tube
1 pc - T1 Allen Wrench
1 pc - Rubber Mallet
PARTS REQUIRED:
THIS STEP REQUIRES TWO OR MORE ADULTS
TO KEEP THE PARTIAL ASSEMBLIES FROM
TIPPING OVER.
CAUTION:
P14
P13
P13
P12R
P8R
P7L
P11L
P1L P2R
H1
H1
H3
H2
H1
H3
H2
H1
H3
H2
H3
H2
H1
H3
H2
H1
H3
H2
FIGURE 4

- 9 -
STEP 5:
With the help of another adult, attach P15 Net using P18 Bungee
Cord onto outer perimeter of the frame as shown in FIGURE 5.
IMPORTANT NOTES: Orientate net - 26 squares horizontally
by 23 squares vertically. Orientate secondary horizontal border
in the net towards the top of the net. Do not attach P15 Net to
top tubes P7L, P13 or P8R. Do not place P15 Net over top
tubes P7L, P13 or P8R.
1. Tie off one end of P18 Bungee Cord using a double knot to
the welded D-Ring on part P10R as shown in DETAIL A
and FIGURE 5.
2. With help of another adult, thread P18 Bungee Cord through
P15 Net and frame welded D-Rings, following FIGURE 5 arrows.
IMPORTANT NOTES:
A. P18 Bungee Cord should be pulled tight.
B. The welded D-Rings are 6” apart, and the net is a 3” mesh.
Thus, the general rule is to thread the bungee cord through
every other hole of the net.
C. On each corner D-Ring, pull bungee cord tight and tie a
single knot for ease of assembly.
3. Upon completion of 4th side bungee cord / net attachment, tie off
a double knot on the same D-Ring of the first/beginning bungee
cord double knot.
4. Bungee Cord should be tight on all four sides.
1 pc - P15 Rebound / Goal Net
1 pc - P18 256” Rebound / Goal Net Outer Perimeter Bungee Cord
PARTS REQUIRED:
THIS STEP REQUIRES TWO OR MORE ADULTS.
CAUTION:
Double Knot
Single
Knot
Start / finish in here
with double knot
Single
Knot
Single
Knot
P15
P18
DETAIL A
P10R
P8R
P7L
P13
FIGURE 5
IMPORTANT NOTES:
1. Orientate net - 26 Squares horizontly + 23 Squares vertically.
2. Secondary Border in net must be located towards top of net.
Secondary Border in Net
26 SQUARES
23 SQUARES

- 10 -
STEP 6:
With the help of another adult, attach P19 Bungee
Cord through the top back welded D-Rings on tubes
P17, P13, P8R and Net P15 as shown in FIGURE 6.
IMPORTANT NOTES: The P15 Rebound/Goal Net
must be orientated correctly in the previous assembly
STEP 5, in order to achieve correct assembly in this
step. The P19 Bungee Cord used in this step must be
threaded under the “thicker” horizontal secondary
border located in the top half of the P15 Rebound
Goal Net.
1. Tie off one end of P19 Bungee Cord using a
double knot on the welded D-Ring located at
the very corner of P7L Tube as shown in
FIGURE 6.
2. Carefully thread P19 Bungee Cord thorugh
every other hole in net and every welded
D-Ring on P7L, P13 and P8R Tubes as shown
in FIGURE 6.
3. When complete, pull P19 Bungee Cord tight and
tie a double knot in the corner welded D-Ring of P8R
Tube.
IMPORTANT NOTES: This assembly step will create
a distinct “top” and “back” surface of the net.
This product comes with an extra P19 Bungee Cord
for future use.
1 pc - P19 70-7/8” Secondary Rebound / Goal
Net Top-Back Bungee Cord
PARTS REQUIRED:
THIS STEP REQUIRES TWO OR MORE ADULTS.
CAUTION:
FIGURE 6
P19
1
2
3
P7L
P8R
P13

- 11 -
STEP 7:
Attach P16L & P17R Side Nets using P20 Bungee
Cords onto each side of frame assembly as shown
in FIGURE 7.
IMPORTANT NOTES: Each of the (4) corners will
require double P20 Bungee Cord threading for correct
assembly. Please follow directions and diagrams
closely. Bungee Cord should be pulled only taught
throughout these following assembly steps.
1. Tie off the end of each P20 Bungee Cord using a
double knot onto welded D-Ring on P9L and P10R
Tubes (Left or Right Side Net Attachment) as shown
in DETAIL B and FIGURE 7.
2. Thread bungee cord from the outside through corner
of top side net grommet and continue through the
corner D-Ring. Then continue back through the same
corner net grommet once again from the outside to
make a loop. Continue on to the first welded D-Ring
as shown in DETAIL B and FIGURE 7.
3. Continue threading bungee cord around all (4) sides
of frame, threading Bungee Cord through all welded
D-Rings and side net grommets as shown in FIGURE 7.
IMPORTANT NOTE: Please follow STEP 2 above
for correct “corner / net attachment”.
4. Upon completion of 4th side bungee cord / net
attachment, tie off a double knot on the same D-Ring
of first/beginning bungee cord double knot.
5. Bungee Cord should be only taught and side net
should not be loose in any areas.
STEP 8:
Upon final placement of the Striker Trainer, install (4) pcs P21 Ground Stakes onto the bottom and most outward (4) corner tubes and tap into the ground using a rubber mallet.
1 pc - P16L Left Side Net 4 pcs - P21 Ground
1 pc - P17R Right Side Net Stake
2 pcs - P20 Side Net Bungee Cord
PARTS REQUIRED:
FIGURE 7
NOTE:
Warning
label on
this side.
(inside)
NOTE:
“G” and “Goalrilla”
logo on this side.
(outside)
Double Knot
P17R
P16L
P20
P9L
P10R
Corner Net
Grommet
DETAIL B
Corner
D-Ring

- 12 -
Let us know how you Train with
The Striker Trainer.
Post a video on Goalrilla’s Youtube channel at:
youtube.com/user/TheOfficialGoalrilla
and/or Goalrilla's Facebook page at:
facebook.com/Goalrilla
GOAL SIDE
GOAL SIDE
REBOUND SIDE
REBOUND SIDE
LAYING DOWN ON GOAL SIDE
LAYING DOWN ON GOAL SIDE

- 13 -
PRODUCT PARTS LIST
PARTS# KEY# DESCRIPTION QTY.
H1 M6 x 16mm Allen Head Bolt 22
H2 M6 x 12mm Flat Washer 22
H3 M6 Lock Washer 22
T1 Allen Wrench 1
P1L Black Left Back Bottom Corner 1
P2R Black Right Back Bottom Corner 1
P3 Black Bottom Side Connecting 2
P4 Orange Front Bottom Corner 2
P5 Orange Front Vertical Connection Tube 2
P6 Black Back Vertical Connection Tube 2
P7L Black Left Back Top Corner 1
P8R Black Right Back Top Corner 1
P9L Black Left Top Side Connecting Tube 1
P10R Black Right Top Side Connecting Tube 1
P11L Orange Left Front Top Corner 1
P12R Orange Right Front Top Corner 1
P13 Black Back Bottom Top Horizontal
Connecting Tube 2
P14 Orange Back Bottom Top Horizontal
Connecting Tube 1
P15 Rebound / Goal Net 1
P16L Left Side Net 1
P17R Right Side Net 1
P18 256” Rebound / Goal Net Outer
Perimeter Bungee Cord 1
P19 70-7/8” Secondary Rebound /
Goal Net Top-Back Bungee Cord
(1 pc use / 1 Extra pc for future use) 2
P20 185” Side Net Bungee Cord 2
P21 Ground Stake 4
K1 Hardware Kit 1
M1 Owner’s Manual 1
TR5000W / F
TR5000-H1
TR5000-H2
TR5000-H3
TR5000-T1
TR5000-P1L
TR5000-P2R
TR5000-P3
TR5000-P4
TR5000-P5
TR5000-P6
TR5000-P7L
TR5000-P8R
TR5000-P9L
TR5000-P10R
TR5000-P11L
TR5000-P12R
TR5000-P13
TR5000-P14
TR5000-P15
TR5000-P16L
TR5000-P17R
TR5000-P18
TR5000-P19
TR5000-P20
TR5000-P21
TR5000-K1
TR5000-M1
To purchase these parts, please contact Escalade Sports Customer Service

1(ONE) YEAR LIMITED WARRANTY
This consumer warranty extends to the original consumer purchase of any Escalade® Sports Product (hereinafter
referred to as the “Product”).
WARRANTY COVERAGE: Escalade® Sports warrants to the original Consumer Purchaser that any Product of its
manufacture is free from defects in material and workmanship. THIS WARRANTY IS VOID IF THE PRODUCT HAS
BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO
FOLLOW INSTRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF
DEFECTS IN MATERIAL OR WORKMANSHIP.
Subject to proper installation and normal use, Escalade ® Sports warrants, subject to the limitations below, to the
original retail purchaser all structural components of the Striker Trainer™ to be free of defects in material and
workmanship for the duration of ownership by the original retail purchaser.
Merchandise must be shipped prepaid with a copy of proof of purchase to Escalade® Sports factory for examination to
determine if the trainer needs to be repaired or replaced. Any labor costs, travel expenses and any other changes
involved in the removal, installation or replacement of the defective/repaired parts from/to your Striker Trainer™ will be
the purchaser’s responsibility. Shipping charges for replaced or warranted merchandise sent back to the customer from
Escalade® Sports factory must be prepaid by the customer in advance. If not, the replacement shipment will be sent
out collect.
Escalade® Sports reserves the right to examine photographs or physical evidence of merchandise claimed to be
defective, and to recover said merchandise, prior to authorization of warranty claims. A “Returned Goods Authorization”
number may be required, please call for details (see information below) prior to the return of any photographs or
merchandise.
This 1(one) year limited warranty is expressly in lieu of all warranties, expressed or implied, including warranties of
merchantability or fitness for use. Escalade® Sports does not assume or authorize any person or representative to
assume for us, any other liability in connection with the sale of our products.
The remedy of repair or replacement stated above is Escalade® Sports exclusive remedy. Escalade® Sports will not
be liable for any other damages or expenses which may incur, including but not limited to incidental or consequential
damages. Escalade® Sports assumes no other obligations or liability on the part of the purchaser, and Escalade®
Sports neither assumes nor authorizes any other person to assume for it any other liability in connection with the goods
sold.
This warranty shall not apply in any manner to parts or accessories not manufactured by Escalade® Sports.
NOT COVERED BY THIS 1(ONE) YEAR LIMITED WARRANTY
• Bungee cords, rebound net and side nets are warranted for a period of 60 days from the original purchase
under normal use and proper care.
• Any merchandise subjected to abuse, negligence, improper installation, vandalism, acts of God, alteration of
product, or any other events beyond the control of Escalade® Sports.
• Paint or rusted parts. If rust should appear, remove loose paint, sand lightly, primer and paint anything black
with black exterior flat matte finish enamel paint, and anything orange with orange exterior gloss enamel paint.
• Shipping charges both ways. Note: Any merchandise shipped to Escalade® Sports collect will be refused.
• Dealer service charges, labor charges and travel expenses associated with replacement of repair of warranty
item.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION. ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE
PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS. EXPENSES OR DAMAGES INCURRED BY
THE CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so
the above limitations or exclusions may not apply to you. LEGAL REMEDIES: This warranty gives you specific legal
rights, and you may also have other rights which may vary from state to state.
WARRANTY GUIDELINES IS REQUIRED FOR ALL WARRANTY CLAIMS
1. Proof of Purchase (original retail purchaser) is required for all warranty claims.
2. Call or write Escalade® Sports to receive a Return Authorization # and determine specific needs. Phone: 1-888-
USA-GOAL / Warranty Dept. or Write Escalade® Sports at: Escalade® Sports -P.O. Box 889, Evansville, IN 47706
-Attn: Warranty Dept. or E-mail us at: [email protected]