ESCO Technologies ETS-Lindgren 3163-03 User manual

Model 3163 Series
High Gain
Conical Horn Antenna
User Manual

ii |
ETS-Lindgren L.P. reserves the right to make changes to any product described
herein in order to improve function, design, or for any other reason. Nothing
contained herein shall constitute ETS-Lindgren L.P. assuming any liability
whatsoever arising out of the application or use of any product or circuit
described herein. ETS-Lindgren L.P. does not convey any license under its
patent rights or the rights of others.
© Copyright 2010 by ETS-Lindgren L.P. All Rights Reserved. No part of this
document may be copied by any means without written permission from
ETS-Lindgren L.P.
Trademarks used in this document: The ETS-Lindgren logo is a trademark of
ETS-Lindgren L.P.
Revision Record
MANUAL,3163 SERIES HIGH GAIN CONICL HORN | Part # 399315, Rev. A
Revision Description Date
A Initial Release February, 2010

| iii
Table of Contents
Notes, Cautions, and Warnings................................................v
1.0 Introduction..........................................................................7
Model 3163-03...............................................................................................7
Model 3163-04...............................................................................................7
Model 3163-05...............................................................................................7
Model 3163-06...............................................................................................7
Tripod Options ...............................................................................................8
ETS-Lindgren Product Information Bulletin ...................................................9
2.0 Maintenance.......................................................................11
Annual Calibration .......................................................................................11
Service Procedures .....................................................................................11
3.0 Specifications.....................................................................13
Electrical Specifications ...............................................................................13
Physical Specifications ................................................................................13
4.0 Mounting Instructions.......................................................15
Backplate Diagrams for Custom Mounts .....................................................15
Model 3163-03.....................................................................................16
Model 3163-04.....................................................................................17
Model 3163-05.....................................................................................18
Model 3163-06.....................................................................................19
4-TR Mounting Options................................................................................20
7-TR and Mast Mounting Options................................................................20
2x2 Boom Mounting Options .......................................................................21
5.0 Typical Data........................................................................23
Appendix A: Warranty.............................................................25

iv |
This page intentionally left blank.

| v
Notes, Cautions, and Warnings
Note: Denotes helpful information intended to
provide tips for better use of the product.
Caution: Denotes a hazard. Failure to follow
instructions could result in minor personal injury
and/or property damage. Included text gives proper
procedures.
Warning: Denotes a hazard. Failure to follow
instructions could result in SEVERE personal injury
and/or property damage. Included text gives proper
procedures.
See the ETS-Lindgren Product Information Bulletin for safety,
regulatory, and other product marking information.

vi |
This page intentionally left blank.

Introduction | 7
1.0 Introduction
The ETS-Lindgren Model 3163 Series High Gain Conical Horns include these
antennas:
Model 3163-03
•C Band
•4 GHz to 8 GHz
Model 3163-04
•X Band
•8 GHz to 12 GHz
Model 3163-05
•Ku Band
•12 GHz to 18 GHz
Model 3163-06
•K Band
•18 GHz to 26.5 GHz
The Model 3163 Series was designed for use as feeds in tapered anechoic
chambers, as well as in applications requiring high gain and linear polarization.
When back mounted and attached to a rotator at the feed of the taper chamber,
the design allows for rotation inside the conical feed sections. Flared angles
enable easy positioning along the feed section to obtain the best possible
illumination of the Quiet Zone (QZ). The Model 3163 Series exhibits improved
reflectivity levels in the QZ of tapered chambers with low VSWR across the
range.

8 | Introduction
The Model 3163 Series exhibits high gain performance, with the 3163-03 C band
horn having a gain of 16 dBi or higher across the range. The X band to K band
horns exhibit gain increasing from 16.5 dBi to 25 dBi.
The VSWR of the Model 3163 Series is low, with an average level of less than
1.5:1 for most of the range. The VSWR may be higher at the edges of the band
but never exceeds 3.2:1.
The Model 3163 Series can be mounted directly into the feed section of a
tapered chamber or mounted to a tripod and used in a rectangular chamber. The
Model 3163 Series includes a built-in 1/4–20 thread mount, as well as a coaxial
to waveguide adapter. For all mounting options available for the
Model 3163 Series, see Mounting Instructions on page 15.
Tripod Options
ETS-Lindgren offers the following non-metallic, non-reflective tripods for use at
both indoor and outdoor EMC test sites.
•4-TR Tripod—Constructed of linen
phenolic and delrin, designed with an
adjustable center post for precise height
adjustments. Maximum height is 2.0 m
(80.0 in), and minimum height is 94 cm
(37.0 in). This tripod can support up to
an 11.8 kg (26.0 lb) load.

Introduction | 9
•7-TR Tripod—Constructed of PVC and
fiberglass components, providing
increased stability for physically large
antennas. The unique design allows for
quick assembly, disassembly, and
convenient storage. Allows several
different configurations, including options
for manual or pneumatic polarization.
Quick height adjustment and locking
wheels provide ease of use during
testing. Maximum height is 2.17 m
(85.8 in), with a minimum height of 0.8 m
(31.8 in). This tripod can support a
13.5 kg (30 lb) load.
ETS-Lindgren Product Information Bulletin
See the ETS-Lindgren Product Information Bulletin included with your shipment
for the following:
•Warranty information
•Safety, regulatory, and other product marking information
•Steps to receive your shipment
•Steps to return a component for service
•ETS-Lindgren calibration service
•ETS-Lindgren contact information

10 | Introduction
This page intentionally left blank.

Maintenance | 11
2.0 Maintenance
Before performing any maintenance,
follow the safety information in the
ETS-Lindgren Product Information
Bulletin included with your shipment.
Maintenance of the Model 3163 Series is
limited to external components such as
cables or connectors.
If you have any questions concerning
maintenance, contact ETS-Lindgren
Customer Service.
Annual Calibration
See the Product Information Bulletin included with your shipment for information
on ETS-Lindgren calibration services.
Service Procedures
For the steps to return a system or system component to ETS-Lindgren for
service, see the Product Information Bulletin included with your shipment.
WARRAN TY

12 | Maintenance
This page intentionally left blank.

Specifications | 13
3.0 Specifications
Electrical Specifications
3163-03 3163-04 3163-05 3163-06
Frequency
Range:
4 GHz to
8 GHz
8 GHz to
12 GHz
12 GHz to
18 GHz
18 GHz to
26.5 GHz
VSWR Ratio
(Avg):
3.2:1 Max
1.5:1 Avg
2.5:1 Max
1.5:1 Avg
2:1 Max
1.25:1 Avg
2:1 Max
1.25:1 Avg
Maximum
Continuous
Power:
250 Watts 250 Watts 200 Watts 50 Watts
Impedance
(Nominal): 50 Ω50 Ω50 Ω50 Ω
Connectors: Type N (F) Type N (F) Type N (F) SMA (F)
Physical Specifications
3163-03 3163-04 3163-05 3163-06
Length
(Without
Mount):
60.0 cm
23.5 in
37.0 cm
14.6 in
39.0 cm
15.3 in
38.0 cm
14.8 in
Aperture
Diameter:
17.8 cm
7.0 in
10.2 cm
4.0 in
10.2 cm
4.0 in
10.2 cm
4.0 in
Weight: 1.8 kg
4.0 lb
0.5 kg
1.2 lb
0.6 kg
1.4 lb
0.5 kg
1.2 lb

14 | Specifications
This page intentionally left blank.

Mounting Instructions | 15
4.0 Mounting Instructions
Before connecting any components, follow the
safety information in the ETS-Lindgren
Product Information Bulletin included with your
shipment.
The Model 3163 Series antennas are precision
measurement devices. Handle your antenna
with care.
Backplate Diagrams for Custom Mounts
The backplate on each Model 3163 Series High Gain Conical Horn provides
threaded holes for mounting directly into the feed section of a tapered chamber.
Additionally, you can use the threaded holes to create your own custom
mounting solution. Following is the backplate diagram for each
Model 3163 Series horn.

16 | Mounting Instructions
MODEL 3163-03

Mounting Instructions | 17
MODEL 3163-04

18 | Mounting Instructions
MODEL 3163-05

Mounting Instructions | 19
MODEL 3163-06

20 | Mounting Instructions
4-TR Mounting Options
The Model 3163 Series High Gain Conical Horns include a built-in 1/4–20 thread
mount for connecting directly to an ETS-Lindgren 4-TR Tripod. No additional
hardware is required.
7-TR and Mast Mounting Options
In addition to the 1/4–20 thread
mount attached to the
Model 3163 Series, here is an
additional option for mounting onto
an ETS-Lindgren 7-TR Tripod or
mast. Contact the ETS-Lindgren
Sales Department for information
on ordering optional mounting
hardware.