Essential Medical Supply B3011 User manual

G H I J
B3011 Shower Bench with Backrest
Feb 2019, Essential Medical Supply, Inc.
x 5 x 4 x 9
WARNING:
• Before using, be sure that all gold locking buttons fully protrude thru holes of each
Adjustable Leg (G).
• Make sure all Adjustable Legs are snapped in the same hole position (G).
• Periodically retighten all wing knob screws on the bottom of the seat.
ATTENTION:
USER WEIGHT LIMIT: 300lbs.
• Pleaseverifythatallcomponentsareincludedasshownabove,
beforeproceedingwithassembly.
• DONOTUSEASAVANITYSTOOL
C
DE F
Included in box:
x 4
x 2
Adjustable Leg
ArmrestBackrest Panel
x 2
Backrest Support Tubing
Short Wing
Knob Screws Long Wing Knob Screws Wave Washers
Seat PanelFrame Tubing (A) Frame Tubing (B)
A B
California Proposition 65
WARNING: Cancer & Reproductive Harm
www.P65Warnings.ca.gov

2Identify the difference between the upper and lower
Frame Tubing pieces (A & B). Both of the pieces have
stickers to identify them. One Frame Tubing piece is
labeled “A” and the other is labeled “B”.
1Place the Seat Panel (C) upside down on a at
surface with the triangle indent facing upwards. This
triangle indicates the front of the Seat Panel (C).
4Place lower Frame Tubing piece “B” in the indent
labeled “B” with the legs facing upwards crossing
over upper Frame Tubing piece “A”.
3Place upper Frame Tubing piece “A” in the indent
labeled “A”, with the legs facing upwards.
5Take one of the Short Wing Knob Screws (H) and
Wave Washers (J) and place the Wave Washer (J),
with arc facing down, onto the Wing Knob Screw (H).
Screw the Short Wing Knob Screw (H) into the hole
where the two Frame Tubing pieces (A & B) overlap.
Hand tighten the Wing Knob Screw (H) while making
sure the Wave Washer (J) aligns with the tubing.
6Identify the two different sides of the Backrest
Support Tubing (F). One side will have holes that
are farther apart while the other has holes that are
closer together.
A
B
Place the side, with the holes separated farther,
over the preexisting holes of the upper Frame
Tubing (A & B). Make sure the “L” portion of the
Backrest Support Tubing (F) is facing the back of
the Seat Panel (C) and downwards during assembly.
x 1
Upper Frame
Lower Frame
A
B
A
A
B
A
B
A
B
A
B
A
B
Holes closer together
(for Backrest (D))
Holes farther apart
(for Seat(C))

10 Identify the top of the
Backrest Panel (D). The top
portion has a handle molded
into it. Take remaining Short
Wing Knob Screws (H) and
Wave Washers (J) and place Wave
Washers (J) on the Short Wing Knob
Screws (H) as in Step 5. Line up the
holes of the Backrest Panel (D) to the
holes on the Backrest Support Tubing
(F) with top of Backrest Panel (D) up.
Take the Short Wing Knob Screws (H)
and Wave Washers (J) and fasten into
the hole. Hand tighten.
12 Now that the chair is
completely assembled,
ensure all of the Wing Knob
Screws (H & I) are tightened.
9Flip chair over and verify all Adjustable Legs (G)
are touching the oor. Make sure the chair is level
and stable.
8Identify the brass buttons on the four posts of the
Frame Tubing (A & B). Take one of the Adjustable
Legs (G) and while pressing in the button, slide the
Adjustable Leg (G) over the post until the brass
button protrudes. Adjust height accordingly and
repeat with remaining Adjustable Legs (G).
11 Take the Armrests (E) and identify the brass buttons.
Press the brass buttons in while sliding the Armrest
(E) into the frame silencers. Make sure the buttons
protrude from the holes in the Frame Tubing (A & B).
Repeat with second Armrest (E).
7Take two Long Wing Knob Screws (I) and two
Wave Washers (J) and place the Wave Washers
(J) on the Wing Knob Screws as in Step 5. Screw
the Long Wing Knob Screws (I) into the holes
where the Back Support Tubing (F) overlaps with
the Frame Tubing pieces (A & B). Hand tighten
both Wing Knob Screws. Repeat this with the
remaining Back Support Tubing (F), Long Wing
Knob Screws (I) and Wave Washers (J).
x 4 x 4
x 4
x 2
WARNING:
• Before using, be sure that
all gold locking buttons fully
protrude thru holes of each
Adjustable Leg (G).
• Make sure all Adjustable
Legs (G) are snapped in the
same hole position.
• Periodically retighten all
wing knob screws on the
bottom of the seat.
A
B
A
B