ETEKCITY ETU-134 User manual

QUICK START GUIDE
TENS Unit ETU-134
A
F
C
D
IJKLM
E N
O
H
G
B
A. Display
B. A Channel Intensity
Increase/Decrease
C. Therapy Modes [15]
D. Time Button
E. Lead Wires
F. Battery Indicator
G. B Channel Intensity
Increase/Decrease
H. Power/Pause Button
I. A1 Output
J. A2 Output
K. Micro USB Port
L. B1 Output
M. B2 Output
N. Electrode Pad
O. Micro USB Cable
Electrode Placement Guide Warranty
Customer Support
Neck Ankle/Foot Ankle/Foot
Shoulder Elbow Upper Arm
Upper Back Lower Back/
Lumbar
Hip
Wrist/Hand Knee/Joint Calf
Etekcity warrants all products to be of the highest
quality in material, craftsmanship, and service,
effective from the date of purchase to the end of
the warranty period. Warranty lengths may vary
between product categories.
If you encounter any issues or have any questions
about your new product, please contact our
helpful Customer Support Team. Your satisfaction
is our goal!
Distributed by Etekcity Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806
Email: [email protected]
Toll-Free: [phone]
Support Hours
Mon–Fri, 9:00 am–5:00 pm PST/PDT
*Please have your order invoice and order ID
ready before contacting Customer Support.
Note:
•Do not place electrodes on both legs or feet at the same time.
Only treat 1 at a time.
•Only place electrodes according to Electrode Placement Guide.

Using the TENS Unit
1. Connect the lead pins to the connectors on the
electrodes. Then, place the electrodes on your skin
(with the TENS unit turned OFF). Each wire has 2 leads
with pin-inserted connectors. Make sure the metal on
the pins is not exposed.
Note: Before rst use, fully charge the TENS unit.
Note: This TENS unit has 4 independent channels
(A1, A2, B1, B2). Make sure you know which
channel(s) you want to use before you connect
wires to the TENS unit.
Note: If no buttons are pressed for 3 minutes, the
TENS unit will turn off automatically.
Note:
• Intensity can be adjusted independently for A and
B channels.
• Press / repeatedly on the left side and right
side to raise or lower intensity for channel A (A1
and A2 output) and channel B (B1 and B2 output).
• Lowering both intensities to 0 will reset the timer.
Caution:
•Do not remove electrode pads by pulling on the
wire. Peel gently from any corner.
•Do not place electrodes on the carotid artery,
throat, backbone, or spine.
• If you feel pain, dizziness, discomfort, or nausea
while using the TENS unit, stop using immediately
and call your physician or medical practitioner.
Do not exceed your comfort level.
2. Insert the lead wire plugs into the sockets on the TENS
unit. You can use up to 4.
7. Press to pause the treatment at any time.
Press again to resume.
3. Press to turn on the TENS unit. Wait 2 seconds for
the TENS unit to fully turn on.
4. Select 1 of 15 therapy modes. The selected icon will
flash on the screen and show the corresponding
number.
8. Press and hold for 2 seconds to turn off the TENS
unit at any time.
9. Unplug the electrodes from the TENS unit. Then peel
the pads off the skin gently and replace on the plastic
lm. Never remove pads from skin before turning off
the TENS unit.
Note:
•You can only use 1 therapy mode at a time.
• The TENS unit will automatically default to the
last mode selected.
5. Optionally, press to increase the time by 10-minute
increments for up to 60 minutes. The time will show on
the screen. The default time is 20 minutes.
6. Press or to begin the treatment. Press again to
increase the intensity.