ETERNAL RIVAL Aegis Fighstick User manual

ETERNAL RIVAL
{Aegis} High Tier Enclosure
[Art] Fighstick/Stickless/
Keyboard Style
Manual
Hardware
1A 1B 2 3A 3B 4 5 6
Included with
additional
acrylic top
spacer (b)
Included with
additional
acrylic
bottom spacer
panel (E2)
(X) indicates the qty with additonal plexi spacer add-on
{X} indicates the qty for Aluminum Top (Aegis Case)
*Joystick hardware in a seperate ziplock bag with directions
*Brook PCB stands in a seperate ziplock bag with directions
x8(4){4}
(4)
x6
x14-18
(14){22}
x14 x14 x6
{x4}
7
(4-8)
A B
C
CC QQ
DEE2
***Will vary depnding your button layout
Mounting Top Spacer - add on Top
Inner Back Panel
Inner Front Panel
Bottom Window Bottom
(Bottom Spacer - Add on)
F1
F2
Outer
Back Panel
Outer
Front Panel
P1
P2
x2 inner
side panels
G
x2 Outer Side
panels
Joystick
Spacer
H
{Alumium Panel for Aegis
ghtstick}
Artwork if Purchased
1A
A
2
2
CCC
1A 1B
3A 7
B
QQ
A
Notice
Countersink hole
on top. Screw will be
ush to the panel.
Notice
Countersink hole
on top. Screw will be
ush to the panel.
Step 1 - Mounting joystick and PCB Step 2 - Assembling the top
3. Place at head (1a) screw into
countersink holes and
screw it to the the
metal stands (2) by hand x2
1. Place (C) on top of (A) and hold it together by hand
screwing the pillar (2) to the screw (1a) placed through
the 2 panels. -If you have artwork you will place below
top panel (c)
-If you have a spacer panel (b) use screw (1b)
-If you have the alumium plate (CC) you will have to use
screw (3A) along with the washer (7) (Panel B included
with aegis enclosure)
2. Once the top panels are assmebled you can
place the buttons in.
1. Mount the joystick*
2. Mount the Brook PCB*
*Directions in seperate ziplock bag.

1A
D
6
3A
3A
E
E2
6
4
5
3B
-If you have a extra spacer panel (E2)
use screw (3B)
Use a screw driver if needed, to push screw
through the hole.
.
Screw
Side Panels
outside
Inside
3A
45Step 3 - Assembling the sides
1. Assemble all Side panels. See (*1) Place buttons
if you like. Install neutrik device. If bowing of
the panels occur it is because the screws
were over tightened.
2. You can begin wiring now or during step 4
Use tie straps to keep wiring managed.
3. Place side panels in slots. See (*2) the tabs
on the side panels are placed into the slots.
(it should not but secure, just
place holders till next next)
GF1 F2
HP1 P2
3A
4
5
*2
*1
*1
*1
*2
Notice
Countersink hole
on top. Screw will be
ush to the panel.
Step 4 - Assembling the box Step 5 Assemble Feet
1.Place the window’s (D) slots
into the tabs of the side panels
to keep the side panels in place
See (*2)
Make sure all side panels are in its tabs (top and btm)
before inserting the screw through window (D) to the pillar
See (*1)
2. you can wire at this stage as well, a bit harder with
the window on.
X4
Step 6 Assemble Bottom Panel
Step 7 - Cover the bottom
1. Place bottom on top of
assembled enclosure. LIne up the holes
and screw it in with a screw driver.
Finished
1. If you do not
have the bottom spacer
panel (E2) still proceed
to install feet without
it.
BOTTOM COVER WITH FEET INSTALLED