EUFY RoboVac X8 Hybrid User manual

For FAQs and more information, please visit:
www.eufylife.com
51005002929 T2261 V01
Owner’s Manual
RoboVac X8 Hybrid

01
Thank you for purchasing RoboVac. Carefully read all the instructions
below before using this device, and keep this manual for future reference.
Table of Contents
02 Important Safety Instructions
17 About Your RoboVac
What's in the Box
RoboVac Anatomy
Map Navigation and Management
23 Get Started
Important Tips Before Use
Preparation
Charge Your RoboVac
Auto Recharge and Resume
26 Using Your RoboVac
Turn On / O
Start Cleaning
Use Your RoboVac with the EufyHome App
Select a Cleaning Mode
Use Your RoboVac with Amazon Alexa /
the Google Assistant
Set Up Virtual Wall / Boundary Strip
35 Cleaning and Maintenance
Clean the Dust Collector and Filter
Clean the Rolling Brush
Clean the Side Brush
Clean the Swivel Wheel
Clean the Mopping Cloth and Water Tank
41 Troubleshooting
Voice Alert
47 Customer Service
English 01
Español 49

02 03
English English
the screws on the bottom, then remove the back
cover. Remove the battery by disconnecting the quick
connector.
•The used battery should be placed in a sealed plastic bag
and disposed of safely according to local environmental
regulations.
•The external flexible cable or cord of the power supply
unit cannot be replaced; if the cord is damaged, the
power supply unit should be disposed of.
•This device is for indoor use only.
•This device is not a toy. Do not sit or stand on this device.
Small children and pets should be supervised when this
device is operating.
•Store and operate this device in room temperature
environments only.
•Do not use this device to pick up anything that is burning
or smoking.
•Do not use this device to clean up spills of bleach, paint,
chemicals, or anything wet.
•Before using this device, pick up objects like clothing and
loose paper. Lift up cords for blinds or curtains. Move
power cords, sharp-pointed and fragile objects out of the
way. If this device passes over a power cord and drags it,
an object could be pulled off a table or shelf.
•If the room to be cleaned has a balcony, a physical barrier
should be used to prevent access to the balcony and to
ensure safe operation.
•Do not place anything on top of this device.
•Be aware that this device moves around on its own.
Take care when walking in the area where this device is
operating to avoid stepping on it.
•Do not operate this device in areas with exposed
electrical outlets on the floor.
Important Safety Instructions
To reduce the risk of injury or damage, keep these
instructions at hand when setting up, using, and
maintaining this device.
WARNING SYMBOLS USED
This is the safety alert symbol. This symbol alerts you to
potential hazards that could result in property damage
and/or serious bodily harm or death.
•This device can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of this device in a safe way
and understand the hazards involved.
•Children should be supervised to ensure they do not play
with this device.
•Cleaning and maintenance shall not be performed by
children without adult supervision.
•This device is only to be used with the power supply unit
provided.
•Before cleaning or maintaining this device, the plug must
be removed from the outlet.
•The battery in this device should only be replaced by a
skilled professional.
•When removing the battery, disconnect the device from
the supply mains.
•To recharge the battery, only use the detachable
adapter (US/CA: GSCU1000S024V24T; UK:
GSCB1000S024V24T; AU: GSCS1000S024V24T; EU:
GSCV1000S024V24T) provided with this device.
•The battery must be removed before this device is
disposed of. To remove the battery, first unscrew

04 05
English English
Notice
This symbol on the device or its packaging indicates:
Do not dispose of electrical appliances as unsorted
municipal waste; use separate collection facilities.
Contact your local authority for information
regarding the collection systems available. If
electrical appliances are disposed of in landfills or
dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging
your health and well-being. When replacing old
appliances with new ones, the retailer is legally
obliged to take back your old appliance for disposal
at least free of charge.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Warning: Changes or modifications not expressly approved
by the party responsible for compliance could void the user's
authority to operate the equipment.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
•Do not expose the electronics of this device, its battery,
or the integrated Charging Base. There are no user-
serviceable parts inside.
• Do not use this device on an unfinished, unsealed, waxed
or rough floor. It may result in damage to the floor and this
device. Use only on hard floor surfaces or low-pile carpets,
and not on carpets with tasseled edges or loose threads.
•This device has been designed to be used on floors
without scratching them. We still recommend that you
test this device on a small area of the room to be cleaned
to ensure no scratches are made before cleaning the
whole room.
•Only use attachments recommended or described in this
manual.
•Do not handle the appliance or plug with wet hands.
•Ensure that the dust collector and/or filters are correctly
in-place before usage.
•Do not use a battery pack or appliance that is damaged
or modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion, or risk
of injury.
•Do not expose the battery pack or appliance to fire or
excessive temperature. Exposure to fire or temperature
above 130°C may cause an explosion.
•Do not modify or attempt to repair the appliance or the
battery pack (as applicable), except as indicated in the
instructions for use and care.
•Follow all charging instructions and do not charge the
battery pack or appliance outside of the temperature
range specified in the instructions. Charging improperly
or at temperatures outside of the specified range may
damage the battery and increase the risk of fire.
•The laser distance sensor of this device meets the
standards for Class I Laser Products in IEC 60825-1:2014
and will not generate hazardous laser radiation.

06 07
English English
Maximum output power: 18 dBm (For EU)
Frequency band: 2.4G band (2.4000GHz - 2.4835GHz)
GB Declaration of Conformity
Hereby, Anker Innovations Limited declares that the
product type T2261 is in compliance with Radio Equipment
Regulations 2017 and The Restriction of the Use of
Certain Hazardous Substances in Electrical and Electronic
Equipment Regulations 2012. The full text of the GB
declaration of conformity is available at the following
internet address: https://www.eufy.com.
Trademark Notice
•Amazon, Echo, Alexa and all related logos are trademarks
of Amazon.com, Inc. or its affiliates.
•Apple and the Apple logo are trademarks of Apple Inc.,
registered in the U.S. and other countries. App Store is
a service mark of Apple Inc., registered in the U.S. and
other countries.
•Google Play and the Google Play logo are trademarks of
Google Inc.
•Google Home is a trademark of Google Inc.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures: (1)
Reorient or relocate the receiving antenna. (2) Increase the
separation between the equipment and receiver. (3) Connect
the equipment into an outlet on a circuit dierent from that to
which the receiver is connected. (4) Consult the dealer or an
experienced radio / TV technician for help.
ISED Compliance Statement
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
RF Exposure Compliance Statement
This equipment complies with FCC/IC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a
minimum distance of 20cm between the radiator and your
body.
Declaration of Conformity
This product complies with the radio interference
requirements of the European Community. Hereby, Anker
Innovations Limited declares that the radio equipment type
T2261 is in compliance with Directive 2014/53/EU. The full
text of the EU declaration of conformity is available at the
following internet address: https://www.eufylife.com/.

08 09
English English
damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
In order to claim the warranty, you must return the
product to the retailer from which it was purchased or if
that retailer is part of a National network, a store within
that chain, along with satisfactory proof of purchase. The
retailer will then return the goods to Directed Electronics
Australia authorized by Anker Innovations Limited. Directed
Electronics Australia will repair, replace or refurbish the
product at its discretion. The retailer will contact you when
the product is ready for collection. All costs involved in
claiming this warranty, including the cost of the retailer
sending the product to Directed Electronics Australia, will
be borne by you.
This warranty is offered by Directed Electronics Australia.
Customer service support number ([phone]
Mon-Fri 8:30am - 5:00pm (AEST) and customer service
email address [e-mail].
AUSTRALIA & NEW ZEALAND WARRANTY
This document details the terms and conditions of the
warranty provided with this product. Please disregard any
other representations contained on this product’s packaging
or provided with this product, which constitute or appear to
constitute a warranty.
Subject to the exclusions and limitations set out below, we
warrant to you that if you purchase a product directly from
us, or, from any of our authorized resellers, that it will not
contain defects which are a result of faulty manufacturer
workmanship or materials. This warranty subsists for
15 months from the date of purchase. This warranty is
provided in addition to your rights under the Australian &
New Zealand Consumer Law.
Subject to any rights you have under the Australian &
New Zealand Consumer Law, we will not be liable for
defects which are a result of damage or loss caused by
factors beyond our control, any product which has not
been maintained according to any care or maintenance
instructions provided with the product, any alterations
to a product which are not performed by us, or damage
or defects caused to the product due to unusual or non-
recommended use. We will not be liable for any special,
indirect, consequential or economic loss or damage or loss
of profits whatsoever suffered by you or any other person
resulting from any act or omission by us. Our total liability
in respect of this Warranty against Defects is limited to the
replacement of the goods.
This Warranty against Defects is provided in addition to
other rights and remedies that you may have at law. Our
goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for
compensation for any reasonably foreseeable loss or

10 11
Français Français
GSCS1000S024V24T; UE : GSCV1000S024V24T)
fourni avec cet appareil.
•La batterie doit être retirée de cet appareil avant de le
mettre au rebut. Pour retirer la batterie, desserrez les vis
du fond, puis retirez le capot arrière. Retirez la batterie en
débranchant le connecteur rapide.
•La batterie usagée doit être placée dans un sac en
plastique hermétique et éliminée en toute sécurité,
conformément aux réglementations environnementales
locales.
•Le câble flexible externe ou le cordon du bloc
d'alimentation ne peut pas être remplacé ; si le cordon
est endommagé, l'unité d'alimentation doit être éliminée.
•Cet appareil est destiné exclusivement à une utilisation
en intérieur.
•Cet appareil n'est pas un jouet. Veillez à ne pas vous tenir
debout ou assis sur cet appareil. Les jeunes enfants et
les animaux de compagnie doivent être surveillés lors du
fonctionnement de cet appareil.
•Entreposez et utilisez cet appareil dans des
environnements à température ambiante.
•N'utilisez pas cet appareil pour ramasser tout élément en
train de brûler ou fumant.
•N'utilisez pas cet appareil pour nettoyer des
déversements d'eau de javel, de peinture, de produits
chimiques ou quoi que ce soit d'humide.
•Avant d'utiliser cet appareil, ramassez les objets tels
que les vêtements et les feuilles de papier. Relevez les
persiennes ou les rideaux proches du sol. Enlevez du
passage les cordons d'alimentation ainsi que les objets
pointus et fragiles. Si cet appareil passe au-dessus d'un
cordon d'alimentation et le traîne avec lui, un objet peut
tomber d'une table ou d'une étagère.
Consignes de sécurité importantes
Pour réduire le risque de blessure ou de dommage, gardez
ces consignes de sécurité à portée de main lors de la
configuration, l'utilisation et l'entretien de cet appareil.
SYMBOLES D'AVERTISSEMENT UTILISÉS
Il s'agit du symbole d'avertissement de sécurité. Ce
symbole vous alerte sur les dangers potentiels qui
peuvent entraîner des dommages matériels et/ou des
lésions corporelles graves ou la mort.
•Cet appareil peut être utilisé par des enfants âgés de
8 ans et plus, ainsi que des personnes présentant des
capacités physiques, sensorielles ou mentales réduites,
ou un manque d'expérience et de connaissances,
si celles-ci sont sous surveillance ou ont reçu les
instructions d'utilisation de cet appareil et comprennent
les risques encourus, et l'utilisent dans un endroit sûr.
•Les enfants doivent être surveillés afin de s'assurer qu'ils
ne jouent pas avec cet appareil.
•Le nettoyage et l'entretien ne doivent pas être effectués
par des enfants sans la supervision des adultes.
•Cet appareil doit uniquement être utilisé avec le bloc
d'alimentation fourni.
•Avant de nettoyer ou d'entretenir cet appareil, vous
devez le débrancher de sa prise d'alimentation.
•La batterie de cet appareil ne doit être remplacée que par
un professionnel qualifié.
•Lors du retrait de la batterie, débranchez l'appareil du
secteur.
•Pour recharger la batterie, n'utilisez que l'adaptateur
détachable (États-Unis/Canada : GSCU1000S024V24T;
R-U : GSCB1000S024V24T; AUS :

12 13
Français Français
•N'exposez pas la batterie ou l'appareil au feu ou à des
températures excessives. L'exposition au feu ou à une
température supérieure à 130°C peut provoquer une
explosion.
•Ne modifiez pas et n'essayez pas de réparer l'appareil ou
la batterie (si applicable), sauf si cela est indiqué dans les
instructions d'utilisation et d'entretien.
•Suivez toutes les instructions de charge et ne chargez
pas la batterie ou l'appareil en dehors de la plage de
température indiquée dans les instructions. Une charge
incorrecte ou à des températures hors de la plage
spécifiée peut endommager la batterie et augmenter le
risque d'incendie.
•Le capteur de distance laser de cet appareil est
conforme aux normes pour les produits laser de classe I
de la norme IEC 60825-1:2014 et ne génère pas de
rayonnement laser dangereux.
•Si la pièce à nettoyer possède un balcon, une barrière
physique doit être utilisée pour empêcher l'accès au
balcon et garantir un fonctionnement sécurisé.
•Veuillez ne rien placer sur le dessus de cet appareil.
•Gardez à l'esprit que cet appareil se déplace par ses
propres moyens. Faites attention en marchant dans la
zone où cet appareil fonctionne, afin d'éviter de marcher
dessus.
•N'utilisez pas cet appareil dans des zones avec prises
électriques exposées sur le plancher.
•N'exposez pas l'électronique de cet appareil, de sa
batterie ou de la base de chargement intégrée. L'appareil
ne contient aucune pièce réparable par l'utilisateur.
•N'utilisez pas cet appareil sur un sol inachevé, non
vitrifié, ciré ou rugueux. Cela peut entraîner des
dommages sur le sol et cet appareil. N'utilisez cet
appareil que sur les sols durs et les tapis ras, et non sur
les tapis avec des glands ou des franges.
•Cet appareil a été conçu pour être utilisé sur des
planchers sans le rayer. Nous vous recommandons de
toujours tester l'appareil sur une petite zone de la pièce à
nettoyer, avant de nettoyer la salle entière, pour s'assurer
qu'aucune rayure n'apparaisse.
•Utilisez uniquement les accessoires recommandés ou
décrits dans ce manuel.
•Ne manipulez pas l'appareil ou la fiche avec les mains
mouillées.
•Assurez-vous que le sac à poussière et/ou les filtres sont
en place avant utilisation.
•N'utilisez pas de batterie ou d'appareil endommagé
ou modifié. Les batteries endommagées ou modifiées
peuvent présenter un fonctionnement imprévisible
risquant d'entraîner un incendie, une explosion ou des
blessures.

14 15
Français Français
interference in a residential installation.
Cet appareil génère, utilise et peut émettre des fréquences
radio qui peuvent causer des interférences nuisibles aux
radiocommunications si l’appareil n’est pas installé et
utilisé conformément aux instructions. However, there is
no guarantee that interference will not occur in a particular
installation.Si cet appareil provoque des interférences
nuisibles à la réception de la radio ou de la télévision, ce
qui peut être déterminé en mettant en route l'appareil et
en l'arrêtant, il est recommandé d'essayer de corriger les
interférences en prenant l'une ou plusieurs des mesures
suivantes : (1) réorienter ou déplacer l'antenne de réception ,
(2) Increase the separation between the equipment and
receiver. (3) Connect the equipment into an outlet on a
circuit dierent from that to which the receiver is connected.
(4) consulter le revendeur ou un technicien expérimenté en
radio/télévision pour obtenir une assistance.
L’émetteur/récepteur exempt de licence contenu dans
le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
Déclaration de conformité avec les normes d'exposition
aux RF
Cet équipement est conforme aux limites d'exposition aux
radiations FCC/IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec
une distance minimum de 20 cm entre le radiateur et votre corps.
Avis
Ce symbole sur le produit ou son emballage
indique :
Ne jetez pas les appareils électriques de la même
manière que les déchets municipaux non triés ;
utilisez une infrastructure de collecte séparée.
Contactez directement votre commune pour
plus d'informations concernant les systèmes de
collecte disponibles. Si des appareils électriques
sont jetés dans des décharges ou des dépotoirs,
des substances dangereuses peuvent s'infiltrer
dans les eaux souterraines et entrer dans la chaîne
alimentaire, nuire à votre santé et votre bien-être.
Quand vous remplacez vos anciens appareils par
de nouveaux, le détaillant est légalement obligé
de reprendre votre ancien appareil pour son
élimination, au minimum gratuitement.
Déclaration FCC
Cet appareil est conforme à la partie 15 du règlement de la
FCC. Le fonctionnement est soumis aux deux conditions
suivantes : (1) l'appareil ne doit pas produire d'interférences
nuisibles, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si celui-ci est
susceptible d'en compromettre le fonctionnement.
Avertissement : les changements ou les modifications
non expressément approuvés par la partie responsable
de la conformité pourraient entraîner une annulation de
l'autorisation d'utilisation de l'équipement.
Remarque : cet appareil a été testé et déclaré conforme aux
limites d’un appareil numérique de Classe B conformément
au Chapitre 15 de la réglementation FCC. These limits are
designed to provide reasonable protection against harmful

17
English
16
Français
About Your RoboVac
What's in the Box
RoboVac Charging Base Power Adapter
Additional Filter
Owner’s Manual &
Other Documents
Waterproof Pad
Water Tank Washable Mopping
Cloth Disposable Mopping Cloths (x5)
Additional Side Brush Cable Ties (x5)
Déclaration de conformité
Ce produit est conforme aux exigences en matière
d'interférences radio de la Communauté européenne.
Par les présentes, Anker Innovations Limited déclare
que l'équipement radio de type T2261 est conforme à la
directive 2014/53/UE. Le texte complet de la déclaration de
conformité à la réglementation européenne est disponible à
l'adresse Internet suivante : https://www.eufylife.com/.
Puissance de sortie maximale : 18 dBm (pour l'UE)
Bande de fréquence : Bande 2,4 G (2,4000 GHz -
2,4835 GHz)
Avis de marque commerciale
•Amazon, Echo, Alexa et tous les logos associés sont des
marques commerciales d'Amazon.com, Inc. ou de ses
filiales.
•Apple et le logo Apple sont des marques déposées
d'Apple Inc., enregistrées aux États-Unis et dans d'autres
pays. App Store est une marque de service d'Apple Inc.,
enregistrée aux États-Unis et dans d'autres pays.
•Google Play et le logo Google Play sont des marques de
Google Inc.
•Google Home est une marque de Google Inc.

18 19
English English
C. Dust Collector
Filter
Cleaning tool
D. Suction Inlet
Dust collector
Suction inlet Suction inlet
E. Charging Base
Power cord storage
compartment
Slot winding
Wire slot exit
Charging contact pins
Power socket
Status light
RoboVac Anatomy
A. Top & Side
Recharge button
Bumper
Wi-Fi status light
Laser distance sensor
(LDS)
Spot cleaning button
&
Auto cleaning Start / Pause button
• Press to return RoboVac to the
Charging Base; press again to pause
• Press to start Spot cleaning
• Press and hold both buttons
for 5 seconds to restore factory
settings
• Press and hold for 3 seconds to turn on
or o (when not in Charging status)
• Press to start Auto cleaning
• Press to pause the current task when
working
Wall sensor
Ventilation holes
Dust collector
release button
Water tank
Front infrared sensor
Dust collectorWashable
cleaning cloth
B. Bottom
Charging contact pins
Swivel wheel
Battery compartment
Rolling brush
Side brush
Drop sensors
Wheels
Brush guard
Water tank
Washable cleaning cloth

20 21
English English
Buttons & Indicators
Turn on / o (Press and hold for 3 seconds)
Start / Paused Cleaning
• Solid blue: standby, cleaning, paused cleaning, returning to
charging base or fully charged
• Solid orange: working in low battery status
• Pulsing orange (when docked to Charging Base): charging
• Flashing red: error
* Refer to the “Troubleshooting > Voice Alert” section in this
manual for solutions.
Returning to Charging Base
• Flashing blue slowly: returning to Charging Base
• Solid blue: standby or paused
Start / Paused Spot Cleaning
• Flashing blue slowly: Spot Mode
• Solid blue: standby or paused
• When you use the Find My Robot function via the EufyHome app, all three
LED indicators are solid blue and a voice prompt is heard.
• To conserve power, the blue light on the buttons becomes dim when:
• RoboVac is not docked to the Charging Base and has been inactive for 10
minutes;
• RoboVac is fully charged for 1 minute.
(Wi-Fi Status Light) Status
Slowly flashing blue Waiting for connection
Rapidly flashing blue Connecting with your wireless router
Solid blue Connected to your wireless router
F. Water Tank
Slot
Water tank filter
Cloth attachment area
Snap joints Snap joints
Water inlet
cover
Water inlet
Washable cleaning cloth

22 23
English English
• When using for the first time, make sure RoboVac starts cleaning from the
Charging Base.
• During cleaning, do not move RoboVac frequently. If moved, place RoboVac
back to the original position.
Get Started
Important Tips Before Use
abc
def
Remove power cords and small objects from the floor that may entangle RoboVac.
Use the supplied cable ties to organize your wires and power cords.
Fold tasseled edges of area rugs underneath to prevent tangling RoboVac. Avoid
cleaning very dark-colored high-pile rugs or rugs thicker than 1.02 in / 26 mm as
they may cause RoboVac to malfunction.
The “No-Go” zones that you set may be ineffective in some cases. It is strongly
recommended to place boundary strips (sold separately) in front of fireplaces and
certain areas (i.e. air vents) that may cause damage to RoboVac if entered.
Keep RoboVac away from wet areas during cleaning..
RoboVac may climb on top of objects less than 0.67 in / 17 mm in height. Remove
these objects if possible.
Anti-drop sensors will prevent RoboVac from tumbling downstairs and steep drops
in most cases. Sensors are less effective if dirty or used on carpeted/reflective/very
dark-colored floors. It is recommended to place physical barriers to block off areas
where RoboVac may fall.
Map Navigation and Management
Navigation
Once Auto cleaning starts, RoboVac moves from the Charging Base, automatically scans
to generate maps, intelligently determines its cleaning route, and divides the space into
zones. The cleaning paths are planned along the walls, following a Z-shaped cleaning
method to complete the cleaning of each zone one by one.
Real-time Mapping & Floor plan
Real-time mapping helps RoboVac to learn the correct cleaning path and the environment
of your home easily. A floor plan will be built after cleaning. The map will be updated in
real-time during each cleaning session to ensure normal navigation.
To create a complete floor plan:
1. Open your doors so that RoboVac can map each room.
2. Remove any objects that may be in the way or that might entangle RoboVac.
Repositioning & Remapping
If the position of RoboVac / Charging Base is adjusted or the surroundings are changed
significantly, RoboVac will try to reposition and remap to match the surroundings.
• If the repositioning is successful, RoboVac will resume cleaning.
• If the repositioning fails, RoboVac will remap to ensure normal navigation with a new
cleaning.

24 25
English English
• Install the Charging Base in a location that RoboVac can easily access.
It is recommended to place the Charging Base against a wall, and on a
hard-level surface rather than on rugs or carpets.
• Always keep the Charging Base plugged in, otherwise RoboVac will not
automatically return to it.
• To ensure proper charging, do not frequently move the Charging Base.
When its location is changed, RoboVac may remap due to repositioning
failure (see About Your RoboVac > Map Navigation and Management
for details).
Charge Your RoboVac
• Make sure RoboVac is fully charged before use.
• RoboVac will return to the Charging Base at the end of a cleaning cycle or when its
battery is running low.
Method 1: Attach RoboVac to the Charging Base by aligning its charging pins with the
charging pins on the base.
Method 2: Press on the main unit or tap the icon in the EufyHome app to send
RoboVac to the Charging Base.
Preparation
1
Remove the foam blocks beside the bumper before use.
2
Place the Charging Base on a level surface and against a wall.
3
Remove objects within 3 ft / 1 m of the left and right side and within 6 ft / 2 m of
the front of the Charging Base. If you cannot remove the objects, move RoboVac
to a new place and check whether RoboVac can return to the Charging Base
normally; if not, contact eufy customer service for help.
4
Connect the adapter to the Charging Base and a wall outlet.
When the Charging Base connects to AC power, the LED indicator on the
Charging Base is SOLID WHITE.
1 2 3

26 27
English English
1
Press to start cleaning in Auto cleaning mode.
RoboVac moves around to scan the environment and builds a map
automatically.
2
Press again to pause cleaning.
Press to resume cleaning.
When cleaning is paused, docking RoboVac onto the Charging Base will stop
the cleaning.
If cleaning is paused for 10 minutes, RoboVac automatically stops cleaning and
switches to sleep mode.
3
Press to stop current cleaning and return to the Charging Base.
Before cleaning, tidy cables and cords to avoid power interruption or any
damage caused by pulling the cord during cleaning.
Use Your RoboVac with the EufyHome App
To fully enjoy all the available features, it is recommended to control your RoboVac via
the EufyHome app.
Before you start, make sure that:
• Your smartphone or tablet is running iOS 9.0 (or above) or Android 5.0 (or above).
• The 2.4GHz band wireless signal is enabled on your wireless router.
• The Wi-Fi status light on RoboVac is slowly flashing blue.
• Your smartphone or tablet has enabled Bluetooth to ensure a better connection.
• RoboVac has enough power during setup.
• If RoboVac is not used for a long time, to preserve the battery’s lifespan,
recharge at least once every 6 months.
• When RoboVac is being charged, to enter Reduced Power Standby mode
for power-saving, simultaneously press and hold the three buttons (
& & ) on RoboVac for 10 seconds until the lights turn off. Wi-Fi
is disabled while this mode is active. Press to exit Reduced Power
Standby mode.
Auto Recharge and Resume
RoboVac returns to the Charging Base automatically to recharge when:
• RoboVac has finished cleaning;
• Cleaning is not complete and the battery level becomes low; once recharged to
80% battery capacity, RoboVac will resume and finish the remaining cleaning.
Do not move the Charging Base during cleaning, otherwise RoboVac may
fail to return for recharge. If failed, you have to manually attach it to the
Charging Base. If the Charging Base is moved, start cleaning from the new
location. RoboVac will automatically return when it has finished cleaning.
Using Your RoboVac
Turn On / Off
• RoboVac turns on automatically when attached to the Charging Base and connected
to power.
• When RoboVac is not on the Charging Base, press and hold for 3 seconds to
turn on the main unit. Wait until the Power Status Light turns solid blue.
• When RoboVac is not on the Charging Base, press and hold for 3 seconds again
to turn off the main unit.
Start Cleaning
RoboVac cannot start cleaning if the battery level is low. In this case,
recharge RoboVac first before cleaning.

28 29
English English
Schedule Cleaning
With the EufyHome app, you can schedule RoboVac to start cleaning at a particular
time.
You can set the time and customize the cleaning schedules from Sunday to
Saturday on the EufyHome app. This function is available in the app only.
Select a Cleaning Mode
• You can press at any time to pause the current cleaning cycle.
• You can also select a cleaning mode via the EufyHome app.
Auto Cleaning Mode
1. Press to start cleaning in Auto cleaning mode.
2. Press again to pause cleaning.
By default, RoboVac starts in Auto cleaning mode when it is turned on.
EufyHome
1. Download the EufyHome app from the App Store (iOS devices) or Google Play
(Android devices).
2. Open the app and create a user account.
3. Tap the “+” icon to add “RoboVac X8 Hybrid” to your EufyHome account.
4. Follow the instructions in the app to set up the Wi-Fi connection.
After connecting successfully, you can control RoboVac via the app.
With the app, you can select cleaning at your desired suction level, schedule
cleaning, view the cleaning map, set up “No-Go” zones, check the network
connection status, and access additional features.
Wi-Fi Status Light
Slowly flashing blue Waiting for connection
Rapidly flashing blue Connecting with your wireless router
Solid blue Connected with your wireless router
If RoboVac gets stuck in any space, tap Find My Robot in the app to find
the machine. This function is available in the app only.
Reset the Wi-Fi connection
To reset the Wi-Fi connection, press and hold the two buttons ( and )
simultaneously for 5 seconds until you hear a voice prompt. At the same time,
RoboVac will restore the factory default settings.
You will hear a voice prompt when the Wi-Fi connection has been reset, and
the Wi-Fi status light will slowly flash blue. Now you can follow the Wi-Fi
instructions in the eufyHome app to set up the Wi-Fi connection.

30 31
English English
Zone Cleaning Mode (available via the EufyHome app only)
In this mode, you can set up a cleaning zone in the EufyHome app. RoboVac will clean
the selected zone only.
Select a Suction Power Level
In the EufyHome app, select a suction power level according to your needs:
• Quiet
• Standard (Default)
• Turbo
• Max
Select BoostIQ™ feature
In the EufyHome app, select the BoostIQ™ feature according to your needs. RoboVac
will automatically increase the suction power if it detects that stronger power is
needed to ensure the best clean. BoostIQ™ is ideal for cleaning thicker carpets and
hard-to-sweep messes, which will reduce the total cleaning time, but increase the
noise level. If the vacuuming noise caused by BoostIQ™ disturbs you, you can disable
this feature.
Use Mopping System
• The mopping mode is only intended for a clean floor without stubborn
stains or liquids. To avoid staining floors, do not use the mopping
function when dust is mixed with liquids such as coffee or ink.
• Mopping System cleans best on smooth hard surfaces and may
not perform so well on uneven tiles, heavily waxed floors or rough
surfaces like slate or brick, which may snag the cleaning pad.
• The mopping mode is not recommended when no one is at home.
• Do not use the mopping mode on a carpeted floor. It is recommended
to set a “No-Mop” zone in the EufyHome app to avoid cleaning the
carpeted area.
1. Before mopping, install the waterproof pad under the Charging Base to protect the floor.
Spot Cleaning Mode
RoboVac intensively cleans a specific area with a size of 4.9 ft x 4.9 ft / 1.5 m x 1.5 m,
useful if there is a concentrated area of dust or debris. When the cleaning of a certain
zone is finished, it automatically returns to the Charging Base.
4.9 ft / 1.5 m
4.9 ft / 1.5 m
Press to start Spot cleaning.
Room Cleaning Mode (available via the EufyHome app
only)
In this mode, your house is automatically divided into several rooms for cleaning in the
EufyHome app. You can also customize your room settings in the app. RoboVac will
clean the selected rooms only and return to the Charging Base after cleaning.
• Start Room cleaning only after RoboVac has created the map.
• It is recommended that RoboVac moves from the Charging Base to start
Room cleaning.

32 33
English English
5. Select a cleaning mode to start cleaning.
RoboVac automatically sweeps and mops in the selected mode.
6. When RoboVac finishes working and returns to the Charging Base, remove the
water tank, empty any remaining water, and clean the mopping cloth to prevent
mildew or unpleasant smells. The disposable mopping cloth is for single-use only. For
how to clean and maintain the water tank, refer to the “Cleaning and Maintenance”
section in this manual.
Use Your RoboVac with Amazon Alexa /
the Google Assistant
Amazon Alexa and the Google Assistant are smart voice assistants that enable you to
control RoboVac with your voice.
Before you start, make sure that:
• RoboVac is attached to the Charging Base to ensure there is enough power.
• RoboVac is connected with the EufyHome app.
• You have an Alexa-enabled device (i.e. Amazon Echo, Echo Dot and Amazon Tap,
Echo Show, Echo Spot) or a device enabled with the Google Assistant (i.e. Google
Home, Google Home Mini). These devices are sold separately.
• The Amazon Alexa app or Google Home app is already installed on your smart
device, and you have created an account.
To control RoboVac with Amazon Alexa or the Google Assistant
1. Open the EufyHome app and tap “Smart Integrations” in the top left.
2. Follow the on-screen instructions to complete the setup.
Currently this feature only supports English, German, French, and
Spanish. You can check regularly if more languages are supported at
https://www.eufylife.com/support/.
2. Wet the mopping cloth and wring it until it does not drip. Insert the cloth along the
bracket slot and stick it firmly.
• Use either the washable mopping cloth or the disposable cloth for mopping.
3. Open the water inlet cover to fill the water, then close the cover.
• Do not use any cleaning solution other than those specified by eufy, as it
may damage RoboVac.
4. Install the water tank into the bottom of RoboVac until a click is heard.
• The mopping mode is only intended for a clean floor without stubborn
stains. To achieve a better mopping effect, it is recommended to clean
the floor with RoboVac three times before installing the mopping
module.

34 35
English English
Cleaning and Maintenance
Before cleaning and maintaining, turn off the device and unplug the adapter.
For optimal performance, follow the instructions below to clean and maintain RoboVac
regularly. The cleaning / replacement frequency will depend on your RoboVac usage
habits.
Recommended Cleaning / Replacement Frequency
RoboVac Part Cleaning Frequency Replacement Frequency
Dust Collector After each use -
Filter Once every week Every 3 months
Rolling Brush Once every week Every 6-12 months
Side Brush Once every month Every 3-6 months (or when
visibly worn)
Brush Guard Once every month Every 3-6 months (or when
the silicone rubber strip on the
brush guard becomes visibly
worn)
Sensors Once every month -
Charging Pins Once every month -
Swivel Wheel Once every month -
Water Tank After each use -
Washable
Mopping Cloth
After each use -
Water Tank
Filters
- Every 6 months (or when they
become yellow)
Set Up Virtual Wall / Boundary Strip
Virtual Wall (Available on the App Only)
In the EufyHome app, you can set up a “No-Go Zone” or “Virtual Wall” as a restricted area.
This eliminates the need to use physical barriers, including Boundary Strips. This feature is
only designed for dividing the cleaning zones, not for isolating hazardous areas.
• No-Go Zone: RoboVac will not enter the zone to vacuum.
• Virtual Wall: RoboVac will not cross the virtual wall.
• To set a virtual wall, RoboVac must initially perform a cleaning run to
create a floor plan.
• Although a virtual wall is set, RoboVac may still enter the restricted zone
due to repositioning failure or abnormal sensors.
• Moving the device or changing the environment may lose the virtual wall
and cause mapping to fail and rebuild.
Boundary Strips
Boundary strips (sold separately) can keep RoboVac away from hazardous areas.
RoboVac will recognize the barriers and will not cross into the blocked-off area.
1. Identify the area or item you do not want RoboVac to get close to.
2. Place the boundary strips FLAT on the floor or under a rug.
• Do not place the boundary strips under a THICK rug as RoboVac may fail to
recognize the boundary strip.
• Make sure the boundary strips are placed on the same surface plane
RoboVac is used on.
• If the boundary strips roll up, remove and then re-apply to the floor with
adhesive tape. Otherwise the boundary strips may not work well.

36 37
English English
6
Air-dry the dust collector and filter completely before next use. You may use
another filter if the original one is not dry.
24h
7
Place the filter back into the dust collector.
8
Push the dust collector back into the main unit.
Clean the Rolling Brush
1
Pull on the release tabs to unlock the brush guard as shown.
2
Lift the rolling brush to remove.
3
Clean the rolling brush with the cleaning tool.
4
Reinstall the rolling brush by inserting the fixed protruding end first and then
clicking into place.
5
Press down to snap the brush guard into place.
Clean the Dust Collector and Filter
1
Press the dust collector release button to pull the dust collector out.
2
Open and empty the dust collector.
3
Remove the filter.
4
Clean the dust collector and filter with the cleaning brush.
5
Rinse the dust collector and filter thoroughly with water.
1min