Eureka Hex Screen House User manual

Assembly Instructions for the Hex Screen House:
fig.6
fig.4
fig.2
fig.3
fig.1
fig.5
fig.7
www.eurekatent.com
1.800.572.8822
REV E 10.09
You can usually assemble this screen house alone. However,
with first time set-up or with windy conditions, you will
need help.
Component List:
1 Screen/Body w/ Hub 1 Tent Bag 1 Pole Bag
6 Rafters 6 Poles 1 Stake Bag and Stakes
Layout the Parts
• Unpack the tent bag, pole bag and separate all of the
components. Choose a suitable place and unroll and
unfold the fabric with the Eureka! label up.
• Assemble all of the chain-corded poles and rafters. Check
and make sure that each section is fully seated into the
next. See fig.2.
Important: Locate the hub fitting attached to the center of
the tent roof. Align the hub arms to match the layout of the
corner pins without twisting the fabric. See fig.1.
Fit the Rafters
• Slide a rafter section labeled
"TOP" onto a hub arm.The
spring clip must engage the
slot in the hub arm. Repeat
with the remaining until all
rafters are secured in place.
See fig.3.
• Make sure the hub and
fabric are still aligned.
Raise the Frame
• Insert the corner ring & pin into the bottom section of a pole.
See fig.4. Then fit the top of the pole into the elbow of its
coresponding rafter.
• With a second pole, fit it into the diagonal opposite rafter and
pin to form and arch. Lift the arch, and working your way
around the frame, attach the remaining poles to erect a
free standing unit.
See fig. 5.
Attach the Fabric to the Frame
• Attach all of the top pole clips first. It may be necessary
to open the doors and step inside the shelter to reach
the clips. Then, attach all side clips. See fig.6.
• Stake down all corner rings and your Screen House is
ready. See fig.7.
Take down
• Zip the door closed.
• Unstake the screen house.
• Unclip the fabric from the frame.
• Remove the corner pins from the ends of the
poles and remove from the rafters.
• Remove the rafters from the hub. Collapse
the sections and store in the pole bag.
• Fold the fabric into thirds. Place the pole
bag on the fabric and together, roll them up.
• Pack all components into the storage bag.

REV E FEB.09
LIMITED WARRANTY FOR THE STEEL POLE SHELTERS:
Johnson Outdoors Gear LLC Screen Houses are warranted to the original purchaser that
they are free from major defects in materials or workmanship for three years, except as
qualified below. We are not responsible for normal wear and tear or for damages
caused by shipping, accidents, misuse, alterations, or improper installations.
Additionally, although we manufacture Johnson Outdoors Gear LLC products with
quality fabrics, we are not responsible for the negative effects of climate, pollution, acts
of God, and long or semi-permanent installations. Because these shelters are temporary
structures, it is necessary that any Johnson Outdoors Gear LLC shelter be installed and
maintained according to the manufacturer’s instructions.
What Johnson Outdoors Gear LLC Will Do:
If after inspection we find that a product failed due to a manufacturing or material defect,
we will repair or replace the product, at our option, without charge.
How to Obtain Warranty Service:
Return the product, freight prepaid, to the Eureka! Dealer from whom it was purchased;
or, contact Eureka’s Customer Satisfaction Department for return authorization: toll free
1-800-572-8822. Collect shipments or shipments without return authorization cannot
be accepted. The product registration card packaged with our product need not be
returned for the warranty to be effective and for you to receive warranty service.
THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE TERMS OF THIS
LIMITED WARRANTY. IN NO EVENT SHALL JOHNSON OUTDOORS GEAR LLC BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
How State Law Relates To This Warranty:
This warranty gives you specific legal rights, and you may have other rights that vary from
state to state.
CAUTION:
Good judgment and common sense must be used for each installation and take down.
Since weather is unpredictable, it is the responsibility of the individual installing the
shelter to determine the proper time and method to install, secure and dismantle the
shelter. Johnson Outdoors Gear LLC shelter products are manufactured for use as
temporary protection from sun and light rain. Evacuate the shelter in threatening or
severe weather.
WARNING:
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS SHELTER FABRIC.
This shelter meets the flammability requirements of CPAI-84. The fabric may burn if left in
continuous contact with any flame source. The application of any foreign substance to the fabric
may render the flame-resistant properties ineffective.
To learn more…
WWW.LNT.ORG
LEAVE NO TRACE
Seven General Principles
1. PLAN AHEAD AND PREPARE
2. TRAVEL & CAMP ON DURABLE SURFACES
3. DISPOSE OF WASTE PROPERLY
4. LEAVE WHAT YOU FIND
5. MINIMIZE CAMPFIRE IMPACTS
6. RESPECT WILDLIFE
7. BE COURTEOUS OF OTHER VISITORS
JOHNSON OUTDOORS GEAR LLC
GUYLINES:
Should winds or storms arise, do not count on staking alone to keep your shelter secure. It’s important
to put in the extra time to guying out. Correctly done, it can save your shelter during exceptional
weather. Attach parachute cord [ not provided ] to the corner hooks and stake it to the ground three or
four feet from the edge of the shelter.
ULTRAVIOLET LIGHT:
Ultraviolet light damage to the shelter fabric is caused by excessive exposure to sunlight. While our
fabrics are UV resistant, any synthetic fabric is susceptible to UV degradation. UV damage will cause
nylon and polyester to become brittle and tear easily. UV damage can be minimized by erecting
shelters on sites with low exposure to direct sunlight.
CLEANING:
• Clean the shelter by setting it up and wiping it down with a mild soap (liquid hand soap) and
lukewarm water solution. Rinse thoroughly and dry completely. Never use detergent, washing
machines or dryers because they can damage the tent’s protective coating and seams. After cleaning,
be sure the shelter is completely dry, especially the heavier, double-stitched areas such as the seams,
before storing or mold and mildew are likely to grow.
• Clean the poles with a cloth and lubricate them with silicone spray. This is especially necessary after
ocean side camping trips to remove salt spray so the poles don’t corrode or stay gritty.
ALTERATIONS OR MODIFICATIONS:
DO NOT misuse, modify or alter this product in any way from its condition at the time of sale. Alteration,
modification or any use of this product contrary to the accompanying written instructions shall void the
warranty. Moreover, any misuse, alteration or modification of the product shall absolve Johnson
Outdoors Gear LLC. of any liability for property damages or injuries sustained as a result of such
misuse, modification or alteration.