Eurocave 059 User manual

Wine cabinet installation
Flush-fitting diagrams - Compact 59
www.eurocave.co.uk
Compact Range
Dimensions to be observed
See chapter “Adjusting the feet and securing the cabinet”
50 mini
1802 mini
594
600
570 mini
1797 mini
A
C
B
540 mini
059 259
259: It is essential that the unit
inside which the cabinet will be
fitted has an opening at the top, at the
back, measuring at least 540mm in length
and 50mm in width (see technical door
diagram).
A max. A min. A max. A min. B C min.
with raising piece*with raising piece*
059 853 837 896 880 548 842
259 1813 1797 1856 1840 565 1802
.for a technical door
600
560
mini
594
837-853
548
503
113
837
726
495
47
A
837-853
A
C
B
B
25
47
69,5
600
560
mini
594
837-853
548
503
113
837
726
495
47
A
837-853
A
C
B
B
Weight of
door face:
15 Kg max.
Weight of
door face:
17,5 Kg max.

www.eurocave.co.uk
Compact Range
.tnevriatnorfehttcurtsboreveN
This could result in poor functioning
of the cabinet.
On the side of the axis of rotation
of the door, position it at least 3 mm
from the adjacent unit.
The plug must be accessible after the appliance has been
installed. For medium and large models, it is essential that
the cabinet is fastened to the unit. Check that the appliance
is securely fastened to the unit and that the unit is securely
fastened to the wall.
If your door is glazed, never place it on its side as it may
break.
The wine cabinet’s 4 feet can be adjusted in height.
.tuhssniamerroodehttahtgnirusne,sdrawrofecnailppaehttliT.tehcas”seirossecca“ehtnideilppus)8(seceipgnisiarlanogaxehehtesu,yrassecenfI-
Unscrew the back feet and t the raising pieces,using a 17 mm open-ended spanner. Screw the 2 back feet onto the raising pieces.
Repeat the procedure for the 2 front feet,this time tilting the appliance backwards.
- Use suitable screws to secure the wine cabinet underneath the work top or inside the unit via the holes provided in the hinges.
(to be carried out only when the cabinet is empty)
8
- Position the cabinet so that it is level underneath the work top or inside the unit
- Open the cabinet door to 90°
- Fasten the door face of the kitchen unit onto the cabinet door (8 screws supplied)
- Ensure that the seal is completely air tight
Size 059 259
Tech door height (in mm) 676 1656
Tech door width (in mm) 592 592
Tech door thickness (in mm) 29 29
Seal thickness (in mm) 10 10
Total thickness (in mm) 39 39
Max.weight of door face (in kg) 17.5 17.5
Door face + door total weight (in kg) 16 39.5
N.B.!
.the air vent
.rotation of the door
.access to the plug
.glass door
Adjusting the feet and securing the cabinet
Fastening a unit door to a technical door
Do not
obstruct
Wine cabinet installation
Flush-fitting diagrams - Compact 59
- Your panel must be 726 mm high

1) Remove the top hinge, fit the technical cross angle (support of the top
technical hinge) on the top panel of the cellar (3 screws per side).
2) Fit the top technical hinge and tighten slightly the screws.
3) Remove the bottom hinge, install the support of the bottom technical hinge.
4) Fit the bottom technical hinge on its support and tighten slightly the screws.
5) Fit the technical door on the technical hinges.
6) Adjust the door (see inset).
7) Tighten the screw of the hinges.
8) Remove the door lock plate.
Bottom Technical
Hinge Support
Top Technical
Hinge Support
Door adjustment:
level the cellar, align the
hinge chest side with the
hinge door side, adjust the
door in order to obtain a
gap of 14 mm between the
inner frame of the door
and the frame of the chest.
Check using a sheet of
paper if the seal is airtight
on all it tower of the cellar
when the door is closed.
TopTechnical
Hinge Support
TECHNICAL DOOR ASSEMBLY

TECHNICAL DOOR ASSEMBLY
www.eurocave.co.uk
email:[email protected]
57 Chiltern Street London W1U 6ND
Phone:[phone]

60mm
25mm
84mm
60mm
25mm
592mm
Ref:059
726mm
Ref:259
1709mm
Ref:059
676mm
Ref:259
1659mm
Mounting clamp
Clamp holes Hinge
TECHNICAL DOOR ASSEMBLY
Wine cabinet
Technical door
Fitted door
www.eurocave.co.uk
email:[email protected]
57 Chiltern Street London W1U 6ND
Phone:[phone]