EV LIGHT EV 3108 User manual

USER MANUAL
Please read it carefully
EV 3108
13211072211
01010107210
7par3108
EV LIGHT
Ａｐｐｅａｒａｎｃｅ ｐａｔｅｎｔ Ｎｏ．： ２０１３３０００８８８２．２
R

INDEX
1、 SAFETY GUIDELINE··················································································· - 2 -
2、 TECHNICAL PARAMETER ·········································································· - 3 -
3、 LIGHTING INSTALLATION ·········································································· - 4 -
4、 POWER SUPPLY-CONTROL SIGNAL CONNECTIONS ···································· - 4 -
5、 OPERATION MENU··················································································· - 5 -
5.1 BUTTON OPERATION ··················································································· - 7-
5.2 DMX ADDRESS CODE SETTING····································································· - 7-
5.3 STATIC SETTING···························································································· - 7-
5.4 COLOR CAST CALIBRATION SETTING···························································· - 7-
5.5 CHANNEL MODE SETTING ··········································································· - 7-
5.6 DIMMING MODE SETTING··········································································· - 7-
5.7 DISPLAY SETTING ························································································· - 7-
5.8 RUN THE AUTO-RUN, AUTO-PROGRAMMING PROGRAM··························· - 7-
5.9 EDIT AUTO-PROGRAMMING PROGRAM······················································ - 8-
5.10 CHECK THE LIGHTING INFORMATION ······················································· - 8-
5.11 LIGHTING SETTING PARAMETER RESET ···················································· - 8-
5.12 【PROG】AUTO-PROGRAMMING PARAMETER RESET ······························· - 8-
5.13 LIGHTING RESET························································································ - 8-
5.14 LIGHTING PARAMETER DOWNLOADING EACH OTHER ····························· - 8-
6、 MAINTENANCE ························································································ - 9 -
7、 TROUBLESHOOTING················································································· - 9 -
8、 DMX PROTOCOL ···················································································· - 10 -
These items are packed together with the lighng ，please check：
Name Quanty Unit Remark
This manual 1 Pc
Safety cord 2 Pc
The power cord 1 Pc
Signal line 1 Pc
ACCESSORIES
Hanging device 2 Set

１、SAFETY GUIDELINE
Please keep this manual in a safe place for further reference. Please make sure
they also have this user manual if you sell this lighting to other users. Every unit
is packed properly by the manufacturer. Please operate this lighting according to
the user manual. Any damage caused by improper use will not be assumed by the
manufacturer.
Whenreceiving the lighng ，please dispose the carton, check and inspect there is any
damage or not. Should there be any damage caused by transportaon，do not use the lighng
and consult your dealer or the manufacturer.
This lighng canbe used indoors and outdoors, IP65.
The lighng is only intended for installaonand operaonby qualified personnel.
Do not mount the lighng directly onto inflammable surface.
Ensure power supply voltage correspond to device requirements before running.
It is essenal that each lighng is correctly earthed and that electrical installaonconforms
to all relevant standards.
Whenthe lighng is hanged to a high place, please use a safety cord provided to pass
through the lighng handles as a secondary safety fixing for safety seasons. For details, refer to
“LIGHTING INSTALLATION” secon.
Avoid direct exposure to the light from the lamp（specially for people with epilepsy）. The light
is harmful to eyes.
Do not project the beam onto inflammable surfaces. The minimum distance betweenthe
lighng and irradiated object should be 2 m.
Exterior surface temperature of the lighng will be 65℃whenworking，please do not touch
it with bare hands .
To prevent electric shocking, please do not touch the power cord whenthe lighng is
running.
Never let the power cord mix with other cables.
The LED lens should be changed if deeply scratched or cracked.
There is no user serviceable parts inside the lighng. Before using the device, please check
whether the covers or housing are well installed or not, and whether the screws are installed firmly
or not. Do not openthe housing and never operate the lighng with the covers removed.
Always disconnect a lighting from the power supply when the device is not in use or
before cleaning it or before attempting any maintenance work!
Electrical conneconmust only be carried out by qualified personnel.
Please use the original packing material for second transportation.
If you have any questions or suggestions, please do not hesitate to consult your
dealer or our factory.

-2-

２、TECHNICAL PARAMETER
Input Voltage：AC100V-AC240V，50/60HZ；
Power Consumpon：324W ;
Lamp Specificaons：108 pcs(27R+27G+27B+27W)3W LED,rate life 50000 hours.
Lens Angle：15º（Optional:25º,45º)
Spot Angle：28º；
Color：RGBW linear color mixing；
Color Temperature：color cast calibraonseng、color temperature output inside device；
Dimmer：0-100% linearly dimming，5 types dimmer modes，smooth dimming, flicker-free；
Shuer：independent electronic strobe；
Control Mode：
Standard DMX512，3 pininterfaces；
4 channel modes；
Master/slave mode，no need to set up the master and slave manually, will receive the main
engine data automacally;
5 auto-running modes，rainbow channel and rainbow effect；
Other Funcons：
Self-programming funcon, 5 chases，each chase has 20 scenes，fade funcon;
Lighng seng data、self-programming data canbe downloaded each other;
Temperature Control Protecon：both of lamp holder and base have temperature control
protecon;
Waterproof Grade：IP65；
Work Environment Temperature：-20°C～40°C；
Net Weight：23Kg；
DIMENSION
-3-

3、 LIGHTING INSTALLATION
The lighng canbe hanged at the high place with using the lamp hooks (as showed inpicture
one). Use the safety cord provided to pass through the handles and hang it as a second safety
fixing.
The lighting also can be used on the ground. If needed, using the bolt to fix
inthe mounng hole (as showed inpicture two) for fixing purpose.
Note:
Ensure support loading ability at least 10 times more than product weight，and
also make sure the lighting is installed steadily.
The lighting must be installed by the qualified personnel. Please install it
at the place where no one goes through.
4、 POWER SUPPLY-CONTROL SIGNAL CONNECTIONS
Make the XLR signal line connect with the lighng, one port connects with the output port of
lighng, another one connects with the input port of another lighng.
Due to the output and input of the lighng keep connecng all the me, so the DMX circuit
sll canbe keep connecng whenthe power of certainunit occurs turn-off.
XLR signal line only canbe used inseries conneconpaern(the amount of the lighng can
not be more than32 PCS), not available inparallel conneconpaern. Must add a signal
amplifier if the length of signal line exceeds 60M betweencontroller and lighng or between
two lighngs.
HOOK
SAFETY CORD
PICTURE ONE
PICTURE TWO
HANDLES
Inthe controller mode, at the last fixture inthe chain, the DMX output
has to be connected with a DMX terminator. The DMX terminator is
simply a connector with a resistor about 120Ω（OHM）connected
across pins 2 and 3 of the Canon plug（please see the picture
in the right）.It canprevent the noise and refleconcaused by DMX
512 signal during transmission.
MOUNTING HOLE FOR BOLT
-4-
MOUNTING HOLE FOR LAMP HOOK
LAMP HOOK

The transmissionspeed of DMX 512 signal is very quick. It will affect the signal transmissionif
any damage of the signal line, the weld is not firm or bad conneconetc
The connector with 3 pins XLR is more universal thanthe one with 5 pins XLR.
3 pins XLR：PIN 1：GND，PIN 2：- signal，PIN 3：+ signal.
5 pins XLR：PIN 1：GND，PIN 2：- signal，PIN 3：+ signal，PIN4/PIN5：UNUSED.
There can’t be more than12 PCS of lighngs for series conneconpaernwhenusing 220V
AC; it can’t exceed 6PCS lighngs for series conneconpaernwhenusing 110V AC.
5、 OPERATION MENU
Tab Level 1 Level 2 Level 3 Level 4
ADDR
(Address)001-512
STAT
(Static control)
R (RED)0-255 *
G (GREEN)0-255 *
B (BLUE)0-255 *
W (WHITE)0-255 *
SHUT 0-255 *
SET
(Set)
CAL
(Calibration)
R (RED)0-255
G (GREEN）0-255
B (BLUE)0-255
W (WHITE)0-255
USE YES/NO
CHMD
(Channel mode)
10CH
7CH
5CH
4CH
DIM
(Dimming mode)
OFF
DIM1
DIM2
DIM3
DIM4
DISY
(Display set)
ON
(Permanent on)
2MIN
(2 minutes off)
CTST
(Color temperature set)
CT01
R (RED)0-255
G (GREEN)0-255
B (BLUE)0-255
W (WHITE)0-255
……
CT10
AUTO
(Auto) AT01 RUN.. *
-5-
power in
DMX in to terminator
power out
ＤＭＸ ｏｕｔ

……
AT05 RUN.. *
ATSP
(Auto speed)0-255(second)
CHS1 RUN.. *
……
CHS5 RUN.. *
CHS1
（Chase 1）
SC01
（Scene 1）
R (RED)0-255
G (GREEN)0-255
PROG
（Program）
B (BLUE)0-255
W (WHITE)0-255
SHUT 0-255
TIME 0-255(second)
WAIT 0-25.5(second)
USE YES/NO
……
SC20
（Scene 20）
……
CHS5
（Chase 5）
SOFT
(Software version Vx.x
LEDs
xxR
INFO
（Information）
xxG
xxB
xxW
POW
(Power reduction)100%/80%/50%
LOAD
(Load)
ST L
（Setting load）YES/NO
PR L
（Program load）YES/NO
REST
(Reset)YES/NO
SEND
(Send)YES/NO
-6-
Illustrations：
When the menu is set as the information of * position, the
projector will be set automatically to be the main engine and then
send data to external. Other projectors can receive these data and run
synchronously with the main engine. It still be run according to these
setting parameter even if power reconnection after power off .
When setting YES in【ST L】menu, The parameter will bereset to be
the factory default value as which with underline of above chart.

-7-
5.1 BUTTON OPERATION
1) MENU：To returnto the previous menu.
2) ENTER：Enter to the next menu or save.
3) UP：Menu seleconor increasing the parameter.
4) DOWN：Menu seleconor decreasing the parameter.
5.2 DMX ADDRESS CODE SETTING
1) Press the 【ENTER】buonin【ADDR】menu, thenenter to the DMX address code seng.
2) Press the【UP/DOWN】buonto select【1-512】numerical value.
3) Press the【ENTER】buonto escape and save.
5.3 STATIC SETTING
1) Press the【ENTER】buonin【STAT】menu, thenenter to the stac seng.
2) Press the【UP/DOWN】buonto select 【RED】，【GREEN】，【BLUE】，【WHITE】and【SHUT】.
3) Press the【UP/DOWN】buonto set up the【0-255】numerical value.
4) Press the【ENTER】buonto escape and save.
5.4 COLOR CAST CALIBRATION SETTING
1) Press the【ENTER】buonin【CAL】menu, thenenter to the color cast calibraonseng.
2) Press the【UP/DOWN】buonto select 【RED】，【GREEN】，【BLUE】，【WHITE】
3) Press the【UP/DOWN】buonto set up the【0-255】numerical value.
4) Onthe【USE】interface, pressing【ON】buonmeans valid, otherwise【OFF】buoninvalid.
5) Press the【ENTER】buonto escape and save.
5.5 CHANNEL MODE SETTING
1) Press the【ENTER】buonin【CHMD】menu, thenenter to the channel mode seng.
2) Press the【UP/DOWN】buonto select【10CH】，【7CH】，【5CH】，【4CH】
3) Press the【ENTER】buonto escape and save.
5.6 DIMMING MODE SETTING
1) Press the【ENTER】buonin【DIM】menu, thenenter to the dimming mode seng.
2) Press the【UP/DOWN】buonto select【OFF】，【DIM1】，【DIM2】，【DIM3】and【DIM4】
3) Press the【ENTER】buonto escape and save.
5.7 DISPLAY SETTING
1) Press the【ENTER】buonin【DISY】menu, thenenter to the display seng.
2) Press the【UP/DOWN】buonto select【ON】，【2 MINITES OFF】
3) Press the【ENTER】buonto escape and save.
5.8 RUN THE AUTO-RUN, AUTO-PROGRAMMING PROGRAM
Illustrations: When pressing the【ON】button which means valid on the【USE】
interface, the actual output value of RED，GREEN，BLUE，WHITE is output in
accordance with the percentage which the color cast calibration value divides 255.
Illustrations：When setting【OFF】 in【DIM】menu, there will be no delay dimming
effect. The dimming speed of DIM1-DIM4 is from fast to slow. It will be set【OFF
】automatically in【DIM】menu when showing the shutter effect.
1)Press the【ENTER】button in【AUTO】menu, then enter to the running the auto-run,
auto-programming program.

-8-
5.9 EDIT AUTO-PROGRAMMING PROGRAM
1) Press the【ENTER】buonin【PROGRAM】menu, thenenter to the eding auto-programming
program.
2) Press the【UP/DOWN】buonto select【CHASE01】…【CHASE05】
3) Press the【ENTER】buonfor confirmaonand enter to the next menu.
4) Press the【UP/DOWN】buonto select【SCENE01】…【SCENE20】
5) Press the【ENTER】buonfor confirmaonand enter to the next menu.
6) Thenpress the【UP/DOWN】buonto select【RED】，【GREEN】，【BLUE】，【WHITE】，【SHUT】，
【TIME】，【WAIT】，【USE】
7) Press the【UP/DOWN】buonto set up the parameter which are needed.
8) Press the【ENTER】buonto escape and save.
5.10 CHECK THE LIGHTING INFORMATION
1) Press the【ENTER】buonin【INFO】menu, thenenter to the checking
the lighng informaon.
2) 【SOFT】buonis for soware versioninformaon.
3) 【LEDs】buonis for the LED quanty informaon.
4)【POW】buonis for the current informaonof power reducon. It is 100% output innormal
condions, but 80% or 50% output inover temperature proteconsituaon.
5.11 LIGHTING SETTING PARAMETER RESET
1) Press the【ENTER】buonin【ST L】menu, thenenter to the lighng seng parameter reset.
2) Press the【UP/DOWN】buonto select【YES】.
3) Press the【ENTER】buonto escape and save.
5.12 【PROG】AUTO-PROGRAMMING PARAMETER RESET
1) Press the【ENTER】buonin【PR L】menu, thenenter to the【PROG】auto-programming
parameter reset.
2) Press the【UP/DOWN】buonto select【YES】.
3) Press the【ENTER】buonto escape and save.
5.13 LIGHTING RESET
1) Press the【ENTER】buonin【REST】menu, thenenter to the lighng reset.
2) Press the【UP/DOWN】buonto select【YES】.
3) Press the【ENTER】buonfor confirmaonof lighng reset.
5.14 LIGHTING PARAMETER DOWNLOADING EACH OTHER
1) Press the【ENTER】buonin【SEND】menu, thenenter to sending parameter to other lighngs.
2) Press the【UP/DOWN】buonto select【YES】.
3) Press the【ENTER】buonto confirm sending.
Illustrations：When【USE】 is set to be【NO】，or the
parameter of【TIME】 is 0, it will not run this scene.
When 【WAIT】is set to be FADE time, the running process
isas the right chart showing.
2)Press the【UP/DOWN】button to select【AT01】…【AT05】，【SPEED】，【CHASE01】
…【CHASE05】
3)Press the【ENTER】button to start running.

6、 MAINTENANCE
7、 TROUBLESHOOTING
PROBLEM REASON AND ACTION
The lighng can’t be
started normally
Check the power conneconis correct or not.
Please detect the voltage.
Power supply is damaged or incorrect connected. Call a qualified
personnel to fix it.
Conneconof control board is not correct. Call a qualified personnel
to fix it.
Out of console’s
control
Please check the DMX connector and the power conneconis
connected correctly or not. It means having signal if it shows twinkling
of the decimal point which inthe lower right corner of the screen
whenexing the screensaver.
Please check the DMX address seng of lighng is correct or not.
Check【CHMD】seng is correct or not.
Please check whether the DMX line is near to the high voltage wire or
not. Inthat case, it will damage or interfere the DMX electric circuit.
The beam appears
dim ,the brightness
declines obviously
Check whether the 【CAL】is started or not and the set value is too
small.
Check whether the【POW】is inover temperature proteconsituaon
or not, if yes, please take measures for venlaon.
-9-
To prolong the life of lighting, it is very important to do the maintenance
work. The environment is hash outdoors, or if the lighting is idle for a long
time, damp, dust can cause greater accumulation of dirt on its cover or
housing. So it should be cleaned to maintain an optimum light output and at
the same time to prevent it from corrupted by dust and acid gas.
Cleaning frequency depends on the lighting operation frequency and the
environment in which the fixture operates. Soft cloth and typical glass
cleaning products should be used for cleaning. It is recommended to clean
projector at least once every 20 days.
Do not use any organic solvent,e.g.alcohol, to clean housing of the apparatus.
Illustrations：
1)Must disconnect the connection of projector and console before sending the parameter.
2)The information of【ADDR】、【CAL】can’t be sent, can’t be downloaded each other.
3)There will be an automatic reset of the other projectors after receiving parameter
correctly.

8、DMX PROTOCOL
-10-
4CHS 5CHS 7CHS 10CHS Value Function
- CH1 CH1 CH1 0—255 Dimming all
CH1 CH2 CH2 CH2 0—255 Red
CH2 CH3 CH3 CH3 0—255 Green
CH3 CH4 CH4 CH4 0—255 Blue
CH4 CH5 CH5 CH5 0—255 White
0—10 No strobe
11—90 Strobe，slow->fast
91—170 Random Strobe，slow->fast
171—255 Electronic Squarewave，slow->fast
0—10 No effect
11—20 WHITE 1:3200K
21—30 WHITE 2:3400K
31—40 WHITE 3:4200K
41—50 WHITE 4:4900K
51—60 WHITE 5:5600K
61—70 WHITE 6:5900K
71—80 WHITE 7:6500K
81—90 WHITE 8:7200K
91—100 WHITE 9:8000K
101—110 WHITE 10:8500K
111—120 AT01:R,G,B,RG,RB,GB
121—130 AT02:R↑,R↓,G↑,G↓,B↑,B↓,W↑,W↓
131—140 AT03:R↑G↑,R↓G↓,R↑B↑,R↓B↓,B↑G↑,B↓G↓
141—150 AT04:R↑G↑B↑W↑,R↓G↓B↓W↓
151—160 AT05:(Rainbow effect)B,BG↑,BG,B↓G,G,GR↑,GR,G↓R,R,RB
↑,RB,R↓B
161—170 CHASE1
171—180 CHASE2
181—190 CHASE3
191—200 CHASE4
201—210 CHASE5
211—255 Reserved
- - - CH8 0—255 0-255(S)speed of auto-run（fast->slow，when AUTO1 - AUTO5
effective）
Virtual colour wheel
0—10 No effect
11 Blue (Blue=full, Red+Green+White=0)(step)
12—50 Red=0, Green->up,Blue =full, White=0(proportional)
51 Light Blue (Red=0, Green=full, Blue =full, White=0)(step)
52—90 Red=0, Green=full, Blue->down, White=0(proportional)
91 Green (Red=0, Green=full, Blue =0, White=0)(step)
92—130 Red->up, Green=full, Blue=0, White=0(proportional)
131 Yellow (Red=full, Green=full, Blue=0, White=0)(step)
132—170 Red=full, Green->down, Blue=0, White=0(proportional)
171 Red(Red=full, Green=0, Blue=0, White=0)(step)
172—210 Red=full, Green=0, Blue->up, White=0(proportional)
211 Magenta (Red=full, Green=0, Blue=full, White=0)(step)
212—250 Red -> down, Green=0, Blue=full, White=0(proportional)
251—255 Blue (Red=0, Green=0, Blue=full, White=0)(step)
0—10 Use the dimmer mode which menu has set up
11—20 Dimmer off
21—30 Dimmer 1
31—40 Dimmer 2
41—50 Dimmer 3
51—60 Dimmer 4
61—254 Use the dimmer mode which menu has set up
255 Reset（at least 5S）
-
-
-
-
-
-
-
-
CH7 (CH7
Prior to
CH9)
CH10
CH9
CH6
-
-
CH7
CH6

EV LIGHT(GUANGZHOU) CO.,LTD.
ADD:ＥＶ ＩＮＤＵＳＴＲＩＡＬ ＰＡＲＫ，８ ＣＨＵＡＮＧＹＥ ＲＯＡＤ， ＴＡＩＰＩＮＧ
ＤＥＶＥＬＯＰＭＥＮＴ ＺＯＮＥ， ＧＵＡＮＧＺＨＯＵ
TEL:[phone]
FAX:[phone]
WEBSITE: Ｈｔｔｐ：／／ｗｗｗ．ｅｖｌｉｇｈｔｐｒｏ．ｃｏｍ