Event Lighting M1B50W User manual

M1B50W
Beam Moving Head
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to
change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting
for any clarification or information regarding this item.
www.event-lighting.com.au
V1.0

2
www.event-lighting.com.au
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting
screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.
Product Installation
This device can be mounted in many orientations provided each
individual device is secured by the use of correct mounting bracket.
Use a safety chain when mounting this device overhead.

3
www.event-lighting.com.au
Product appearance, LUX chart, Dimensions
1. Project lens
2. Head
3. Arm
4. Base
5. Display
6. Foot stand
7. Operation button
8. Handle
9. Wireless indicator
10. Mic
11. Left button
12. Battery indicator
13. Up button
14. Down button
15. Enter button
16. Right button
17. Powercon in
18. Powercon out
19. Fuse
20. Power switch
21. 5-pin DMX in
22. 5-pin DMX out

4
www.event-lighting.com.au
Gobo wheel
Static gobo wheel

5
www.event-lighting.com.au
Position 1 Position 10
Position 2 Position 11
Position 3 Position 12
Position 4 Position 13
Position 5 Position 14
Position 6 Position 15
Position 7 Position 16
Position 8 Position 17
Position 9 Position 18

6
www.event-lighting.com.au
Menu operation
Description of icons in the menu
CONNECT LIGHT INFOMATION SET PROGRAM
Menu
Default setting shadowed. Mark with ①can be basic reloaded, ② be program reloaded, ③can be private reloaded.
Connect
DMX Address
① XXX DMX address setting
Wireless① Wireless Enabled
Light
Max
Temperature①
80~139℃80℃ /176~282℉176℉ Lamp off if temperature
continuously over for 2
minutes
Lamp Adjust① PAN…… Adjust value of channel
Information
Time Info. Current XXXX(Hours)
Fixture Life XXXX(Hours)
Fixture boot time
Fixture total run time
Temperature Near Lamp Temp (depends on fixture) Temperature Sensors
Fans Speed Near Lamp Fan (depends on fixture) Fan speed Sensors
Channel Value PAN…… Display value of channel
Error Message Pan,Tilt…… Error channels
Fixture Model xxxxxxxxxxxx Display model brand and
model
Software Ver 1U01 V1.0.00……… Version of each IC
Set
Reset All
Pan&Tilt
Colors
Gobos
Others
Reset all
Reset Pan&Tilt
Reset Colors
Reset Gobos
Reset Others
Movment Pan Reverse①
Tilt Reverse①
Pan Degree①
Encoders①
Pan/Tilt Mode①
ON/OFF
ON/OFF
630/540
ON/OFF
Stand/Smooth
Pan Reverse
Tilt Reverse
Choose Pan Degree
Encoder wheel on/off
Choose pan/tilt mode
UI Set Mic Sens. ③
No Signal①
Temperature. C/F①
Fans Mode①
Hibernation①
Backlight①
Flip Display①
0~99%,60%
Close/Hold/Auto/Music
Fahrenheit /Celsius
Auto Speed /High Speed
OFF, 01M~99M，15M
02~60m 02m
ON/OFF
Sensitivity of Mic
Mode when no signal
Temperature at ℃/℉
Fans mode
Sleeping mode
Show backlight time
Display 180°reverse

7
www.event-lighting.com.au
Display Bright③
Brand Show①
Key Lock①
Language③
00~31 10
ON/OFF
ON/OFF
En/简/繁/Fr/Sp
Display Brightness
Show brand or not
Key lock on/off
Language Select
Fixture Set Silent Mode ON/OFF Silent Mode
Frequency 600Hz---(1200Hz) Frequency
Users User Mode① Standard
Extended
Basic-8bit
Basic-16bit
User
Standard mode
Extended mode
Basic-8bit mode
Basic-16bit mode
User program mode
Edit User③ Max Channel = XX
PAN = CH01
:
Edit users mode
Calibration③ -Password-
Color
:
=XXX
=XXX
:
Password: 050
Calibrate channel value
Fixture ID③ Name
-Password-
PID Code
Name
Password: 050
Set PID of RDM
Wireless Set① DMX On Cable
Reset Connect
ON/OFF
ON/OFF
DMX Send Out
Reset Connect
Reload Default Basic Reload(①)
Program Reload(②)
---Password---
Private Reload(③)
All Reload
ON/OFF
ON/OFF
XXX
ON/OFF
ON/OFF
Basic Reload
Program Reload
Password: 050
Private Reload
All Reload
Program
Play① DMX Receive
Slave Receive
Sequence
Music
Slave Receive 1,2,3
Master / Alone
Master / Alone
DMX Receive
Choose slave position
Run Sequence
Music mode
Select Chase② Chase Part 1
Chase Part 2
Chase Part 3
Chase 1 ~ 8 Chase 1
Chase 1 ~ 8 Chase 2
Chase 1 ~ 8 Chase 3
Select and run auto program
Edit Chase② Chase 1
:
Chase 8
Chase Test
Step 01
Step 64
=SCxxx
=SCxxx
Test
Beginning scene
Ending scene
Edit Scenes② Edit Scene 001
~ Edit Scene 250
Pan,Tilt,……
--Fade
Time--
--Secne
Time--
DMX Input
=xxx
=xxx
=xxx
Input manual scene
Modify manually fading
time
Modify manually scene time
Input scene from exterior
controller
Scenes Record ScXX=>ScXX Auto Input scenes

8
www.event-lighting.com.au
DMX Chart
Channel Name Function Min
DMX
Max
DMX
St Ex Ba1 Ba2
1 1 1 1 Pan Pan Coarse 0 255
2 2 Pan fine Pan Fine 0 255
2 3 2 3 Tilt Tilt Coarse 0 255
4 4 Tilt fine Tilt Fine 0 255
3 5 3 5 Movement Speed fastest to Slowest 0 255
6
Movement
Function
Normal 0 15
Movement With Blackout 16 31
TBD 32 255
4 7 Shutter Function
Normal Shutter Functions 0 15
Pulse-effect Forward 16 31
Pulse-effect Reverse 32 47
Random Strobe 48 63
TBD 64 255
5 8 Shutter
Normal Shutter Functions
Close 0 31
Strobe Rate (slow to fast) 32 223
Open 224 255
Pulse-effect Forward
Close 0 31
Strobe Rate (slow to fast) 32 223
Open 224 255
Pulse-effect Reverse
Close 0 31
Strobe Rate (slow to fast) 32 223
Open 224 255
Random Strobe
Close 0 31
Strobe Rate (slow to fast) 32 223
Open 224 255
4 6 Shutter
Shutter closed 0 31
No function (shutter open) 32 63
Strobe effect slow to fast 64 95
No function (shutter open) 96 127
Pulse-effect in sequences 128 159
No function (shutter open) 160 191
Random strobe effect slow to fast 192 223
No function (shutter open) 224 255
6 9 5 7 Dimmer Dimmer (0->100%) 0 255
7 10 6 8 Virtual Color
Function
No Function 0 15
CTC Function 16 31

9
www.event-lighting.com.au
Forward Spin 32 47
Reverse Spin 48 63
Continuous 64 79
Color Bounce 80 111
TBD 112 255
8 11 7 9 Virtual Color1
CTC Function
Colour Temperature Correction
2000K->2700K 0 223
White 3200K 224 231
White 4200K 232 239
White 5600K 240 247
White 8000K 248 255
Forward Spin
Rainbow Effect (Slow->Fast) 0 255
Reverse Spin
Rainbow Effect (Slow->Fast) 0 255
Continuous & Color Bounce
Black 0 0
Red 1 1
Green 2 2
Blue 3 3
Red=full, Green=full, Blue=full 4 4
Red=0, Green->up, Blue=full 5 46
Red=0, Green=full, Blue->down 47 88
Red->up, Green=full, Blue=0 89 130
Red=full, Green->down, Blue=0 131 172
Red=full, Green=0,Blue->up 173 214
Red->down, Green=0,Blue=full 215 255
9 12 8 10
Virtual
Color2(Only On
Color Bounce)
Color Bounce
Black 0 0
Red 1 1
Green 2 2
Blue 3 3
Red=full, Green=full, Blue=full 4 4
Red=0, Green->up, Blue=full 5 46
Red=0, Green=full, Blue->down 47 88
Red->up, Green=full, Blue=0 89 130
Red=full, Green->down, Blue=0 131 172
Red=full, Green=0,Blue->up 173 214
Red->down, Green=0,Blue=full 215 255
10 13 9 11 Red-All Red 0->100% 0 255
11 14 10 12 Green-All Green 0->100% 0 255
12 15 11 13 Blue-All Blue 0->100% 0 255
13 16 Gobo Function Indexed 0 15

10
www.event-lighting.com.au
Indexed With Blackout 16 31
Forward Spin 32 47
Reverse Spin 48 63
Continuous 64 79
Shake 80 95
TBD 96 255
14 17 Gobo
Indexed & Indexed With Blackout & Shake
Position 1 (Open) 0 13
Position 2 14 27
Position 3 28 41
Position 4 42 55
Position 5 56 69
Position 6 70 83
Position 7 84 97
Position 8 98 111
Position 9 112 125
Position 10 126 139
Position 11 140 153
Position 12 154 167
Position 13 168 181
Position 14 182 195
Position 15 196 209
Position 16 210 223
Position 17 224 237
Position 18 238 255
Forward Wheel Spin
Stop to fastest 0 255
Reverse Wheel Spin
Stop to fastest 0 255
Continuous
Positioning from 0-360 degrees 0 255
12 14 Gobo
Indexed
Position 1 (Open) 0 1
Position 2 ~ Position 18 2 35
Indexed With Blackout
Position 1 (Open) 36 37
Position 2 ~ Position 18 38 71
Indexed With Shake
Position 2 72 80
Position 3 ~ Position 18 81 223
Forward Wheel Spin
Stop to fastest 224 239
Reverse Wheel Spin
Stop to fastest 240 255

11
www.event-lighting.com.au
15 18 13 15 Prism&
Prism Rot
Prism
Position 1 (Open) 0 3
Prism Rot Forward Spin
Slow to fastest 4 127
Prism Rot Stop 128 131
Prism Rot Reverse Spin
Slow to fastest 131 255
16 19 14 16 Focus Continuous
Focus In to Focus Out 0 255
17 20 Frost
Continuous
No Frost 0 127
Frost 0->100% 128 255
18 21 15 17 Control
Normal 0 7
Reset All 8 15
Pan & Tilt Reset 16 23
Color Reset 24 31
Gobo Reset 32 39
TBD 40 47
Other Reset 48 55
Display Off 56 63
Display On 64 71
TBD 72 79
TBD 80 87
Hibernation 88 95
TBD 96 255
- The device is controlled by universal DMX 512 protocol, DMX address is the start channel used to receive
instructions from the external controller. For independent control, each fixture must be assigned its unique address
control channels. For example, this device has four channel modes: 21/24/14/16, if we set the mode at standard 21
channels mode, and there are several models need to be independently controlled, we just simply address first
fixture at 1, and second fixture at 22, third one at 43, etc.
- If the devices have the same address, they will behave synchronically.
- Display is flashing when no DMX signal is received.
More functions
- RDM. RDM stands for “Remote Device Management”, with this function, users can realize remote control of the
device, such as remotely changing DMX address, reverse pan/tilt setting, check a lot of useful information such as
temperature, power consumption, fan speed. Etc. Every single device has a unique RDM code programmed at
manufacture to distinguish from each other. It is not recommended for users to change this code.
- Software upgrade function via DMX cable. If there is any new firmware for this device, it can be upgraded simply via

12
www.event-lighting.com.au
a software upgrade box, no need to change any mechanical parts. The upgrade box is not included in the package,
if need any further assistance please just contact your authorized dealer.
- Hibernation. The device will enter sleeping mode if activated after a period of disconnecting DMX signal to save the
power consumption, and will return immediately as soon as the DMX signal is sent again.
- Display back-up communication IC. There is a back-up communication IC installed in the display PCB, so users
could replace at once if the original one is broken.
- Display flips. By press up and down button for more than 3 seconds, the display will flip automatically, this function
is useful to read menu conveniently when device is hanged.
Technical Specifications
Power
- Input Voltage: 100~240V AC, 50/60 Hz
- Power Consumption: 106W
- Connection: Neutrik® PowerCON – In / Out
Photometric
- Light Source: 50W RGB LED Module
- Beam Angle: 2°
- Output: 1335 lumen, 161000 lux on @3M
- PWM: 1200Hz
- LED Lifespan: 50,000 hours
Effects
- Dimming: 0 ~ 100%
- Strobe: 0.5 ~26 Hz
- Focus: Linear via DMX
- Prism: 8 Facet & Frost
Movement 8 / 16 bit Auto Reposition
- Pan: 630°( 2.5 sec) or 540°( 2 sec)
- Tilt: 265° (1.8 sec)
Gobos
- Fixed: 1 x 17 + Open Fixed Gobo Wheel
Control
- Operational Modes: DMX, Auto Program, Sound Active, Master / Slave
- RDM: Change DMX Address, Display Flip, X/Y Reverse and so on
- Protocol: DMX512 (W-DMX™ Optional)
- DMX Channels: 18 / 21 / 15 / 17
- Interface: 5-Pin In / Out
- Display: 2.4″ Colour LCD Control Panel with Back-up Power.
- Software Upgrade via DMX: Yes

13
www.event-lighting.com.au
Housing
- Materials: ABS & Steel
- Finishing: Matte black
- Cooling: Multi Sensor Thermostat Controlled Variable Speed Fan
- IP rating: IP20
- Dimension: 299 x 437 x 398 mm
- Net Weight: 10kg
- Rigging: 2pcs Omega Brackets with 1/4-turn Quick Locks
MISC
- Road case: MCASE4SS
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au.