EverFocus EHD935F eZ.HD Series User manual

EHD935F eZ.HD Series
1080p Full High Definition
True Day/Night Outdoor IR Vandal Dome Camera
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: February 2016

2
Precautions
1. Do not install the camera near electric or magnetic fields. Install the camera away from
TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the
electromagnetic fields generated from these devices may distort the video image or
otherwise interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein. Improper disassembly or introduction of
corrosive materials may result in equipment failure or other damage.
3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may
cause permanent damage to the sensor and/or internal circuits, as well as creating
unbalanced illumination beyond the capability of the camera to compensate.
4. Keep the power cable away from water and other liquids and never touch the power cord
with wet hands. Touching a wet power cord with your hands or touching the power cord
with wet hands may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may
result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor
directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean
the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera
body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any
part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity or power source
ratings. This camera is suitable for indoor operation only. Use the camera at temperatures
within -40°C~50°C (-40°F~122°F) and humidity less than 80%; this device is not rated as
submersible. The input power source is 12VDC or 24VAC. Be sure to connect the proper + / -
polarity and voltage, as incorrect polarity or too high a voltage will likely cause the camera
to fail, and such damage is not covered by the warranty.
8. Mounting. Use care in selecting a solid mounting surface which will support the weight of
the camera plus any wind, snow, ice or other loading, and securely attach the camera to the
mounting surface using screws and anchors which will properly support the camera. If
necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional
support for the camera.

3
Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

4
Contents
1. Introduction...................................................................................................................... 5
1.1 Packing List .....................................................................................................................5
1.2 Features ..........................................................................................................................5
2. Cable Description.............................................................................................................. 6
3. Installation ....................................................................................................................... 7
3.1 Installation and Adjustment ...........................................................................................7
4. Configuration in the OSD Menu........................................................................................13
5. Specifications...................................................................................................................17

EHD935F eZ.HD Vandal Dome Camera
5
1. Introduction
The EverFocus eZ.HD Series EHD935F provides incredible performance in bright light or low light
environments, and the resolution listed in the specification from the actual camera you install. To
take full advantage of the amazing resolution available from this advanced imaging technology, the
EverFocus eZ.HD Series EHD935F uses a vari-focal lens together with 1/2.9" SONY 2.24M pixels
CMOS to deliver 1080p high resolution, 28 LEDs with range of 30m/100ft., together with a useable
native low light sensitivity of 0.08lux without using digital slow shutter. The camera truly provides
optimized images without compromising 1080p high resolution. The Digital Wide Dynamic Range
function provides clear color images in the most challenging of bright or unbalanced lighting
conditions. The true day/night IR enhances images in low light environments with guaranteed ZERO
ghosting. The EHD935F is equipped with a 3-axis rotation mechanical design that delivers wall or
ceiling mounting flexibility and an IP67 weather resistant, vandal proof dome housing. Users can
take the advantage of vari-focal 2.8~12mm DC iris lens to easily adjustable field of view from the
camera. The cameras also feature dual voltage operation and a full suite of OSD Menu and DSP
functions controllable at the camera (3DNR to save DVR HDD space, privacy masking, mirroring, and
much more). This is the camera that you have been waiting for to create analog CCTV systems that
produce astounding image clarity in a wide range of outdoor applications at the widest range of
light levels. The EHD935F supports both NTSC and PAL scanning systems, which can be switched via
OSD.
1.1 Packing List
1.2 Features
1080p full HD with high flexibility and performance for astounding image
1/2 . 9" SONY 2.24M pixels CMOS Sensor,delivering amazing high sensitivity
Vari-focal 2.8~12mm DC iris lens to captures the desired field of view
Extended IR range of up to 30M/100ft. with 28 LEDs (depending on scene IR reflectivity)
Camera Body x 1 Screw x 4
User Manual x 1 Screw Driver x 1
Test Lead x 1 Plastic Anchor x 4
Template Plate x 1 DC Power Pigtail Cable x 1
Adapter Plate x 1
Desiccant Bag x 1
Rubber Plate x 1
Hexagon Wrench x 1
Quick Installation Guide x 1
Warning Paper x 1

EHD935F eZ.HD Vandal Dome Camera
6
D-WDR to improve the visibility under high contrast scene
3D-Noise Reduction ensures less blurry moving subjects, vivid and high SN ratio images
even under low light environments
Weather resistant IP67 and built-in heater
Supports 1080p, 720p & 960H Analog signal output, which can be easily switched by OSD
The flexible angle viewing with its 3 Axis rotation design allows wall or ceiling mounting
eZ.Controller function: Control camera OSD settings and PTZ operation directly from DVR
end
2. Cable Description
No. Name Descriptions
1 Power Cable Connect to a 12VDC or 24VAC power source.
2 Video Output 1080p,720p and 960H output, using a 75 Ohm BNC-type
coaxial cable.
3 Test Lead Connect to a monitor for setting image aim and focus.
4 DC Power Pigtail Cable Optional power pigtail cable. The red wire is positive (+); while
the black wire is negative (-).

EHD935F eZ.HD Vandal Dome Camera
7
3. Installation
3.1 Installation and Adjustment
1. For Ceiling Mount / Wall Mount users: Stick the Template Plate on the position where you
want to attach the camera, drill four holes on the Template Plate for screwing the
Adapter Plate with the supplied Screws and Plastic Anchors.
If you wish to run the wires through the wall / ceiling, drill an additional hole in the
middle circle position.. Insert the supplied four Plastic Anchors into the holes.
2. Remove the Cover Cap, unscrew the four Set Screws using the supplied Hexagon Wrench.

EHD935F eZ.HD Vandal Dome Camera
8
3. Remove the Adapter Plate from the camera, and screw the Adapter Plate to the wall /
ceiling with supplied Screws, then put the camera back to the Adapter Plate.
4. If you want to wire the cable through the side of the camera, follow the steps below:
a. Remove the Circle Plate from the camera. You can simply loosen the Circle Plate using
a coin.
b. Run the cable through the Cable Conduit.

EHD935F eZ.HD Vandal Dome Camera
9
c. Use the supplied Rubber Plate to fix the cable and then tightly push the Rubber Plate
to the Cable Conduit tightly.
5. You can optionally mount the camera using an L-Shaped Mounting Bracket.

EHD935F eZ.HD Vandal Dome Camera
10
6. Connect the camera to an AHD DVR with the 12VDC or 24VAC power source using the
supplied DC Power Pigtail Cable or a power adapter.
7. Using the Test Lead for viewing the video image while adjusting camera angles. You can
also use the OSD Menu Joystick to configure camera settings.
a. Adjust camera angles by tilting or rotating the camera.
b. Configure the camera settings using the OSD Menu Joystick, connect one end of the
Test Lead to the Test-Out connector on the camera module and the other end to the
portable monitor.

EHD935F eZ.HD Vandal Dome Camera
11
Note: The function button is using to control direction, and also to switch video format and
video output. Please follow the detailed instruction as below to switch the camera to:
Switch between 1080p and 720p (Default, 1080p): Press Upward for 5 Seconds
Switch from HD (1080p / 720p) to 960H: Press Left for 5 Seconds
Switch from 960H to HD (1080p / 720p): Press Right for 5 Seconds
Switch between NTSC and PAL: Press Downward for 5 Seconds
8. Adjust the Zoom / Focus using the Zoom / Focus screws. Tighten the Zoom / Focus screws
using the supplied Screwdriver.
•Push the Joystick up / down to select
among menu items.
•Push the Joystick left/ right to adjust the
level of the selected item.
•Press the Joystick to enter the submenu
or exit the OSD Setup Menu.

EHD935F eZ.HD Vandal Dome Camera
12
9.Tear apart the outer packing( figure 1 ) to take out the Desiccant Bag ( figure 2 ), then make it
folded ( figure 3 ) and put it into the camera housing( figure 4 ).
Note: It’s recommended to close the cover cap immediately in case of reducing the
absorption capacity of the Desiccant Bag inside the camera.
10. Screw back the Cover Cap Set Screw using the supplied Hexagon Wrench.

EHD935F eZ.HD Vandal Dome Camera
13
4. Configuration in the OSD Menu
You can use the Joystick on the rear panel of the camera to configure camera settings in the OSD
menu. For details on the OSD menu structure as below:
No. Main Sub
Menu Sub Menu / Function
1 Lens DC Mode
Indoor
Outdoor
Min Shu. NTSC: 1/30
PA L : 1/2 5
Max. Shu.
NTSC: 1/60,FLK,1/240,
1/480,1/1000,
1/2000,1/5000,
1/10000, 1/50000
PAL: 1/50,FLK,1/200,
1/400,1/1000,
1/2000*,1/5000,
1/10000, 1/50000
Iris Speed 0 – 15
Manual
2 Exposure
Shutter
NTSC: 1/30, 1/60, FLK, 1/240, 1/480, 1/1000, 1/2000, 1/5000, 1/10000,
1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto
PAL: 1/25, 1/50, FLK, 1/200, 1/400, 1/1000, 1/2000, 1/5000, 1/10000,
1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto
AGC 0 – 15
Sens-up Off
Auto Sens-up X2, X4, X6, X8, X10, X15, X20, X25, X30
Brightne
ss 1-100
D-WDR
Off
On Level 0-8
Auto
Defog
Off
Auto
Pos/Size Position, Size,↑,↓,→,←
Gradation 0-2
Default
3 Backlight Off

EHD935F eZ.HD Vandal Dome Camera
14
BLC
Level Middle, High, Low
Area Position, Size,↑,↓,→,←
Default
HSBLC
Select Area1, Area2, Area3, Area4
Display Off
On Position, Size,↑,↓,→,←
Black Mask On/Off
Level 0-100
Model All Day
Night AGC Level 0-255
Default
4White
Balance
ATW
AWC→SET
Indoor
Outdoor
Manual Blue 1-500
Red 0-100
AWB
5
Day &
Night
Ext D→N(Delay) 0-60
N→D(Delay) 0-60
Auto
D→N(AGC) 1-255
D→N(Delay) 0-60
N→D(AGC) 1-255
N→D(Delay) 0-60
Color
B/W
Burst Off/On
IR Smart
Off
On
Level 0-15
Area Position, Size,↑,
↓,→,←
IR PWM Off
0-100
6 NR 2DNR Middle/Low/Off/High
3DNR Middle/Low/Off/High
7 Special Cam Title
Off
On 0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ▶→
←↑↓()ˉ-_▊/=&:~,.
D-effect Freeze Off/On

EHD935F eZ.HD Vandal Dome Camera
15
Mirror Off, Mirror, V-flip, Rotate
Neg. Image Off/On
Motion
Off
On
Select Area1,Area2,Area3,Area4
Display On Position, Size,↑,↓,→,←
Off
Sensitiv
ity 0-100
Color Green, Blue, White, Red
Trans 1.00,0.75,0.50,
0.25
Alarm
View Type Off, Block, Outline, All
OSD View On/Off
Alarm Out On/Off
Time 1-15
Default
Privacy
Off
On
Select Area1,Area2,Area3,Area4
Display
Off
Color Position, Size,↑,↓,→,←
Mosaic Position, Size,↑,↓,→,←
Inv Position, Size,↑,↓,→,←
Color White, Black, Red, Blue, CYAN, Yellow,
Green
Trans 1.00,0.75,0.50,
0.25
Default
Language ENG/CHN1/CHN2/GER/FRA/ITA/SPA/POL/RUS/POR/NED/TUR
Defect
Live DPC
Off
On AGC level 0-255
Level 0-100
White DPC
Off
On
Pos/Size Position, Size,↑,↓,→,←
Start Close the iris then press
DPC View Off/On
Level 0-60
AGC 0-14

EHD935F eZ.HD Vandal Dome Camera
16
Sens-up x2, x4, x6, x8,x10, x15, x20,
x25, x30
Black DPC
Off
On
Pos/Siz Position, Size,↑,↓,→,←
Start Press Enter
DPC View Off/On
Level 0-255
RS485
CAM ID 0-255
ID Display Off/On
Baud Rate 2400,4800,9600,19200 ,38400
8 Adjust
Sharpness
Off
Auto
Level 0-10
Start AGC 0-255
End AGC 0-255
Monitor
CRT Blue Gain 0-100
Red Gain 0-255
LCD
Gamma
User,0.45,0.50,0.55,0.60,0.6
5,0.70,0.75,0.80,0.85,0.90,
0.95,1.00
Blue Gain 0-100
Red Gain 0-100
LSC Off/On
Video. Out PAL/NTSC
9 AF
AF Mode
Semi.
Auto
Manual
One Shot AF
TDN AF On
Off
Lens Init.
10 Exit Save& END /Reset/Not Saved

EHD935F eZ.HD Vandal Dome Camera
17
5. Specifications
Specifications and designs are subject to change for improving the functionality of this product
without notice.
P/N
EHD935F
Pickup Device 1/2.9" SONY 2.24M pixels CMOS
Video Format
NTSC and PAL( can be switched via OSD)
Effective Pixels 1920 (H)*1080 (V)
Scanning System Progressive Scan
Sensitivity 0 lux with IR on
S/N Ratio Over48 dB (AGC OFF)
Electronic Shutter AUTO, Manual (X30~1/ 50000), FLK
Video Output BNC 1.0Vp-p 75Ω
Gamma Correction
0.45
Lens Type DC Iris 2.8-12mm, F1.4
BLC
OFF/BLC/HS BLC Selectable
AGC 0~15 Levels
White Balance
ATW/AWC-SET/INDOOR/OUTDOOR/MANUAL/AWB
Sync Mode Internal
Day/Night Ext, Auto, Color, B/W
UTC Function Supported
IR LED 28 Units
IR Distance Up to 30m/100ft. (depending on scene IR reflectivity)
OSD Languages 12-Language
DNR
2DNR/3DNR, Off
DEFOG Off/Auto
D-WDR
On/Off/Auto
Sens-up Off/Auto (x30~x2)
Mirror
Off, Mirror, V-flip, Rotate
Motion Detection On/Off for 4 selectable zones
Privacy Mask On/Off for 4 selectable zones
Environmental IP67 Weather Resistant
Power Source 12VDC/24VAC
Power Source 12VDC: 9w max./ 24VAC: 9.7w max.
Operating
Temperature
-40°C~50°C / -40°F~122°F
Humidity
Less than 80%
Dimensions 149 x 149 x 125mm / 5.86” x 5.86" x 4.92"
Weight
1500g/3.3lbs
Certifications CE/FCC/RoHS

EHD935F eZ.HD Vandal Dome Camera
EverFocus Electronics Corp.
EverFocus Taiwan:
12F-1, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Ta ipei City, Taiwan
TEL: [phone]
FAX: [phone]
www.everfocus.com.tw
[e-mail]
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: [phone]
FAX: [phone]
www.everfocus.de
[e-mail]
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: [phone]~39
FAX: [phone]
www.everfocus.com.cn
[e-mail]
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: [phone]
FAX: [phone]
www.everfocus.com.cn
[e-mail]
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010,
USA
TEL: [phone]
FAX: [phone]
www.everfocus.com
[e-mail]
EverFocus Japan:
3F Kuramochi, Buildingll 2-2-3 Koto-Bashi,
Sumida-Ku Tokyo, 130-0022, Japan
TEL: [phone]
FAX: [phone]
www.everfocus.co.jp
[e-mail]
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed
ofseparately from your household
waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit
qualitativ hochwertigen Materialien
und Komponenten, die recycelt und
wieder verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling
Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!