EverFocus EHD320 User manual

EHD32
0
1
1/ /3 3” ” C Co ol lo or r R Ru ug gg ge ed d D Do om me e C Ca am me er ra a
User’s Manual
and
Operation Instructions

Notice
This manual is presented to the users of EHD320 by EverFocus Electronics
Corp. With years of engineering researches, EverFocus has spared no effort
to provide the high quality products to the worldwide users. For the policy
of continual product improvement, EverFocus reserves the right to make
changes to the product specifications and documentation without notice.
All the components of the products, including accessories, components, and
outlook, are based on the agreements of each deals to satisfy all kinds of
users. Meanwhile, please be advised that every step of operation must
follow the instruction of this manual to keep EHD320 working under the best
condition. Please notice that EverFocus will not be charged any claims or
renewing cases resulted from inappropriate operation.

Table of Contents
S
afety Warning …………………………………………1
I
ntroduction……………………………………………..2
S
pecification…………………………………………….3
I
nstallation Instructions………………………….….…4
D
ip Switch Functions…………………………….….…9

Safet
y
Warnin
g
1. Do not install the camera near electric or magnetic fields.
Installed the camera away from TV, radio transmitter, magnet,
electric motor, transformer, audio speakers because the
magnetic fields generate from above devices will distort the
video image.
2. Do not install the camera in the high temperature environment.
Installed the camera away from stoves, or other heat
generating devices as the high temperature could cause
deformation, discoloration or other damages of the camera.
Install the camera at where the temperature range will stay
between -46℃to 50℃ (-50℉ to 122℉).
3. Never face the camera toward the sun.
Never aim the camera at the sun or other extremely bright objects
whether it is in use or not.
4. Cleaning
Do not touch the surface of CCD sensor by hand directly. Use
a soft cloth to remove the dirt from the camera body. Use lens
tissue or a cotton tipped applicator and ethanol to clean the
CCD sensor and the camera lens. When the camera is not in
use, put the cover cap on the lens mount.
5. Heater
Heater elements could be very hot!! Heaters are located inside
the camera housing and will active automatically while the
environment temperature is below 10℃. Do not touch the
heater element while it’s active.
1

Introduction
The most technically advanced EHD320 is the newest vandal-resistant Color
Rugged Dome Camera from EverFocus Electronics. The Color Rugged Dome
Camera can withstand a blow from a 10-pound sledgehammer and has a
built-in heater that allows for operation in low temperatures. It is perfect for all
high-profile crime-prone applications such as building entrances, retail stores,
and shopping malls. The extremely EHD320 is unquestionably one of the
world's toughest cameras and is your best choice for vandal resistance.
Main Features :
 Designed with advanced digital signal processing circuitry for high image
quality.
 The high sensitivity of 1.0 lux/F=1.2 is achieved by high –resolution 1/3”
interline transfer CCD.
 The electronic shutter and AGC allow the camera to be used in
environment with varying light levels.
 DC12V or AC24V switches automatically power supply; Line Lock for
AC24V.
 S/N Ratio reaches 48 dB or more.
 Both board lens and vari-focal lens (3.5~8mm or 9~22mm) are available.
 Compact size: 130mm x 130 mm x 98.9mm
 Polycarbonate base withstand the impact of a 10 pounds sledgehammer,
black color or clear as option.
 Aluminum die-casting base, white color
 Unique security screw locked
 Operating temperature –46 ~ 50 deg Celsius.
 Heater triggered when temperature less than 10 deg Celsius.
2

S
p
ecification
Pickupdevice: 1/3”interlinetransferCCD
Pictureelement: NTSC:768(H)×494(V)
PAL:752(H)×582(V)
Horizontal resolution: 480 TV lines
Sensitivity: 1.0 lux / F=1.2
S/Nratio: >48dB(AGCoff)
Weatherproof ratings: IP66
Electronic shutter: 1/60(1/50)~1/100,000(Board lens only)
IRISControl: Auto(vari-focallensonly)
Autowhitebalance: YES
Auto gain control: on/off switch
Backlightcomp: on/offswitch
LineLock: on/offswitchfor24VAC
Gammacorrection: 0.45
Video output: 1.0Vp-p,75ohm
Powersource: 12VDC+/-10%,
Heater ON 920mA,OFF 320mA
24VAC+/-10% ,Heater ON 920mA,OFF 290mA
PowerConsumption: 5WMax.
(12W when heater active; thermostatically controlled)
Sync.mode: InternalSync./Linelock(OnlyAC24V)
Dimension: 130mmx130mmx98.9mm
Lens: Boardlensf=3.6,F=2.0
Vari-focalF=3.5~8mm,F=1.6
Vari-focal F=9.0~22mm, F=2.0
Heater auto activated temperature: 10℃, Heater optional
Operating temperature: -46℃to 50℃
Weight: 1.7kg
3

Installation Instructions
1. Loosen the 4 fix screws on the housing cover by using the attached wrench
(Figure 1). Carefully uncap the housing cover as the direction shown below
(Figure 2), please pay attention not to damage the lens. To remove the
housing cover, push the hinges to the bottom of the bracket, the hinges can
be easily removed from the bracket.
Figure 2Figure 1
2. Remove the camera.
To remove the camera, first unplug the wire connection on the back of the
camera. Then loosen the 2 locking screws on the camera base, push the
camera base to the right (toward heater direction, as shown in Figure 3),
remove the camera from the mounting base. Reinstall the camera and the
cable while the base mounting is completed.
Figure 3
Vari-Focal Lens
Board Lens
Locking Screws
Heater
4

3. Mounting the base.
Attach the base to the wall or ceiling, fix the base by the 4 setscrews
attached in the accessory pack. The dome is weighted 1.7kg, please make
sure if the mounting is strengthened enough to support it, if not,
please reinforce the mounting according to the environment.
Note: The diameter of the screw hole isψ4.7mm.
Caution: To prevent moisture leaking into the housing, apply an
appropriate gasket or sealant around the conduit connection.
Side conduit entry
Figure 4
Mounting Setscrew
Mounting Setscrew
Back conduit entry Conduit plug setscrew
Mounting Setscrew
Mounting Setscrew
Back conduit entry (PF1/2)
Conduit plug
The camera comes with a conduit plug
p
re-installed in the PF 1/2 conduit entry
on the side. The screw can be removed
and installed in the back conduit entry.
Loosen the conduit plug setscrew (as
shown in Figure 5) before removing the
conduit plug.
Side conduit entry (PF1/2)
Figure 5
5

4. Re-assemble Camera
1. If mounting EHD320 on the wall, please to aim the “Wall” in line
with the triangle “S” marked on the lead frame. (factory default)
Figure 6-1
“Wall”
2. If mounting EHD320 on the ceiling, please to aim the “Ceiling” in
line with the triangle “S” marked on the lead frame.
Figure 6-2
“Ceiling”
6

5. Wire Connection
Connect the power supply cable (AC24V/DC12V), video output and alarm
output to the proper connectors shown as Figure 7.
The V. Phase adjustment screw is located on the termination board.
The vertical phase may require adjustment to synchronize the vertical
phase of the camera with other camera in the system when it is to be used
in the line-lock sync mode. Make the adjustment when the vertical phase
of the camera does not match with other cameras.
Termination Board
Micro Switch for Alarm trigger
Video
A
larm COM
V. PhaseAdjustment VR
GND
A
larm NO
A
larm NC
Power In
DC12V (+) or AC24V
Power In
AC12V (-) or AC24V
Figure 7
7