EverFocus H.265 VANGUARD II Series User manual

Value IP Series Network Camera
2MP, H265, IR & WDR
Quick Installation Guide
EHN1250-S
EBN1240-S
Copyright © EverFocus Electronics Corp.
Release Date: March, 2020
All the images including product pictures or screen shots in this document are for example only.
The images may vary depending on the product and software version. Information contained in
this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: [phone] FAX: [phone] www.everfocus.com.tw

1
1. Physical Description
1
2
EHN1250-S
EBN1240-S
SD Card Slot on
EHN1250-S
2
1
3
3
4
No.
Item Name
Descriptions
1
Light Sensor
Detects lights.
2
IR LEDs
IR LEDs for infrared illumination in night vision
applications.
3
Lens
Camera lens.
4
Micro SD Card Slot
Insert a micro SD card.
Dimensions
EHN1250-S
117.3mm / 4.62"
Ø 147mm / 5.79"
EBN1240-S
90mm / 3.54"
Ø 100mm / 3.94"

2
Packing List
Please check that there is no missing items in the package before installing.
EHN1250-S
EBN1240-S
1. Camera x 1
2. MAC Address Sticker x 2
3. Cable Gland Kit x 1
4. Screw x 4
5. Screw Anchor x 4
6. Desiccant Bag x 1
7. Torx Wrench x 1
8. Mounting Sticker x 1
9. Quick Installation Guide x 1
1. Camera x 1
2. MAC Address Sticker x 2
3. Cable Gland Kit x 1
4. Screw x 3
5. Screw Anchor x 3
6. Quick Installation Guide x 1
7. Mounting Sticker x 1
Note:
1. Equipment configurations and supplied accessories vary by country. Please
consult your local EverFocus office or agents for more information. Please
also keep the shipping carton for possible future use.
2. Contact the shipper if any items appear to have been damaged in the
shipping process.
Optional Accessory
You can go to the product page on EverFocus’website to check the related
optional accessories. www.everfocus.com.tw
2. Cables
The cables provide connections for network, power, audio input / output and
alarm input / output. A Reset Button Cable is also provided. Please be noted that
microphones / speakers with a (built-in) amplifier and external power supply are
required.
Note: To activate Audio function, the Audio function must be enabled. Please
refer to 5.5.2 Video Streaming in the User’s Manual.

3
EHN1250-S
Alarm Input / Output
LAN / PoE Cable
12VDC Power Input
Reset Button
Audio Output
Audio Input
EZN1240-S
LAN / PoE Cable
Power Cable (12VDC)
Alarm IO PIN Assignment
1
2
3
4
Alarm In
GND
COM
Alarm Out
Reset Button
The Reset Button can be used to restore the camera to factory default. When
the camera is powered up, press the Reset Button about 8 seconds to reboot the
camera.
3. Installation
3.1 EHN1250-S
1. Stick the supplied Mounting Sticker on the surface to mark the 4 screw
positions. Drill the 4 screw-depth holes on the surface and then push the
supplied 4 Screw Anchors into the screw holes. Optionally drill the bottom 2
Cable Holes if you want to run the cables through the surface.

4
+ +
+
+
+
+Screw Position x 4
Optionally drill the 2 Cable Holes if
you want to run the cables through
the surface.
2. Remove the camera cover by unscrewing the 3 cover screws using the
supplied Torx Wrench (Left Image). Screw the camera base to the surface
using the supplied 4 Screws (Right Image).
3. Optionally insert a micro SD card into the card slot (please refer to 1. Physical
Description).
4. Adjust the pan / tilt / rotate angles of the camera.
5. Connect the camera to power. You can either connect the camera to a 12VDC
power source or to a PoE switch using the PoE cable.
6. Connect the camera to the network using the supplied Cable Gland Kit.
a. Insert a RJ-45 network cable (without the RJ-45 connector on the one end)
through the supplied Waterproof Ring, Cable Gland, Stopper and Screw
Cap accordingly.
Waterproof Ring Cable Gland Stopper Screw Cap

5
b. Connect the RJ-45 cable to the LAN/PoE Cable of the camera.
RJ-45 Cable
LAN/PoE Cable
c. Tightly screw the Cable Gland and Screw Cap to the Rugged RJ-45
Connector Cable.
Screw Cap
Cable Gland
d. Crimp the RJ-45 connector onto the RJ-45 network cable. Note that the
wires should be placed into the RJ-45 connector based on the following
order (from left to right).
Orange with white stripe
Orange
Green with white stripe
Blue
Blue with white stripe
Green
Brown with white stripe
Brown
7. Before screwing back the camera cover, remove the 3 old desiccant bags from
the inside of Camera Cover and replace them with the supplied Desiccant Bag.
Screw the camera cover back to the camera.
Stick the supplied desiccant bag
Remove the 3 desiccant bags
Note: Please screw back the
Camera Cover immediately
in case of reducing the
absorption capacity of the
desiccant bag inside the
camera body.
8. Now you can access the camera live view. See 4. Accessing the Camera.
3.2 EBN1240-S
1. Stick the Mounting Sticker on the surface to mark the 3 screw positions. Drill
3 screw-depth holes on the surface and then push the supplied 3 Screw

6
Anchors into the holes. Optionally drill a Cable Hole on the center if you want
to run the cables through the surface.
Screw Position x 3
Optionally drill a Cable Hole if
you want to run the cables
through the surface.
2. Twist the Outer Housing counterclockwise and then remove the Outer
Housing.
Twist Outer Housing counterclockwise Remove the Outer Housing
3. Before screwing the Camera Base to the surface, thread the cables either
from the side-cut of the Camera Base or through the surface.
4. Screw the Camera Base to the surface using the supplied 3 Screws.
5. Place the camera body back to the Camera Base and twist back the Outer
Housing. Do not twist the Outer Housing too tight as you will have to adjust
camera angles while viewing camera live view.

7
6. Connect the camera to the network using the supplied Cable Gland Kit. Please
refer to 3.1.6
7. Connect the camera to power. You can either connect the camera to a 12VDC
power source or to a PoE switch using the PoE cable.
8. Access the camera live view. See 4. Accessing the Camera.
9. Adjust camera angles and then tightly twist back the Outer Housing.
4. Accessing the Camera
You can look up the IP address of the IP camera using the IP Utility (IPU)
program, which is included in the software CD.
The default IP mode of the IP camera is DHCP. However, if there is no dynamic IP
address assigned to the device, its IP will switch to 192.168.0.10
By default, the ID is admin and there is no password. Please input a password for
the first-time login.
5. Important Note for Motorized Lens Models
For motorized lens models (EHN1250-S), if you find the live
image out of focus, please try the instructions below:
1. Go to the Live page and open the Lens Control panel
(see image on the right).
2. Click the Restore button for the lens to restore to the
default position, and then click the Auto Focus button.
3. If the image is still out of focus, adjust the focus by
clicking the Focus “+”or “-“buttons.
P/N: 4605H125002001A
EZN1240-A EZN1240-A