EverFocus Value IP EZN1240-SG User manual

Value IP Series Network Camera
EZN1240-SG, EZN1540-SG & EZN2540-SG, H265, IR, WDR
Quick Installation Guide
EZN1240-SG / EZN1540-SG / EZN2540-SG
Copyright © EverFocus Electronics Corp.
Release Date: June, 2021
All the images including product pictures or screen shots in this document are for example only.
The images may vary depending on the product and software version. Information contained in
this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: [phone] FAX: [phone] www.everfocus.com.tw

1
1. Physical Description
1
3
4
EZN1240-SG / EZN1540-SG / EZN2540-SG
2
No.
Item Name
Descriptions
1Reset Button
/ Micro SD Card Slot
Use the supplied Hexagon Wrench to loosen the
screws to access the Reset Button and Micro SD
slot.
2 Sunshield Protect the camera from the direct fun rays.
3 Tilt Screw
Use the supplied Hexagon Wrench to loosen the
Tilt Screws.
4 Pan Screw
Use the supplied Hexagon Wrench to loosen the
Pan Screws.

2
Dimensions
EZN1240-SG / EZN1540-SG / EZN2540-SG
Packing List
Please check that there is no missing items in the package before installing.
EZN Series
1. Camera x 1
2. MAC Address Sticker x 2
3. Cable Gland Kit x 1
4. Screw x 3
5. Screw Anchor x 3
6. Hexagon Wrench x 2
7. Quick Installation Guide x 1
8. Installation Sticker x 1
Note:
1. Equipment configurations and supplied accessories vary by country. Please
consult your local EverFocus office or agents for more information. Please
also keep the shipping carton for possible future use.
2. Contact the shipper if any items appear to have been damaged in the
shipping process.
Optional Accessory
You can go to the product page on EverFocus’ website to check the related
optional accessories. www.everfocus.com.tw

3
2. Cables
The cables provide connections for network and power.
LAN / PoE Cable
Power Cable (12VDC)
Reset Button
The Reset Button can be used to restore the camera to factory default. When
the camera is powered up, press the Reset Button about 10 seconds to reboot
the camera.

4
3. Installation
3.1 EZN Series
1. Drill three holes on the surface according to the screw positions on the
Camera Base. Push the supplied 3 Screw Anchors into the holes. Drill another
hole in the middle within the 3 screw holes if you wish to run the wires into
the surface. Screw the camera to surface using the supplied 3 Screws.
Mounting Screws
Screw Anchors
2. Adjust the pan/tilt/rotate angles of the camera by loosen the Pan/Tilt/Rotate
screws using the supplied Hexagon Wrench.
Tilt Screw
Pan Screw
3. Connect the camera to power. You can either connect the camera to a 12VDC
power source or to a PoE switch using the PoE cable.
4. Connect the camera to the network using the supplied Cable Gland Kit.
a. Insert a RJ-45 network cable (without the RJ-45 connector on the one end)
through the supplied Waterproof Ring, Cable Gland, Stopper and Screw
Cap accordingly.
Waterproof Ring Cable Gland Stopper Screw Cap

5
b. Connect the RJ-45 cable to the LAN/PoE Cable of the camera.
RJ-45 Cable
LAN/PoE Cable
c. Tightly screw the Cable Gland and Screw Cap to the Rugged RJ-45
Connector Cable.
Screw Cap
Cable Gland
d. Crimp the RJ-45 connector onto the RJ-45 network cable. Note that the
wires should be placed into the RJ-45 connector based on the following
order (from left to right).
Orange with white stripe
Orange
Green with white stripe
Blue
Blue with white stripe
Green
Brown with white stripe
Brown
5. Optionally insert a Micro SD card into the card slot (please refer to No.1 in 1.
Physical Description).
6. Now you can access the camera live view. See 4. Accessing the Camera.
4. Accessing the Camera
You can look up the IP address of the IP camera using the IP Utility (IPU)
program from EverFocus website (key word search: "IP Utility").
The default network is DHCP. However, if there is no dynamic IP address
assigned to the device, its IP will switch to 192.168.0.10. By default, the ID is
admin and there is no password. Please input a password for the first-time login.