Everylite EZBeam Series User manual

BEFORE YOU BEGIN
Read these instructions completely and carefully.
RISK OF ELECTRICAL SHOCK
• Turn power off before inspection, installation or removal.
• Properly ground power supply.
RISK OF FIRE
• Use only UL approved wire for input/output connections
• Minimum wire size 18 AWG
• Follow all NEC and local codes.
Prepare Electrical Wiring
• Acceptable for use in dry, damp and wet locations
• Follow all National Electric Codes (NEC) and local codes.
Ϙc°³æßâÓòí³æ³ÌíÌíÓ³ÌæíÅÅÌæâý³ĄáòųĔϚųÌæÅíâ³³Ìϟ
ϘÌæòâßßųÅþ³â³æ³ÌæíÅÅíþÌâ³ýâϚĔăíòâϚÌÌĄÓÌíâÓÅæ³ÌíþÌϟ
• When choosing wire, factor in voltage drop, amperage rating, and type (in-wall rated, wet location rated, etc.).
.Ìáòíþ³â³ÌæíÅÅí³ÓÌÓòÅÓýâ°íþ³âæϚÌòæĔâϟ
• Do not install if product has any visible damage.
• Do not modify or disassemble this product beyond instructions or the warranty will be void.
STOP
!WARNING
Turn off power at the circuit breaker
before installing this product.
OFF
ON
OFF
ON
Shock Hazard.
May result in serious injury or death.
Install Guide
EZBeam Series
Date:
Type:
Firm Name:
Project:

www.everylite.com
Components
Pre-cut EZ Bar options
5
67
8
4
1
23
The EZ Bar comes standard in 2 ft, 3 ft, 4 ft and 5 ft options.
1- UL approved supply wire
2 - UL approved twist -on wire
connectors or In-line/IDC
connectors
3- Screws, rivets, electronic grade
silicone or equivalent
4- EZ Connector
5- 12 Volt Power Supply
6- LED Modules
7- EZ Bar
8 - L-Bracket
2
2’
3’
4’
5’
Connector Assembly
Utilizing the EZ Connector, standard lengths of EZ Bar can be mounted together to
create virtually any length without the need for cutting.
1936 Premier Row, Orlando, FL 32809 • Tel: [phone] Fax: [phone] • Toll Free: 1-888-567-4LED (4533)
Module Quantity per Run
In order to avoid any noticeable dimming between modules due to voltage drop, the amount of modules
in a single run must not exceed 7 modules* when power is supplied from one end only.
*This does not take into account the length or gague of cable being used. Onsite testing might be required
to avoid having a voltage drop greater than 12%.

3
12 3
Align L-Bracket on the cabinet wall, mounting
in place using screws. Adjust EZ Bar on the L-Bracket using the adjustment holes then screw in place once
appropriate spacing is acquired.
Pay attention to spacing between bars and
ensure that the bars are level before
permanently mounting in place.
X”
www.everylite.com
1”
2”
4’ + 2’ = 6’
5’ + 2’ = 7’
5’ + 4’ = 9’
5’ + 3’ = 8’
5’ + 5’ = 10’
5’ + 4’+ 2‘ = 11’
Bar assembly options
New Application Mounting
Connecting power supply
Screw cap wire connector
Negative -
Positive +
AC Power
50/60Hz
3
1936 Premier Row, Orlando, FL 32809 • Tel: [phone] Fax: [phone] • Toll Free: 1-888-567-4LED (4533)

12V
Input
Output
AC Power
50/60Hz
c°ªÓÅÅÓþ³Ì«³«âË³æßâÓý³æÌăËßÅæĄæíË泫ÌϟÅþĄæâý³þ°ÓËßÓÌÌí³ÌæíÅÅí³ÓÌ«ò³ªÓâí³ÅÌ
up-to-date wiring instructions. Install in accordance with NEC and local regulations.
www.everylite.com
Wiring Diagram
See ‘System Diagram’. Ensure the system is wired correctly and polarities are correct.
Ensure a compatible power supply is installed.
Ensure driver is not overloaded. An overloaded driver will cause the internal auto-reset to trip repeatedly.
ÌæòâĔăíòâ°æÌÓíÌÌíăææ³ýÅĄϚòæ³Ì«ÓËßÓÌÌíæÌæÓÅâíÓí°ªâÓË³âò³íÓâϟ
ÌæòâÌÓ³ËËâ³æ³ÌæíÅÅϟ.ªų«°íæÓÌí³ÌòíÓĕ³ÂâϚ°ÂªÓâÅÓÓæÓÌÌí³ÓÌæϟ
LEDs does not illuminate
LEDs is slowly flashing
Some LEDs are not functional
Lights are flickering
Troubleshooting
Tel: [phone] Fax: [phone] Toll Free: 1-888-567-4LED (4533)
Monday through Friday, 8:30am - 5:30pm ET. 1936 Premier Row, Orlando, FL 32809
HAVE A QUESTION?
Visit www.everylite.com or contact Customer Support at