Evolio iFly Range User manual

Change the perspective!
User Manual

Main Features of the drone
Smooth and easy controllable flight behavior.
Simple construction, individual parts can be exchanged
quickly and easily.
Fun during flying is guaranteed because of 360° 3D-
flips.
Live image transmission via WiFi (App necessary).

Welcome to use our
●We reserve the final explanation right on this User’s Manual.
●This manual has been carefully checked. Please contact our service center at [email protected] , when
any typing mistake is found.
●Please read the operating instruction carefully and use the accessories only provided by the original
factory to avoid any unexpected damage. No warranty will be executed if you are not following the
instruction or connecting with the incompatible accessories, we assume no responsibility for any loss and
damage caused hereby.
1. Introduction
Dear Customer:
Thank you for buying this product. Please read this manual carefully to learn the ability of flying quickly and to
operate safety with this product. Please take care of the manual. We hope you will enjoy our new product.
IMPORTANT INFORMATION
Please note the valid standard for flying drones in your country!
The construction and operation of radio controlled models requires technical knowledge, craftsmanship and
safety-conscious behavior.
The drone is powerfull, when tacking off, move the throttle stick foreard gradually, to avoid it s rising too fast.
After the flight, torn off the drone first, then turn off the controller.
This product is not suitable for children under the age of 14. Children should be supervised by adults at all
times.
Fly only in safe areas and keep a reasonable safety distance to persons, animals and other objects.
The dealer and seller does not accept liability for any damage to property or injuries in case of non-observance
of the safety instructions.
1.1. Safety instructions
Fly only in safe areas away from other people or crowds. The operator is responsible for their actions,
damages or injuries occurred during the operation.
RC models are composed of many precision electrical and mechanical components. It is critical to keep the
model and associated equipment away from moisture and other contaminants. Do not operate or expose to
rain or moisture! Exposure to water or moisture may cause the model to malfunction resulting in loss of
responsiveness and could cause to crash.
Please keep people, animals or other objects away from the spinning blades of main rotors and tail rotors.
Please keep the model away from heat and strong sun exposure in order to avoid distortion or damage caused
by high temperature.
Please use this product only for its intended purpose.
Please store small parts in a place out of reach of small children to avoid choking hazard.
Please fly the drone according to your flight skills. Fatigue, illness and/or miss-operation will increase the
possibility of accidental hazard

If the product gets damaged, stop using it immediately.
Never throw any batteries into fire, risk of explosion!
If the blades need to be replaced, take care that they are assembled according to the correct direction of
rotation.
1.2.Battery Protection
The drone is powered by a Lithium-Polymer rechargeable battery (Li-Po). Li-Po batteries are different to
conventional batteries in that their chemical contents are encased in a relatively insubstantial foil packing. This has
the advantage of significantly reducing their weight, but does make them more susceptible to damage if roughly or
inappropriately handled. As with all batteries, there is a risk of fire or explosion if safety practices are ignored!
1. Do not charge Li-Po batteries near flammable materials or liquids.
2. Keep Li-Po batteries away from children or animals.
3. Never charge a Li-Po battery pack that has ballooned or swelled due to over-/undercharging or from crash.
4. Charge and store Li-Po batteries in a location where a battery fire or explosion will not endanger life or
property.
5. Never charge a Li-Po battery pack that has been damaged in a crash, discard it in accordance with your
country´s recycling laws.
6. Only charge your battery with the supplied charging cable and take care of the polarity.
7. If the Li-Po battery catches fire, never try to extinguish the fire with water. Use dry sand or a suitable fire
extinguisher.
8. Never overcharge a Li-Po battery and monitor charging batteries for signs of overheating.
9. Never leave a Li-Po battery unattended during charging.
10. Do not attempt to disassemble, modify or repair the battery.
11. Protect your battery during transportation or storage from damage.
12. To avoid that the battery gets deep discharged, charge the battery regularly when it is not in use. If the battery
voltage drops below 2V, the battery is defective and cannot be charged anymore. Dispose the battery
according to the applicable recycling laws of your country.
13. While not using the battery store it in a dry and dark area at a temperature between 18-25°C.
1.3.Maintenance
Clean the drone with clean, dry soft cloth only.
To avoid irreparable damage, keep the drone dry and away from water. Do not fly in rain condition.\
Check the drone and accessories for damage. If damage is found, do not use the drone until is repaired.
1.4.Symbols used on the product:
CE mark (Conformity Europe), this product is compliant
to designated European standards
Cells in the battery pack contain Lithium
The battery must not be disposed in the household waste.
Follow the instructions!
Li-Ion

1.5 Package content
Drone
Replacement rotor blades 4pcs.
USB charging and data cable
Li-Po battery 3,7V
Remote control
Manual
2. Battery Instalation & Charging
2.1.Installing the battery
1.Remove the battery cover.
2.Insert the 4x 1,5V AAA batteries according to the indicated polarity.
3.After the batteries are inserted, close the battery compartment.
Attention: Do not mix old and new batteries.
Do not mix different type of batteries.
Battery installation should be done under adult supervision only.
2.2 Charging the drone
3.Controller

4. Drone:
5. Connecting drone and remote control
Putt the throttle lever down
Turn on the controller
Oppen the battery frame and
insert the battery inside.Put the
battery plug into the drone for
connecting
Change of damaged or broken rotor
blades:
1. Loosen the screw on the rotor blade
2. Remove the rotor blade
3. Install the new rotor blade (Take care
of the letter on the rotor blade and the
drone. The letter must match to each
other, otherwise the drone doesn´t fly!)
4. Fix the rotor blade with the screw

Push the throttle up and down, a
beep will sound.The controller
connects to the drone. (The LED
light on the drone remains on). The
drone is ready to fly.
6.Operation and Control (MODE 2)
Turn on the drone (the LED
light on the drone flashes
rapidly)
Place the drone at a
level position

7. Trim Fine Tuning
Radical Flip& Rolls
You can perform flips with your drone in any of the speed settings. Press down the “MODE” button
once and then push the rudder in related direction.

Notice: Before you perform a Flip Trick, always make sure you have enough space both above and bellow your
drone.
8. Operation and Control (MODE 4)



1. Press the "SPEED" button to high speed (3 beeps).
2. Press the throttle and rudder down to 45 degree circle (as
above) for 10 second, you will see the light on the PC
board of drone flashing rapidly,then pls let go the throttle
and rudder, the light on the PC board remains on, the auto
trim finishes
Radical Flip& Rolls
You can perform flips with your drone in any of the speed settings. Press down the “MODE” button
once and then push the rudder in related direction.
Notice: Before you perform a Flip Trick, always make sure you have enough space both above and bellow your
drone.
9. Automatic trim function (Mode2/Mode4)
10. One-Key Return
When the drone is taking off, the LED light on the drone stop flashing, at the
moment, the drone sets its front side to be the front direction for one key

One-Key-Return
return flying.If you want to reset the front direction, then you need to turn off the rc drone and reset it again.
Press the Trim Slider A button down for one key back home function, and then control right sticker (Rudder) to every
direction to quit this function.
Headless Mode
HOW TO GET INTO/QUIT HEADLESS FUNCTION
FLYING?
Press the button on controller(as picture shows)for 3 seconds till beep
sound, you will get into compass mode flying.To quit from compass mode, just
press the same button for 3 seconds till beep sound disappears.
How to recognize the „Forward side“ under Headless
Function
When the drone is taking off, the LED light on the drone stop
flashing, at the moment, the drone sets its front side to be the
front direction for Headless Mode flying.
If you want to reset the front direction, then you need to turn off
the rc drone and reset it again.

11. Instruction for camera using
Pictures and Videos can be saved on a micro SD Card (not included), after putting it into the drone´s card slot.
1. Insert the TF card correctly into the camera.
2. Connect the camera to the drone by „CAM“
socket.
3.Hang the camera on the drone.
4. Before reviewing photos and videos, please
insert one end of DATA CABLE into the port of
camera correctly and the other end into computer.
Open “My Computer” and you will find related
file of photos and videos you took.
Extra instructions for wifi camera functions
1.Connect the stand bar to the mobile phone
fixing component.
2.Adjust the fixing component upward or
downward according to the size of the mobile
phone
3.Set the mobile phone holder to the top of the
remote control.
4.Use the screwdriver to tighten the bolt up

Install the camera on the drone
1. Plug the cable to “ WIFI” socket and to the wifi
camera.
2.Hang the camera on the drone.
12. Software download, installation and using
First you have to download the „Helicute FPV“ App in the Apple App Store or Google Play Store.
Alternatively, you can scan one of the two QR codes for your operating system with the smartphone.
IOS Android
13. Using instruction
Please proceed as follows:
1. Connect the model to the power, and the indicator on camera turns red.
2. Enter the „Setting“ menu of your mobile device, and turn on the wifi.
Notice:
If WiFi is already activated, your smartphone will not be able to find the drones network.
You must disable WiFi and enable then again to get connected.
3. After your Smartphone found the „HELICUTE FPV“ network, connect it with your phone.

4. Is the connection established, open the App and click play. The Live Image of the camera will be
transmitted.
14 Spare parts list
For customer assistance, please contact us at suport@evolio.ro.

Declaration of conformity
Televoice Grup S.R.L., with headqurtered in Bucharest, District 1, Grigore Cobalcescu no.39 RO15005294,
J40/11378/2002, declare on own responsability, this product Evolio iFly Range drone, solded in Romania :
Brand: Evolio;
Model: iFly Range
Commercial name: drone
The electric and electronics equipment solded by our company respect legal terms like: Decision no. 1022/2002,
H.G. 497/2003 (electromagnetical compatibility), H.G. 457/2003, modified by decision 1514/2003 (about consumer
safety with electric equipment ) and all normative acts, H.G. 992/2005 (about limited uses of dangerous substances),
H.G. 448/2005 about prevention of wastes electrical and electronic equipment) and UE Directives 2002/95/CE,
1999/5/EC.
The product was evaluated according with the following terms, mentioned in annex II a H.G. 88/2003: EN
62479:2010, EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011, EN 301 489-1, EN 301 489-17, EN 300 328.
All documents of the evaluations received from the manufacturer, are stored at our company headquarters. The all
products have inscription CE.
The products warranty are in conformity with O.G. 21/1992, Law 449/2003,Law 296/2004 and O.U.G 174/2008,
about consumer protect.
Liviu Nistoran

Table of contents
Other Evolio Drone manuals