Evolur aurora User manual

Read all instructions before
assembling and using product.
IMPORTANT - Keep Instructions
for future use. 0821R2-EV832
Owner’s Manual
AURORA
Convertible Crib
Scan the QR code to register your product
https://www.evolurbaby.com/customer-care/product-registration/

23
www.evolurbaby.com/help www.evolurbaby.com/help
SAFE SLEEP TIPS
…. for choosing Evolur and congratulations on joining our family;
a family that has been transforming lives for 30 years!
We appreciate your feedback and wish you the very best in the
coming years with your new addition. If you have any questions
or concerns please don’t hesitate to reach out to us. One of our
trusted Customer Care representatives will be happy to assist you.
Thank you again for entrusting us to supply you with safe,
and affordable baby products and accessories.
THANK YOU...!
LIMITED WARRANTY:
• Evolur warrants its product to be free from defects in material and
workmanship and agrees to remedy any such defect.
• This warranty covers 1 year from the date of original purchase.
• This warranty is valid only upon presentation of proof of purchase.
• This is solely limited to the repair or replacement of defective
furniture components and no assembly labor is included.
• This warranty does not apply to any product which has been
improperly assembled, subjected to misuse or abuse or which has
been altered or repaired in any way.
• This warranty gives you specific legal rights and you may also have
other rights which vary from State to State.
Adult Assembly
Required.
DO NOT use the
product if it is
damaged, broken,
and/or components are
missing or broken.
To protect your parts
during assembly
please place them on a
soft surface.
Contact Evolur Inc
In case of any
assistance needed.
Small parts may
present choking
hazard prior to
assembly.
Please read the
instructions
thoroughly. Identify all
parts & hardware.
Do Not Use Power
Drills or Drivers.
To clean surface, use
only water on a damp
cloth. Do not use
window cleaner or
cleaning abrasive as it
will scratch the
surface and could
damage the protective
coating.
For a Safe and
comfortable Sleep
experience, we
suggest using Evolur
Green Gaurd Gold
Snug Fit Full-Size
Mattress.
0-6

45
WARNINGS WARNINGS (cont.)
WARNING WARNING
Failure to follow these warnings and assembly instructions could result
in serious injury or death.
• To reduce the risk of sids, pediatricians recommend healthy infants be
placed on their backs to sleep, unless otherwise advised by your
physician.
• Check this product for damaged hardware, loose joints, missing parts
or sharp edges before and after assembly and frequently during use.
• DO NOT use this crib if any parts are missing, damaged or broken.
Contact évolur - 1532 s.Washington ave, Piscataway, NJ 08854 for
replacement parts.
• DO NOT use a water mattress with this crib.
• Read all instructions before assembling crib. Keep instructions for
future use.
• If refinishing, use a non-toxic finish specified for children’s products.
• Day-Bed Conversion : When converting the crib to day-bed, stabilizer
bar along with the guard rail manufactured by Evolur inc. must be
used.
• Toddler-Bed Conversion : When converting the crib to day-bed,
stabilizer bar along with the guard rail manufactured by Evolur inc.
must be used.
• Full-size Bed With Footboard Conversion : When converting the crib
to Full-Size Bed with Footboard, Full Size Bed Rail Manufactured by
Evolur Iinc, must be used.
STRANGULATION HAZARD:
• Strings cause strangulation! DO NOT place items with a string around
a child’s neck, such as hood strings or pacifier cords. Do not suspend
strings over a crib or attach strings to toys.
• To help prevent strangulation tighten all fasteners. A child can trap
parts of body or clothing on loose fasteners.
• DO NOT place crib near window where cords from blinds or drapes
may strangle a child.
• Infants can suffocate on soft bedding.
• Never add a pillow, comforter or padding.
• Never place additional padding under infant.
• Never use plastic shipping bags or any plastic film as mattress
covers, because they can cause suffocation.
• Infants can suffocate in gaps between crib sides and a mattress that
is too small. Any mattress used in this crib must be at least 27-1/4 in
(69 cm) by 51-5/8 in (131 cm), with a thickness not exceeding 6 in
(15cm) and a minimum thickness of 4 in (10 cm). The dimensions of
the mattress shall be taken from seam to seam or edge to edge
where appropriate.
FALL HAZARD:
• When child is able to pull to standing position, set mattress to lowest
position and remove bumper pads, large toys and other objects that
could serve as steps for climbing out. After raising side, make sure
latches are secure (disregard for non-drop side crib).
• DO NOT leave child in crib with sides lowered. Be sure side is in
raised and locked position whenever child is in crib (disregard for
non-drop side crib).
• Stop using crib when child begins to climb out or reaches the height
of 35 in (89 cm).
• When storing crib use caution as extreme changes in temperature or
humidity can compromise the crib making it extremely dangerous to
your child.
• Use caution when a vaporizer or humidifier is in use. Always aim
vapor away from the crib as well as any other wooden furniture.
Prolonged periods of humidity in storage as well as in the home can
compromise crib.
• Avoid using vaporizers and humidifiers for prolonged periods of time.
• Follow warnings on all products in crib.
• DO NOT use this crib if you cannot exactly follow the instructions.
www.evolurbaby.com/help www.evolurbaby.com/help

67
WARNING
WARNINGS (cont.)
• DO NOT use this crib for a child who can climb out of it or who is taller
than 90 cm.
• DO NOT place in or near this crib any cord, strap or similar item that
could become wrapped around a child’s neck.
• DO NOT place this crib neat a window or a patio door where the child
could reach the cord of a blind or curtain and be strangled.
• Ensure that the sides of this crib are properly latched or locked in
appropriate position where the child is left unattended in it.
• Check this crib regularly before using it and do not use it if any parts
are loose or missing or if there are any signs of damage. Do not
substitute parts. Contact the manufacturer if replacement parts or
additional instructions are needed.
• Use a crib mattress that is no thicker than 15 cm and is of such a size
that, when it is push firmly against any side of crib, it does not leave a
gap of more than 3 cm between the mattress and any part of the sides
of the crib.
• Children can suffocate on soft bedding. DO NOT place pillows,
comforters or soft mattress in this crib.
FOR TODDLER BED USE :
• Failure to follow these warnings and assembly instructions could result
in serious injury or death from entrapment orstrangulation.
• DO NOT place bed near windows where cords from blinds or drapes
may strangle achild.
• The mattress intended for use on this bed shall be a full-sizecrib
mattress having the dimensions of 51-5/8 in (1310 mm) in length and
27- 1/4 in (690 mm) in width and thickness of 4 in (100 mm) or greater
thickness as specified by manufacturer.
• The minimum age of the intended user shallnot be less than 15 months
and the maximum weight shall not be greater than 50 lbs. (22.7kg).
www.evolurbaby.com/help www.evolurbaby.com/help
Back Panel
1Right Panel
4
Front Panel
2Left Panel
3
Mattress Support
5Right Front Leg
7
8
Left Front Leg
6
Right Rear Leg
10
Left Rear Leg
9
PARTS
If there are any missing parts, please contact Evolur before using the
product.
Conversion Blocks
(Keep parts for Day
bed and Toddler Bed
Conversion)

89
www.evolurbaby.com/help www.evolurbaby.com/help
CRIB ASSEMBLY - FRONT LEGS ASSEMBLY
A
1
HARDWARE
If there are any missing parts, please contact Evolur before using the
product.
Screw 2-1/2” (×2)
AScrew 2-1/2” (×2)
BScrew 1-1/2” (×4)
Allen Key (×1)
Screw 1-1/2” (×6)
C
DScrew 5/8” (×4) EScrew 1-3/4” (×4)
EScrew 1-3/4” (×4)
GScrew 2-3/8” (×6) H
FScrew 2-3/4” (×2)
1a. Align the Left Front
Leg (6) towards the
left end of the Front
Panel (2). Similarly,
Align the Right
Front Leg (7)
towards the right
end of the Front
Panel (2).
1b. Insert the Screws
(A) at the lower hole
of both the Left and
Right Front Legs as
shown in the
diagram.
1c. Insert the Screws
(E) at the middle
and upper hole of
both the Left and
Right Front Legs as
depicted.
1d. Tighten the Screws
(A) and (E) using
the Allen Key (H)
provided.
(2)
(A)
(A)
(7)
(6)
(E)
(E)

3
CRIB ASSEMBLY – MATTRESS SUPPORT ASSEMBLY
10 11
www.evolurbaby.com/help www.evolurbaby.com/help
2
CRIB ASSEMBLY – SIDE PANEL ASSEMBLY
DScrew 5/8” (×4)
2a. To assemble the
Left Panel (3) and
Right Panel (4) of
the Crib, align
them to the Front
Panel (2) as
shown in figure.
2b. Insert the Screws
(B) inside the
holes provided at
the top and the
lower end.
2c. Tighten all the
four Screws (B)
using the Allen
key (H).
3a. Attach all the corners of
Mattress Support Panel
to the Front Panel (2),
Left Panel (3) and Right
Panel (4) as shown in
diagram.
3b. Insert the Screw (D)
and tighten it using the
Allen Key (H).
3c. Note that Lowest
position of the Mattress
Support Panel will be
for Toddler (babies who
can stand up and walk)
, Mid position is for
Infant babies who start
to turn and sit up) and
Highest Position is for
the New born.
3d. Ensure that the
Mattress Support Panel
is flat side up and not
slant.
BScrew 1-1/2” (×4)
HAllen Key (×1)
(2)
(4)
(3)

5
4
CRIB ASSEMBLY – REAR LEGS ASSEMBLY
12 13
www.evolurbaby.com/help www.evolurbaby.com/help
CRIB ASSEMBLY - BACK PANEL ASSEMBLY
4a. Align the Left Rear
Leg (9) to the bottom
left side of the Back
Panel (1).
4b. Use the Screws (C), to
fix the Rear Left Leg
to the Back Panel as
shown in the picture.
Tighten the screws
using Allen Key (H).
4c. Similarly follow the
above steps to fix the
Right Rear Leg (10).
5a. Align the Back
Panel (to which
the Rear Legs are
attached), to the
Left and Right
Panel as shown
in the diagram.
5b. Insert the Screws
(G) inside the
holes provided on
the both the Side
Panels as shown.
5c. Ensure that the
alignment is right
and Panels are
firm before you
start using the
crib. Do not
overtighten.
GScrew 2-3/8” (×6)
(1)
(9)
(10)
Screw 1-1/2” (×6)
C

1
14 15
www.evolurbaby.com/help www.evolurbaby.com/help
CONVERSION MODES - DAY BED ASSEMBLY
2
CONVERSION MODES - TODDLER BED ASSEMBLY
1a. In order to convert the crib
to Full-Size bed, you must
first remove the Front panel
of crib.
1b. Fix the Conversion Blocks
(8) at the top of the Right
Front leg and Left Front Leg
attached to the side panel,
with the help of Screws (F)
provided. (Refer the
diagram)
1c. Then attach the Stabilizer
bar using the bolts from the
Front Panel removal.
1d. Make sure to follow the
complete instructions
provided with the Toddler
Guard Rail.
2a. In order to convert
the crib to Full-Size
bed, you must first
remove the Front
panel of the crib.
2b. Then attach the
Stabilizer bar and
Toddler Guard Rail
using the bolts from
the Front Panel
removal.
2c. Make sure to follow
the complete
instructions
provided with the
Toddler Guard Rail.
Guard Rail and Stabilizer Bar (NOT INCLUDED, SOLD SEPARATELY) Guard Rail and Stabilizer Bar (NOT INCLUDED, SOLD SEPARATELY)
FScrew 2-3/4” (×2)
NOTE:
*Make sure mattress support is
at the lowest position.
*Make sure to use Stabilizer
bar that is included with Evolur
Universal Toddler Guard Rail
(SKU- 846) to convert the crib
to day bed.
NOTE:
*Make sure mattress support is
at the lowest position.
*Make sure to use Toddler
Gaurd Rail and Stabilizer bar
that is included with Evolur
Universal Toddler Guard Rail
(SKU-846) to convert the crib
to toddler bed.

16 17
www.evolurbaby.com/help www.evolurbaby.com/help
3
CONVERSION MODES- FULL-SIZE BED ASSEMBLY
WITH FOOTBOARD
FURNITURE CARE INSTRUCTIONS
3a. In order to convert
the crib to Full-Size
bed, you must first
remove the Front
panel of the crib.
3b. Remove the Mattress
Support Panel,
followed by Left and
Right Panels.
3c. Make sure to follow
the complete
instructions provided
with Bed Rails.
Bed Rails (NOT INCLUDED, SOLD SEPARATELY)
ROOM CLIMATE CONTROL:
• Wood, when first cut contains more than 50 percent water. When it is
prepared for furniture construction it is placed in a Kiln and the
moisture content is brought down to 8 to 10 percent. Wood is porous
and responds to its environment. If the room has high humidity it will
absorb it and expand and if the humidity is low it will lose moisture and
shrink.
• It is important that the humidity levels in the room be controlled from
extremes of too much humidity or too little. Furniture should not be
placed close to air- conditioning outlets, fire places, radiators, space
heaters, humidifiers or dehumidifiers. Exposure to extreme variations
of temperature and humidity can damage any fine wood product.
THE IDEAL ENVIRONMENT FOR FINE FURNITURE:
• Fine wood furniture will have fewer problems when its environment is
controlled at a temperature between 65 and 75 degrees and a relative
humidity between 35 and 40 percent. Wood placed in an environment
out side of those limits can and will shrink or expand and may develop
some small cracks which are not material or structural defects.
STICKING DOORS AND DRAWERS:
• With the minor changes in temperature and humidity doors and
drawers may swell and be difficult to open or close. Tolerances have
been builtinto theunits but extreme conditions may still causesticking.
This will adjust back to normal over time but until it does consider
using a dehumidifier or rub candle wax or paraffin on sides that stick.
AVOID DIRECT SUNLIGHT:
• Keep the furniture out of direct sunlight. Ultraviolet rays will fade colors
and in some cases darken them. It can also cause crazing or hair line
cracks in the finish. White finishes will yellow naturally over time and
exposure to direct sunlight will hasten this natural process along with
some woods darkening naturally over time; this is not considered to be
a quality defect.
NOTE:
*Make sure to use the Evolur Bed
Rails (SKU-812) in order to
convert the crib to a Full-size Bed
with Foot board.
*Do not put the mattress directly
on the wooden slats, use either a
Bunky Board, Particleboard, or
low-profile Boxspring before
placing the mattress.

FURNITURE CARE INSTRUCTIONS (cont.) FURNITURE CARE INSTRUCTIONS (cont.)
18 19
www.evolurbaby.com/help www.evolurbaby.com/help
PROPER STORAGE:
• If you need to put your furniture in storage for any period of time do not
store them in a damp basement or hot dry attic. Allow air movement
around the furniture and do not stack anything on it.
IN GENERAL:
• Protect furniture surface from hot or extremely cold items.
• Use coasters under hot or cold beverages.
• Do not use synthetic fabric under accessories or lamps.
• Protect tops from pens, makers and crayons.
• Oils from potpourri and other scented items can damage the finish of
the furniture.
• Do not drag items across the surface of the furniture.
• Allow the surface to breath by rotating your accessories and lamps.
• Do not over polish the furniture, do it only two or three times a year.
Over polishing can distort the natural finish of the product.
• Do not wax the furniture as wax build up can destroy the natural finish
of the product.
• When moving furniture always lift the unit. Do not push or drag it to
avoid damage to legs.
• Keep the furniture level so doors and drawers open and close freely.
• Clean with a damp, not wet, cloth. Use only a mild soap. Do not use
abrasive cleaners.
• Do not scratch or chip the finish.
• Inspect the product periodically, contact Evolur Inc for replacement
parts or questions.
• Do not store the product or any parts in extreme temperatures and
conditions such as a hot attic or a damp, cold basement. These
extremes can cause a loss of structural integrity.
• To preserve the luster of the high-quality finish on your product, it is
recommended to place a doily or felt pad under any items you place
on the finish.
• Clean with a damp cloth, then a dry cloth to preserve the original luster
and beauty of this fine finish.
• Do not use abrasive chemicals.
• Do not spray cleaners directly onto furniture.
• Lift slightly when moving on carpeting to prevent leg breakage.
• Use of a vaporizer near furniture will cause wood to swell and to peel.
YOU DID IT...!
Congratulations Mom & Dad !
It's time to create your dream nursery. A safe, elegant
handcrafted crib that grows with your little one.

Enter our monthly giveaway!
Simply scan the QRcode to register.
Chat with us!
For any questions or concerns or feedback.
Follow us on
to get your nursery featured on our social media.
@EvolurBaby @evolurbaby