EVOLV SIDEKICK User manual

EVOLV.
VERSION 1.0 ™
SIDEKICK™ EQUIPMENT MANUAL
KEEP YOUR CLIENTS.
TAKE THEIRS.
NEVER CONFORM.
ALWAYS

SAFETY INFORMATION
YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY
IMPORTANT. PLEASE READ AND OBEY ALL SAFETY MESSAGES.
SIDEKICK COMPONENTS & SPECIFICATIONS
PORTABLE IS AN UNDERSTATEMENT. THE SIDEKICK WAS BUILT
WITH THE PROFESSIONAL MOBILE TECHNICIAN IN MIND.
SIDEKICK FEATURES
SIDEKICK’S ONE-OF-A-KIND, INNOVATIVE FEATURES ARE MEANT
TO ENHANCE BOTH YOU AND YOUR CUSTOMER’S EXPERIENCE.
SIDEKICK SETUP INSTRUCTIONS
A COMPLETE MOBILE BUSINESS IN A BOX. YOU WILL HAVE
THE SIDEKICK SETUP IN A MATTER OF MINUTES.
SIDEKICK OPERATION
A COMPLETELY CUSTOMIZABLE EXPERIENCE
AT YOUR FINGERTIPS, AND JUST A FEW STEPS AWAY.
PREPARING SOLUTIONS & ADDITIVES
INNOVATION IS NOT JUST IN THE EQUIPMENT, IT EXTENDS
ALL THE WAY THROUGH TO THE SOLUTIONS AND ADDITIVES.
SIDEKICK STORAGE
SETUP AND BREAKDOWN YOUR SIDEKICK FOR
COMPLETE MOBILITY AND EQUIPMENT PROTECTION.
SIDEKICK MAINTENANCE
YOU’VE PURCHASED THE BEST EQUIPMENT ON THE
MARKET, NOW MAKE SURE TO PROTECT YOUR INVESTMENT.
TROUBLESHOOTING
SIDEKICK RUNS ITS OWN DIAGNOSTICS TO DETECT PROBLEMS
FASTER AND TAKES THE GUESSWORK OUT OF FIXING THE ISSUE.
ELECTRICAL CONFIGURATIONS
U.S. AND INTERNATIONAL VOLTAGE
SETTING DIAGRAMS
SERIAL NUMBER LOCATION
REGISTER YOUR EQUIPMENT TO RECEIVE THE MOST OUT OF YOUR
PURCHASE AND TO INITIATE YOUR 2 YEAR WARRANTY!
4
6
8
11
15
20
23
26
34
38
39
CONTENTS

www.evolvsunless.com
4
SAFETY INFORMATION
Your safety and the safety of others are very important. We have provided important safety information
in this manual. Always read and obey all safety messages.
It is the responsibility of the owner and operator of the EVOLV. Sidekick to comply with all appropriate
safety and health laws, as well as other applicable national, state and local laws and ordinances when op-
erating and maintaining EVOLV. Equipment. EVOLV. products are to be operated only by those who have
been professionally trained.
Read all safety information provided before use of the EVOLV. Sidekick.
1. Carefully read this manual and follow all instructions given hereof.
2. Heed all warnings laid out in this manual, as well as, all warnings located on the unit.
3. Do not modify the Sidekick plug. Always plug the power cord into a properly configured grounded
outlet only.
4. If the provided plug does not fit into your outlet, consult an electrician for replacement of the outlet.
5. Units are available in 115 Volt, 10 AMP and 230 Volt, 5 AMP configurations. Never use a 115 Volt spray
gun with a 230 Volt base unit and vice versa.
6. Never disconnect the plug by pulling on the cord. To disconnect from the outlet, grasp the plug
not the cord.
7. Close supervision is necessary when this product is used by, on, or near children or invalids.
8. Do not immerse EVOLV. equipment in liquids. Do not operate the spray gun if it is wet or leaking.
9. Use this product only as intended per the instructions in this manual. Refrain from use
of attachments or solutions not recommended by Sunless, Inc.
10. It is recommended that the EVOLV. Sidekick be used on a dedicated 110V/15AMP or 230V/8AMP
circuit; that is, a single outlet circuit which powers only the Sidekick and has no additional outlets
or branch circuits. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall
outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric shock or fire. Periodically examine the cord of the
EVOLV. Sidekick, and if its appearance indicates damage or deterioration, unplug it, and discontinue
use of the Sidekick. Please contact EVOLV. Technical Support at [phone] for an exact
replacement. Protect the power cord from physical or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets,
and the point where the cord exits the Sidekick.
DANGER!!: To reduce the risk of burns, fire, electric shock, death or injury to persons, read
the following important safety precautions and all instructions before operating/using the
EVOLV. Sidekick. Interior components of the spray gun or base unit are not to be disas-
sembled except by trained and qualified personnel.
YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY
IMPORTANT. PLEASE READ AND OBEY ALL SAFETY MESSAGES.

5
www.evolvsunless.com
SAFETY INFORMATION
11. Keep cords away from heated surfaces.
12. Do not allow water to accumulate on the floor around the EVOLV. Sidekick.
13. Use only the flex hose supplied with this unit. Do not make a substitution for any reason.
These hoses must be inspected periodically and replaced when necessary.
14. Use a respirator, mask, or nose filter whenever there is a chance that vapors may be inhaled,
especially with prolonged usage.
15. Do not carry the EVOLV. Sidekick while spraying.
16. Keep the EVOLV. Sidekick at least four feet from the spraying area at all times.
17. Never operate the EVOLV. Sidekick while drowsy or impaired.
18. Consult a physician before use if you are pregnant or think you may be pregnant,
or if you have a diabetic condition.
19. EVOLV. sunless formulations are not a sunscreen or a substitute for proper sun protection.
20. Never handle the plug, cord, base unit, or spray gun with wet hands.
21. The spray gun may become hot after spraying, especially the front of the spray gun. Allow the unit
to cool before touching. The spray gun must be positioned no closer than 6 inches from the skin.
22. When the Sidekick is not in use, please be sure to disconnect and unplug the unit. Disconnect
the spray gun from the hose and place it into the storage compartment.
23. To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture.
24. Do not spray directly at or into the EVOLV. Sidekick.
25. Do not allow the EVOLV. Sidekick to run unattended.
26. Your unit is equipped with a Residual Current Breaker with Overload, RCBO. RCBO’s are designed
to disconnect the electrical circuit quickly in case of a ground fault or electrical overload. The RCBO
must be tested monthly to ensure its effectiveness.
(See “Testing & Resetting the RCBO” on pg. 29)
YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY
IMPORTANT. PLEASE READ AND OBEY ALL SAFETY MESSAGES.

www.evolvsunless.com
6
SIDEKICK COMPONENTS & SPECS
PORTABLE IS AN UNDERSTATEMENT. THE SIDEKICK WAS BUILT
WITH THE PROFESSIONAL MOBILE TECHNICIAN IN MIND.
SIDEKICK CONTROLLER
1) Air Speed Button
Controls the Air Speed Level
NOTE: When the Sidekick
is turned on air blows constantly
2) Heat Level Button
Controls the Heat Intensity Level
3) Power Button
Controls the on and off cycle
1
23
45
6
1
2
3
4
5
6
7
8
SIDEKICK COMPONENTS
controller
base
base
spray gun
1
2
3
7
8
9
10

7
www.evolvsunless.com
24”
(60 cm)
(45 cm)
17.5”
15.0”
(38
CM)
ELECTRICAL
115 Volt- 10 Amp
(230 Volt - 5 Amp)
WEIGHT
26 lBS.
(18.8 KG)
SIDEKICK COMPONENTS & SPECS
PORTABLE IS AN UNDERSTATEMENT. THE SIDEKICK WAS BUILT
WITH THE PROFESSIONAL MOBILE TECHNICIAN IN MIND.
SIDEKICK BASE
1) Control Center
Contains Air Speed, Heat Level, and Power Buttons
2) Storage Compartment
Allows for storage of: 2 Formulation Bottles, 2 Additives,
1 Nozzle Tip Tool, 1 Spray Gun, 2 Spare Cartridges
3) Extension Handle and Spray Gun Dock
3 Stage Telescoping Handle, with Spray Gun Dock
4) Power Cord
Contained in a retractable cord reel inside of the base
5) Hose Connector
Connects the flex hose to the spray gun
NOTE: Always verify electrical configuration match
(refer to pg. 38)
6) Hose End Lock
Locks the hose to the base
NOTE: An indent in the hose wrap plate
allows for the hose connector to lock into place
7) Hose Wrap Plate
8) Flex Hose
SIDEKICK SPRAY GUN
1) Spray Gun Hook
Used to hang the Spray Gun on the Spray Gun Dock
2) Trigger
Activates solution flow
3) Formulation Intensity Adjustment Knob
Adjusts the amount of solution which sprays through
the spray gun. See pg. 18 for settings
4) Formulation Cartridge
100 mL of solution capacity
5) Formulation Cartridge Cap
Flip top open and close, with easy filling
6) Cartridge Release Button
Releases Formulation Cartridge from Spray Gun
7) Needle Tip
8) Fluid Nozzle
9) Air Cap
Used to alter spray pattern
10)Air Cap Retainer
SIDEKICK SPECIFICATIONS

www.evolvsunless.com
8
FEATURES
SIDEKICK
“
“
SIDEKICK’S ONE-OF-A-KIND, INNOVATIVE FEATURES
ARE MEANT TO ENHANCE BOTH YOU AND YOUR
CUSTOMER’S EXPERIENCE.

9
www.evolvsunless.com
SIDEKICK FEATURES
HEAT-INFUSED APPLICATION
HEAT IS LITERALLY INFUSED ONTO THE BODY AND INTO THE SOLUTION
WITH OUR PATENT-PENDING 2 STAGE PROCESS.
COMFORT-CONTROL CENTER
MAXIMIZE COMFORT AND ADJUST FOR THE PERFECT APPLICATION.
Using the Sidekick’s™ state-of-the-art, LED-enhanced Control Center, you can
control air speed ensuring (VLO) very low over spray, and heat levels ensuring a
custom comfort level for everyone.
PERFECT-CONTROL SPRAY PATTERN
SPRAY PATTERN IS ALWAYS IN YOUR CONTROL FOR THE PERFECT
APPLICATION EVERY TIME.
With an easy-to-access adjustable spray nozzle, and trigger controlled volume ad-
justment, you can deliver both wide spread diffusion and pinpoint accuracy from
any angle, creating a custom contoured application every time.
QUICK-CHANGE CARTRIDGE SYSTEM
CHANGE OUT CARTRIDGES WITH A SINGLE CLICK.
Encased inside the Sidekick’s spray gun is a cutting edge, easy-to-maintain Car-
tridge Formula System. With an easy-to-fill, mess-free, flip top reservoir, loading
solution has never been easier.
STAGE 1
Warms and prepares the skin for ultimate comfort and maximum absorption
ensuring a completely dry application every time.
STAGE 2
A gently warmed spray nozzle infuses heat directly into our formulas
literally creating a heat-infused application every time.
FEATURE DESCRIPTIONS
SIDEKICK’S ONE-OF-A-KIND, INNOVATIVE FEATURES ARE MEANT
TO ENHANCE BOTH YOU AND YOUR CUSTOMER’S EXPERIENCE.

www.evolvsunless.com
10
POWERFULLY QUIET ENGINE
ENGINEERED FOR AN UNBELIEVABLY QUIET APPLICATION.
Among Sidekick’s most advanced features is a powerful, yet subtle engine which
allows for a conveniently quiet application from start to finish. Now your clients
can enjoy a relaxing airbrush tanning experience without being distracted.
DURABLE SUPERFLEX HOSE AND RETRACTABLE CORD
UNMATCHED STRENGTH, FLEXIBILITY, AND MOBILITY.
The Sidekick’s durable superflex hose is specially designed to be super lightweight
without sacrificing strength and flexibility. This lightweight, flexible hose allows for
optimum weight balance, and minimizes fatigue during applications. Durable flex-
ibility also allows for easy, wrap-and-go mobility, without harmful wear and tear.
Plus with an added retractable cord, becoming mobile has never been easier.
ALL-TERRAIN WHEELS
OVERSIZED, SOFT AND EASY-TO-ROLL.
The Sidekick’s all terrain wheels are soft, oversized and built with precision bear-
ings. Leap small curbs in a single bound, and maneuver the Sidekick around with
quiet, smooth mobility.
TELESCOPING MULTI-PURPOSE HANDLE
FULLY-EXTENDING HANDLE, WITH EASY-ACCESS SPRAY GUN DOCK.
With a 3 stage fully extending, retractable handle and easy-access spray gun dock,
the Sidekick is setting the new standard for portability and ease-of-use. Use the
spray gun dock in between sessions for quick-draw applications.
STORAGE MANAGEMENT SYSTEM
SLEEK, FUNCTIONAL AND UNCOMPROMISING.
The Sidekick’s distinct shell is both sleek and functional. Encased inside the ultra-
modern design is enough space to store your Sunless formulations and additives,
as well as the Sidekick’s spray gun, and 2 extra cartridges.
SIDEKICK FEATURES
SIDEKICK’S ONE-OF-A-KIND, INNOVATIVE FEATURES ARE MEANT
TO ENHANCE BOTH YOU AND YOUR CUSTOMER’S EXPERIENCE.

11
www.evolvsunless.com
INSTRUCTIONS
SIDEKICK SETUP
“
“
A COMPLETE MOBILE BUSINESS IN A BOX.
YOU WILL HAVE THE SIDEKICK SETUP IN
A MATTER OF MINUTES.

www.evolvsunless.com
12

1. Carefully remove all components
from the packaging. Inspect parts
and immediately report any
shipping damage.
2. Lift the door latch and open the
Sidekick storage compartment
by pulling the door towards you.
3. Carefully remove your spray gun.
4. Uncoil your flex hose counter
clockwise from the hose wrap
plate at the back of your unit.
You will need to first pull
down on the hose connector,
in order to release it from the
hose end lock.
5. Attach your spray gun to your flex
hose. Line up the notches on the
hose and spray gun connectors.
Push the hose connector into the
spray gun connector and tighten
the hose-locking ring.
NOTE: Verify that hose connector and spray
gun connector match your appropriate
electrical configuration. Turn the hose-locking
ring counter clockwise to tighten.
See pg. 38 for configuration diagrams
Lift the door latch to
release the storage
compartment and pull
the storage compartment
towards you
Uncoil flex hose counter
clockwise from the hose
wrap plate at the back
of your unit
After lining up the notches
push the hose connector
into the spray gun. Turn
the hose-locking ring
counter clockwise until
it is tight
SIDEKICK SETUP
A COMPLETE MOBILE BUSINESS IN A BOX. YOU WILL HAVE
THE SIDEKICK SETUP IN A MATTER OF MINUTES.

13
www.evolvsunless.com
6. Extend the Sidekick handle.
Push the button on top of the
handle to extend or retract it
through its three locking stages.
7. Locate the spray gun dock.
This is at the top of your handle.
8. Attach your spray gun to the spray
gun dock by lining up the hook on
the top of the spray gun with the
spray gun dock.
9. The Sidekick is equipped with a
retractable power cord reel. Pull the
power cord gently out of the unit
until it clicks and holds in place.
To retract the power cord, pull the
power cord slightly towards you
and then allow the cord to retract
back into the unit.
10. Plug your EVOLV. Sidekick unit
into a properly grounded electrical
outlet. Make sure that the
configuration of the electric
outlet you are connecting to is
the same as the plug on your unit.
Do not attempt to connect the unit to the wrong
electric outlet configuration as this can damage
your unit and void your warranty.
Use this dock to attach
the spray gun for short
period storage
Use this hook to attach
the spray gun to the spray
gun dock located at the top
of the extension handle
Attach the hook
to the spray gun dock
Pull the power cord gently
out of the unit until it clicks
and holds in place
SIDEKICK SETUP
A COMPLETE MOBILE BUSINESS IN A BOX. YOU WILL HAVE
THE SIDEKICK SETUP IN A MATTER OF MINUTES.

www.evolvsunless.com
14
11. After plugging in your Sidekick,
the Control Center will flash through
a series of red, green and white lights.
When the unit is ready, two green
lights will flash on either side of the
control center.
12. Power up your Sidekick by
pressing the power button (=)
once. The power button is located
on the control center. Press the
power button again to turn off
the unit. If the heat option has
been used, upon turning the unit
off, you will notice the air continues
to blow for a three second cool
down cycle.
NOTE: Three second cool down cycle
only occurs if one of the 3 heat settings
were used while the unit was on.
13. Once your unit is on you will see
the first white light illuminate, this
light indicates a low air speed
setting. When the unit is powered
on, the air turbine will be running
at all times.
14. Please see pg. 16-19 for further
instructions on how to set the
air speed, heat level, formulation
intensity, and spray pattern.
Power up your Sidekick
by pressing the power
button once
Once your unit is on you
will see the first white light
illuminate
SIDEKICK SETUP
A COMPLETE MOBILE BUSINESS IN A BOX. YOU WILL HAVE
THE SIDEKICK SETUP IN A MATTER OF MINUTES.

15
www.evolvsunless.com
OPERATION
SIDEKICK
“
“
A COMPLETELY CUSTOMIZABLE EXPERIENCE
AT YOUR FINGERTIPS, AND JUST
A FEW STEPS AWAY.

www.evolvsunless.com
16
CUSTOMIZING YOUR TANNING EXPERIENCE
AIR SPEED SETTINGS
The EVOLV. Sidekick features four unique adjustment options to customize the tanning experience.
It is equipped with adjustable air speed, heat intensity, formulation intensity, and spray pattern.
There are three separate air speed settings available on your unit; low, medium and high. We recommend
the medium air setting for most applications. By simply pushing the air speed button on the control cen-
ter, you can cycle through these settings.
NOTE: If the Sidekick is turned off, but not unplugged, the Sidekick will automatically remember the user’s previous air and heat settings.
1 WHITE LIGHT
This represents low air speed. This setting will provide the user with the lowest
velocity spray. This application is generally used for contouring, when using the
pinpoint accuracy spray pattern. Upon turning your unit on, initially or after un-
plugging, the air speed will automatically be set on low air speed.
2 WHITE LIGHTS
This represents medium air speed. This setting is recommended for most tan-
ning applications, when using the wide spread diffusion spray pattern. Medium
air speed can be attained by pressing the air speed button once.
3 WHITE LIGHTS
This represents high air speed. This setting will provide the user with the widest
spray pattern width. High air speed can be attained by pressing the air speed
button twice.
SIDEKICK OPERATION
A COMPLETELY CUSTOMIZABLE EXPERIENCE AT YOUR
FINGERTIPS, AND JUST A FEW STEPS AWAY.

17
www.evolvsunless.com
HEAT LEVEL SETTINGS
There are four separate heat level settings on your unit; off, low, medium and high. By simply pressing the
heat level button on the control center, you can cycle through these settings. The appropriate heat level
should be customized for each individual user and customer.
NOTE: If the Sidekick is turned off, but not unplugged, the Sidekick will automatically remember the user’s previous air and heat settings.
NO RED LIGHTS
This represents that no heat option has been selected. A low level of warm air will
still blow from the spray gun since the air turbine is also designed to produce heat.
1 RED LIGHT
This represents low heat intensity. This setting can be attained by pressing
the heat level button once.
2 RED LIGHTS
This represents medium heat intensity. This setting can be attained by pressing
the heat level button twice.
3 RED LIGHTS
This represents high heat intensity. This setting can be attained by pressing
the heat level button three times. Please be aware that if the unit is on low air
speed (one white light), the high heat intensity (three red lights) option will not
be available.
NOTE: When the heat setting is on high heat intensity (three red lights) pushing the heat level button again
will change the heat level back to medium heat Intensity. If it is pushed one more time, the unit will be at
low heat intensity.
SIDEKICK OPERATION
A COMPLETELY CUSTOMIZABLE EXPERIENCE AT YOUR
FINGERTIPS, AND JUST A FEW STEPS AWAY.

www.evolvsunless.com
18
FORMULATION INTENSITY KNOB SETTINGS
The formulation intensity adjustment knob controls the amount of solution that is sprayed when the trigger is
pulled. The recommended intensity knob setting is 1 full turn from the closed position, for the optimal amount
of formulation. Inexperienced users should turn the knob between 3/4 and 1 full turn. More experienced users
may find that a 1 to 1-1/4 turn is ideal. If the intensity knob is in the closed position, formulation will not spray
out of the nozzle when the trigger is pulled. Please be aware that the intensity adjustment knob is preset
to the optimized setting. There is no need to adjust this knob initially. As you become more accustomed to
spraying with the EVOLV. Sidekick, you can increase or decrease the solution flow by simply turning the for-
mulation intensity knob to the desired position. To increase solution flow turn the knob counter-clockwise. To
decrease solution flow turn the knob clockwise, towards the closed position. In general, adjust the air speed
and formulation intensity knob to dispense 50 mL per session on the average sized person.
CLOSED POSITION
When the formulation intensity knob is in the closed
position, solution will not spray out of the nozzle when
the trigger is pulled. To locate the closed position,
turn the intensity knob clockwise until it stops
IDEAL SETTINGS
FOR INEXPERIENCED USERS
Turn the formulation intensity
knob 3/4 to 1 full counter-
clockwise turn from the
closed postion
3/4 counter-
clockwise turn
from closed
postion
1 full counter-
clockwise turn
from closed
postion
1-1/4 counter-
clockwise turn
from closed
postion
IDEAL SETTINGS
FOR ADVANCED USERS
Turn the formulation intensity
knob 1 to 1-1/4 full counter-
clockwise turn from the
closed postion
SUGGESTED FORMULATION INTENSITY KNOB RANGE
SIDEKICK OPERATION
A COMPLETELY CUSTOMIZABLE EXPERIENCE AT YOUR
FINGERTIPS, AND JUST A FEW STEPS AWAY.





19
www.evolvsunless.com
SPRAY PATTERN SETTINGS
Every EVOLV. spray gun comes equipped with two spray pattern options, wide spread diffusion and pin-
point accuracy. The spray pattern can be adjusted by simply turning the air cap. The air cap may be warm
if your unit is on. Please turn off your Sidekick before changing spray patterns. A wide spread diffusion
spray pattern can be attained by turning the knobs on the air cap so that they are vertical.
A pinpoint accuracy spray pattern can be attained by turning the knobs on the air cap slightly coun-
ter-clockwise. The knobs should be located at 11 and 5 o’clock. Pinpoint accuracy is generally used for
contouring applications.
PIN POINT ACCURACY
SPRAY PATTERN
WIDE SPREAD DIFFUSION
SPRAY PATTERN
NOTE:
For basic airbrush tanning and drying
with heat techniques, see provided
Quick-Start Training Guide.
SIDEKICK OPERATION
A COMPLETELY CUSTOMIZABLE EXPERIENCE AT YOUR
FINGERTIPS, AND JUST A FEW STEPS AWAY.

www.evolvsunless.com
20
SOLUTIONS
PREPARING
& COMPLEMENTING ADDITIVES
“
“
INNOVATION IS NOT JUST IN THE EQUIPMENT,
IT EXTENDS ALL THE WAY THROUGH TO THE
SOLUTIONS AND ADDITIVES.

21
www.evolvsunless.com
1. Adding solution can be accomplished
while the cartridge is either removed
or attached to the spray gun by
simply flipping open the cartridge
cap. Before removing the formulation
cartridge, flip open the cartridge cap
to relieve the pressure in the
cartridge. Removal of the cartridge
can be completed by pushing the
green cartridge release button and
pulling the cartridge straight back.
2. Begin by shaking your desired
solution bottle to make sure it is
mixed well. Verify that the safety
seal of the solution bottle is removed.
Simply turn the black cap counter-
clockwise, remove the cap, if a safety
seal is present please discard it
and reattach the black cap. Next,
flip open the spout on the solution
bottle cap and begin pouring the
desired EVOLV. Sunless formulation
through the EZ fill spout and into
the cartridge. Please keep in mind
that 50 mL is enough for 1 tan
and 100 mL is sufficient for 2 tans.
3. Choose the desired color, accelerator,
and fragrance additives.
4. Use the eyedropper inside of your
additive bottle. Add 1 full dropper
into the formulation cartridge at
a time. Please keep in mind that
1 full dropper is enough for 50 mL.
Push the green cartridge
release button to release
formulation cartridge
Flip open formulation
cartridge cap
Choose the desired
combination of additives
SOLUTIONS & ADDITIVES
INNOVATION IS NOT JUST IN THE EQUIPMENT, IT EXTENDS
ALL THE WAY THROUGH TO THE SOLUTIONS AND ADDITIVES.