Exalux CONTROLSKY User manual

USER MANUAL
CONTROLSKY

CONTROLONE
Getting started...
EXALUX™ CONTROL SKY is a 5-in-1 wireless DMX controller
especially designed to control up to 20 the SkyPanel®with
sense and simplicity.
CONTROL SKY works perfectly with all CRMX by LumenRadio™
receivers.
MEMORIES
Push >2s to save
Push <1s to restore
Always deploy the antenna for optimal range transmission
ANTENNA
5VDC
INPUT
DMX
INPUT
10-24VDC
INPUT
DMX
OUTPUT
LOCKBLACK OUT
Push to enter black out mode
Push to exit black out mode
Long push to lock the screen & the knobs
Push to unlock
OFF/ON/SCREEN OFF
Select «screen off» position to turn off the display and save battery
DMX data is still sent to the equipment
CRMXCRMX LINK/UNLINK
Push 1s to enable the CRMX transmitter
Push 1s to disable the CRMX transmitter
Push 3s to unlink all CRMX devices
Push 1s to link a CRMX devices
MASTER KNOB
Turn and push to select the App
Turn to adjust the master
Push = next fader
SET KNOB
Turn to set, push to valid
Push = previous fader
Use your finger or stylus to launch and control applications
TOUCH SCREEN

SKY CONTROL
RECORDER
PLAYER
RECORDER APP allows to record
512 DMX channels in real time.
8 memories | 80s recording @44Hz
max
PLAYER APP allows to play the
DMX memories that have been
recorded with the FADER, SKY and
RECORDER Apps
FADER
FADER APP works the exact same
way than your hardware DMX
console you used for years. Every
fader is linked to a DMX address.
TX
TX APP turns the CONTROL SKY
into a CRMX transmitter. The DMX
data bytes received on the DMX
input are wirelessly transmitted by
the integrated CRMX transmitter.
SKY APP allows to control the
SkyPanel® when DMX P30 mode
is set (CCT+GM, HSI, RGBW, (X,Y),
Effects, Source Matching, Filters).

SELECT AN APP
ENTER THE APP
TO ENTER THE APP
HOME is the main screen when you switch on your CONTROL SKY.
Touch the display or use the right knob to select an App.
HOME
INFORMATION SCREEN
SELECT AN APP
ENTER THE APP

SET MASTER LEVEL
NEXT FADER
SET THE MASTER LEVEL
FULL ON
MASTER ALL FADERS
SET THE FADER
PREVIOUS FADER
SAVE TO MEMORY
RESTORE MEMORY
SHORTCUT TO DMX
PAGE
PREVIOUS FADER
SET THE FADER LEVEL
MASTER THE FADER
BACK TO HOME
FADER APP works the exact same way than your hardware DMX console you
used for years. Every fader is linked to a DMX address.
FADER
>2’’
<1’’

STOP RECORDING
DELETE MEMORY
SELECT A MEMORY
TO RECORD DMX IN
DMX INPUT STATUS
GREEN : DMX OK
RED : NO DMX
BACK TO HOME
RECORDER APP allows to record all DMX frames received on the DMX input.
You can record sequences with a maximum duration of 80 seconds at a
frequency of 44Hz on one of the 8 memories.
RECORDER
START RECORDING
Recording stops automatically
after 80 seconds.
The recorded sequences
can only be playback in the
«PLAYER» application.

SELECT A BANK
BACK TO HOME
PLAYER APP allows you to play the DMX memories that have been recorded
with the FADER, RECORDER and SKY Apps.
PLAYER
CHANGE THE
MEMORY NAME TO SELECT A
MEMORY
TO SELECT A
MEMORY

SKY APP allows to control the SkyPanel® when DMX P30 mode is set.
Operation modes are : CCT+GM, HSI, RGBW, [X,Y], Effects, Source Matching,
Filters.
SKY
SAVE TO MEMORY
RESTORE MEMORY
UP/DOWN
SCROLLING
FIXTURE SELECTION
(UP TO 20)
BACK TO HOME
FIXTURE SETTINGS
>2’’
<1’’
SET COLOUR 1
CONFIGURE FIXTURE
GENERAL SETTINGS
SET COLOUR 2

FIXTURE SETUP
Allows to set the DMX operation modes : CCT+GM, HSI, RGBW, [X,Y], Effects,
Source Matching, Filters for each colour 1 and colour 2.
SKY
ENABLE / DISABLE
THE FIXTURE
MODE SELECTION
CHECK TO ACTIVATE
COLOUR 2
BACK TO HOME
MODE SELECTION
Please read the SkyPanel user
manual before using the SKY
APP.
The SkyPanel must be set in
DMX mode P30 before using
the SKY APP.

SKY
SET THE FADER
PREVIOUS FADER
SAVE TO MEMORY
RESTORE MEMORY
UP/DOWN
SCROLLING
FIXTURE SELECTION
>2’’
<1’’
BACK TO HOME
FIXTURE SETTINGS
SET MASTER LEVEL
NEXT FADER
SET COLOUR 1
CONFIGURE FIXTURE
GENERAL SETTINGS
SET COLOUR 2
SET DMX ADRESS
GENERAL SETTINGS
Allows to set main parameters such as Strobe, Fan, CrossFade between
colour 1 and colour 2 and Master.

SKY
SET THE FADER
PREVIOUS FADER
SAVE TO MEMORY
RESTORE MEMORY
UP/DOWN
SCROLLING
FIXTURE SELECTION
>2’’
<1’’
BACK TO HOME
FIXTURE SETTINGS
SET MASTER LEVEL
NEXT FADER
SET COLOUR 1
CONFIGURE FIXTURE
GENERAL SETTINGS
SET COLOUR 2
SET DMX ADDRESS
COLOUR SETTINGS
Allows to set coulour parameters of colour 1 or colour 2 for the selected
colour mode.

TX APP turns the CONTROL SKY into a CRMX transmitter.The DMX data bytes
received on the DMX input are wirelessly transmitted by the integrated CRMX
transmitter.
TX
DMX INPUT STATUS
BACK TO HOME
the CRMX transmitter is
automatically switched on
when the application is active.

SYSTEM APP allows you to reset the memories, adjust the display brightness
and set a pin code.
SYSTEM
SCREEN BRIGHTNESS
[-]
RESET ALL FADER
MEMORIES
PIN CODE
ENABLE/DISABLE
SET PIN CODE
RESET ALL SKY
MEMORIES
RESET ALL
MEMORIES
3 ’’
RESET ALL RECORDER
MEMORIES
3 ’’
SCREEN BRIGHTNESS
[+]
3 ’’
3 ’’

TECHNICAL SPECIFICATIONS
2,4GHz CRMX by LumenRadio™
TFT 5.0’’ capacitive touch super bright display
Link range : up to 1000 meters line-of-sight*
5VDC (USB) | 10-24VDC (XLR4) Input / ~5W
XLR5 DMX input (M) & output (F)
180x154x50 mm |700g
FEATURES
1 DMX universe
8 tact switches to save/reload memories
Black out function
Lock / unlock function
Runs up to 7h with 10Ah/36Wh PowerBank
Fully compatible with EXALUX™ CONNECT
* depending on the receiver
TECHNICAL
SPECIFICATIONS
232
109
66
154
180 50
120
12
70
127
Ø 4,5
Ø 4,5

DMX
RX100s
RECEIVER
RX100
RECEIVER
DMX
EXORAA
LEDMASTER NEO
DIMMER
CONNECTONE
CONNECTRX100
CONNECTRX100s
ONE
CONTROLSKY
ECO-SYSTEM
OR
CONNECT ONE DMX CONSOLE
iOS/Android
DEVICES
DMX
CONTROL SKY

EXALUX, 1 rue de la Noë 44322 Nantes Cedex 3 France | [phone] | [e-mail]
exalux.eu
DESIGNED
IN
NANTES
MADE
IN
FRANCE
LIGHT CONNECT CONTROL DIMMING