Expolite TourSport 21 CM User manual

TourSpot 21 CM
- Manual -

PART 4 USINGADMX512 CONTROLLER....................................13.
4.1--BASICADDRESSING.................................................................13.
4.2--CHANNELASSIGNMENT............................................................13.
4.3--BASIC INSTRUCTIONS FOR DMX512 OPERATION (STAGE 1).....16.
PART 3 DISPLAY PANEL OPERATION.........................................8.
3.1--BASIC..........................................................................................8.
3.2--MENU..........................................................................................9.
3.3--STATIC......................................................................................10.
3.4--AUTO.........................................................................................10.
3.5--ADDRESS..................................................................................10.
3.6--RUN...........................................................................................11.
3.7--PERSON...................................................................................11.
3.8--ID.............................................................................................. 11.
3.9--EDIT ..........................................................................................11.
3.10--SETTINGS ...............................................................................12.
3.11--PASSWORD .............................................................................12.
PART 1 PRODUCT (GENERAL)....................................................1.
1.1--PRODUCT INTRODUCTION.........................................................1.
1.2--PRODUCT FEATURES.................................................................1.
1.3--TECHNICALSPECIFICATIONS.....................................................2.
1.4--PHOTOMETRIC DATA..................................................................3.
1.5--SAFETYWARNING......................................................................4.
PART 2 INSTALLATION...............................................................5.
2.1--MOUNTING...................................................................................5.
2.3--SETTING UP WITHADMX512 CONTROLLER.................................6.
2.3-1--DMX512 ADDRESSING WITHOUT ID ADDRESSING......................................6.
2.3-2--DMX512 ADDRESSING WITH ID ADDRESS..................................................6.
2.2--POWER CONNECTION..................................................................5.
3.12--SAVE .......................................................................................12.
PART 5 APPENDIX..................................................................... 17.
5.1--TROUBLE SHOOTING...............................................................17.
5.2--MAINTENANCE........................................................................ 18.
ABLE OFCONTENTS
T
No display
1) Power connection error
2) Power switch damaged
3) Display board damaged
1)Check allpower connections
2) Replace power switch
3) Replace display board
LED MODULE on,
but no control
from display 2) Display board damaged 2) Replace display board
LEDs of the same
color are not lit LED PCB damaged
Check and Replace PCB board
SITUATION CAUSE PART ORDERNUMBER
ACTION
LED module on,
LEDs of all colors
are not lit
1) MAIN PCB damaged 1) Replace main PCBboard
Display normal,
but no response
to DMX 512
controller
1) Signal connection error
2) DMX Addresserror
1)Check and replacesignalcable
2) Check and reset DMX address
3) Master & slavemode error
4) ID error
3) Check and reset the working mode
4) Check andreset ID address
5.1 TROUBLE SHOOTING
16-03-0030-04
26-2A-LED307DI-00
1) Keyboard damaged 1) Replace keyboard
26-2A-LED307DI-00
26-2A-LED307DI-00
26-2A-307LED-00
2) LED PCB damaged 2) Replace PCB board 26-2A-307LED-00
26-2A-LED307DI-00
LED MODULE
17
5 APPENDIX
4) Fuse damaged 4)Replace the Fuse
5APPENDIX
2009.12.9

1.1 PRODUCTINTRODUCTION
This product is designed for indoor use. Suitable applications include
wash or effect lighting forarchitectural, stage ornightclub applications.
This product can also be installed for use in signage and advertising
using the dynamicfunctions available withDMX512 control. Directinput
of DMX512 signal allows the units to be controlled from any DMX512
controller. This product can be operated as a single unit or in multiple
units for largeapplications.
The specially developed controller that allows the product to be
controlled independent of the DMX512 controller enables the user to
create and edita wide rangeof custom programs. All programs can be
touch-button displayed or scheduled to START and END at scheduled
times. When programshave been createdor edited inthe controller,it is
also possible totrigger these programsusing the DMXIN function when
connected to aDMX512 controller.
1.2 PRODUCTFEATURES
LED FIXTURE
* RGB Dimmer0-100%
* Strobe
* Automatic programs
* LCD display
* Display control'lock-out'
* Direct DMX512input
* Independant IDaddress
* Stand-alone/ Slave
1 PRODUCT(GENERAL) 1
1PRODUCT (GENERAL)
2009.12.9
4.3 BASIC INSTRUCTIONSFOR DMX512
OPERATION (STAGE 1)
MASTER DIMMER
CH1 controls theintensity of thecurrently projected color
When the slideris at thehighest position (255)the intensity ofthe output
is the maximum
RED, GREEN &BLUE COLOR SELECTION
CH2, CH3 &CH4 control theintensity ratio ofeach of theRED, GREEN &
BLUE LEDs.
When the slideris at thehighest position (255)the intensity ofthe color is
the maximum.
CH2, CH3 &CH4 can becombined together tocreate over 16million
colors.
COLOR MACROS
CH5 selects therequired COLOR MACRO
CH5 has priorityover CH2, CH3, CH4 andCH6
CH1 is usedto control theintensity of theCOLOR MACRO
STROBE
CH 6 controlsthe strobe ofCH1 to Ch5
ID ADDRESS SELECTION
CH9 is usedto select thetarget ID address.
Each independent DMXaddress may haveupto 66 independentID
addresses.
An IDaddress of 0will activate allID address locations.
AUTO
CH7 selects thepreset AUTO programsAT.01-AT10or the customAUTO
programs PR.C1-PR.10
When activating thecustom AUTO programs PR.C1to PR.10 thenit is
possible to controlthe
Step time andfade time usingCh2 and Ch3respectively.
16
4 USING ADMX512 CONTROLLER 2009.12.9

1.3 TECHNICALSPECIFICATIONS
LED MODULE
Dimensions
LED MODULE:
Voltage
Rated Power 7 X 3WTri-RGB
Weight
LED/Unit
Cooling Forced air convection
240 x 210 x160mm
2.5Kg
100~240V...50/60Hz
35W
1 PRODUCT(GENERAL) 2
Environment Temperature -20 ~40
2009.12.9
9
ID21
ID22
210
211
CHANNEL FUNCTIONVALUE
15
4 USING ADMX512 CONTROLLER
ID20
200 209
2009.12.9
ID64
ID65
ID66
253
254
255
ARC 1
BLUE
1
2
0 255
CHANNEL FUNCTIONVALUE
3
0 255
0 255
GREEN
RED
ARC 1+D
BLUE
1
2
0 255
CHANNEL FUNCTIONVALUE
3
4
0 255
0 255
0 255
GREEN
RED
MASTER DIMMER

1.4 PHOTOMETRICDATA
PHOTOMETRIC DATA
1 PRODUCT(GENERAL) 32009.12.9
0 20
21 30
31 40
41 50
51 60
61 70
71 80
81 90
91 100
101 110
AUTO 1
AUTO 2
AUTO 3
AUTO 4
AUTO 5
AUTO 6
AUTO 7
AUTO 8
AUTO 9
111 120 AUTO 10
AUTO
No function
7
CUSTOM 2
CUSTOM 3
CUSTOM 4
CUSTOM 5
CUSTOM 6
CUSTOM 7
CUSTOM 8
CUSTOM 9
CUSTOM 10
121 130
131 140
141 150
151 160
161 170
171 180
181 190
191 200
201 210
0 255
CUSTOM 1
8
211 220
221 255
When using CH7,AUTO01-AUTO9, this function activated
No function
AUTO SPEED ADJUSTMENT
CHANNEL FUNCTIONVALUE
14
4 USING ADMX512 CONTROLLER
ID ADDRESS
ID1~ID66
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
ID9
ID10
ID11
ID12
ID13
ID14
ID15
0 9
10 19
20 29
30 39
40 49
50 59
60 69
70 79
80 89
90 99
100 109
110 119
120 129
130 139
140 149
150 159
9
ID16
ID17
ID18
ID19
160 169
170 179
180 189
190 199
2009.12.9
RED
1
2
3
0
1
2
3
2(0.23) 4(0.43) 6(0.56) 8(0.93) 10Distance(m)
(1.12Diameter(m))
370 93 41 23 15 LUX
15
GREEN
1
2
3
0
1
2
3
2(0.24) 4(0.41) 6(0.69) 8(1.02) 10Distance(m)
(1.02Diameter(m))
740 185 82 46 30 LUX
15
BLUE
1
2
3
0
1
2
3
2(0.23) 4(0.42) 6(0.60) 8(0.88) 10Distance(m)
(1.12Diameter(m))
156 39 17 10
6 LUX
15
RGB
1
2
3
0
1
2
3
2(0.23) 4(0.44) 6(0.68) 8(1.01) 10Distance(m)
(1.07Diameter(m))
1174 293 130 73 47 LUX
15

1.5 SAFETYWARNING
IMPORTANT
ALWAYS READ THEUSER MANUALBEFORE OPERATION.
PLEASE CONFIRM THAT THE POWERSUPPLYSTATED ON THE
PRODUCT IS THESAME ASTHE MAINS POWERSUPPLYIN YOUR
AREA.
This productmust be installedby a qualifiedprofessional.
Always operatethe equipment asdescribed in theuser manual.
Aminimum distance of0.5m must bemaintained between the
equipment and combustiblesurface.
The productmust always beplaced in awell ventilated area.
Always makesure that theequipment is installedsecurely.
DO NOTstand close tothe equipment andstare directly intothe LED
light source.
Always disconnectthe power supplybefore attempting and
maintenance.
Always makesure that thesupporting structure issolid and can
support the combinedweight of theproducts.
The earthwire must alwaysbe connected tothe ground.
Do not touchthe power cablesif your handsare wet.
ATTENTION
This productleft the placeof manufacture inperfect
condition. In orderto maintain thiscondition and forsafe
operation, the usermust always followthe instructions and
safety warnings describedin this usermanual.
Avoidshaking or strongimpacts to anypart of theequipment.
Make sure thatall parts ofthe equipment arekept clean and
free of dust.
Always makesure that thepower connections areconnected
correct and secure.
If there isany malfunction ofthe equipment, contactyour
distributor immediately.
When transferring theproduct, it isadvisable to usethe
original packaging inwhich the productleft the factory.
Shields, lenses orultraviolet screens shallbe changed if
they have becomedamaged to suchan extent thattheir
effectiveness isimpaired.
The lamp(LED) shall bechanged if ithas become damaged
or thermally deformed.
1 PRODUCT(GENERAL) 42009.12.9
4.1 BASICADDRESSING
Connect all of the unitsin series using standard DMX512signal
cable or the IP65 ratedcable provided.
Set theDMX512 addressin the DMX menu.
4.2 CHANNELASSIGNMENT
13
4 USING ADMX512 CONTROLLER
Note: This product havethree DMX512 channel configuration:
STAGE 1 , ARC 1 and ARC 1+D
1
2
0 255
3
4
0 255
0 255
0 255
5
0 10
11 35
36 60
61 85
86 110
111 135
136 160
161 185
186 210
211 215
216 220
221 225
226 230
231 235
236 240
241 245
246 250
251 255
RED 100% / GREENUP / BLUE 0%
RED DOWN / GREEN100% / BLUE 0%
RED 0% / GREEN100% / BLUE UP
RED 0% / GREENDOWN / BLUE 100%
RED UP / GREEN0% / BLUE 100%
RED 100% / GREEN 0%/ BLUE DOWN
RED 100% / GREENUP / BLUE UP
RED DOWN / GREENDOWN / BLUE 100%
WHITE 1: 3200K
WHITE 2: 3400K
WHITE 3: 4200K
WHITE 4: 4900K
WHITE 5: 5600K
WHITE 6: 5900K
WHITE 7: 6500K
WHITE 8: 7200K
WHITE 9: 8500K
MARCO
No function
Ch2 will control the TIME if Ch7 choosecustom01-10
DIMMER
Ch3 will control theFADE if Ch7choose CUSTOM01-10
STAGE 1
BLUE
CHANNEL FUNCTIONVALUE
GREEN
RED
60 10
11 255 Strobe speed
STROBE
No function
4USINGADMX512 CONTROLLER
2009.12.9

2.1 MOUNTING
HANGING
UPRIGHT
The LED PAR can bemounted in anupright or
sitting position usingthe supporting brackets.
The LED PAR can be mounted in a hanging position using the
supporting bracket. The bracket should be secured to the
mounting truss or structure using a standard mounting clamp.
Please note that when hanging the unit a safety cable should
also be used.
@ 220V:40 units maybe connected inseries
@120V: 20units may beconnected in series
The LED MODULE can be mounted at any angle and in any
position. It is possible to further adjust the angle of the LED
MODULE using the two adjustment knobs located on the side of
the fixture.
2.2 POWER CONNECTIONS
5
2 INSTALLATION
Note: As thisfixture's DMX signal cable connection hadbeen changed to
Parallel connection, soif over 30units to beconnected, then aDMX signal
amplifier is needed.
2INSTALLATION
2009.12.9
12
3 DISPLAYPANEL OPERATION 2009.12.9
3.12 SAVE
Only the mainmenu and theAuto-programs submenucan be protected
Repower the unit,it will backto the mainmenu
3.11 PASSWORD
PASSWORD ON/OFF
MENU
PASSWORD
Enter the PASSWORD mode to selectwhether the accesspassword is onor off.
When the fixtureis set asPASS ON , after 30seconds or turnon the fixturenext
time, the fixturewill need anaccess password toenter the displaymenu control.
Note: The factory accesspassword is UP +DOWN +UP +DOWN , then
press ENTER to confirm theaccess.
3.10 SETTINGS
MENU
ID
Reset to Factory?
Up load custom?
Up load custom?
Choose ON /OFF to open or close ID
This function will reset all setting to the original factory setting
Select to upload the custom programs from the current
MASTER unit to the SLAVE units
COLOR is fora ctivate/unactivate thec olorc alibrationf unctions. When
[UC] is selected, the RGB output are adjusted to a standard preset universal
color which balances fixtures from different generations..
The factory default setting is [UC] on.
SETTINGS ID
ON/OFF
Reset to
Factory?
Up load
costom?
COLOR
UC
OFF

2.3 SETTING UPWITHADMX512
CONTROLLER
2.3-1 DMX512ADDRESSING WITHOUT IDADDRESSING
(STAGE1 MODE)
The figure aboveshows a simpleDMX512
layout with thestarting address ofthe first
unit set at1, with thesecond set at10 and
so on... (Notethat when usedin this way,
the CH9 IDfunction must be inactive (CH9=0))
DMX512
CONTROLLER
Connect the DMX512controller to theunits in series.
Each unit has9 DMX channelsso the DMXAddresses shouldincrease by incrementsof
9 (e.g. 1,10,19,28...)
The ID addresshas not beenset so thereforewhen using thecontroller Ch9 must
be inactive (CH9=0 ).
Each DMXAddress may beused as manytimes as required.
Any DMXaddress in therange from 001to 512 maybe used.
2.3-2 DMX512ADDRESSING WITH IDADDRESS(STAGE 1 MODE)
Connect the DMX512controller to theunits in series
Each unit has9DMX channels sothe DMXAddresses should increaseby increments of
9 (e.g. 1,10,19,28...)
Each DMXAddress may beused as manytimes as required.
Any DMXaddress in therange from 001to 512 maybe used.
Each DMX addressmay carry upto 66 separateID addresses.
ID should be setin the menuon each unitin ascending values
(i.e. 1,2,3...)
ID addresses areaccessible from Ch9on the DMX512controller.
Example:
2 INSTALLATION
............
DMX Addr.1 DMX Addr.10 DMX Addr.19
2009.12.9
611
3 DISPLAYPANEL OPERATION
3.6 RUN
RUN
RUN SLAVE DMXEnter to choose or working mode
RUN SLAVE
DMX
MENU
2009.12.9
3.7 PERSON
PERSON STAGE1
ARC1
ARC1+D
MENU
PERSON
PERSON STAGE1 ARC1 ARC1+DEnter and select / / DMX mode
3.8 ID
ID 001~066
MENU
ID
001~066Enter ID and set theID address
3.9 EDIT
EDIT
EDIT custom 1 custom 10
Enter to edit thecustom programs to
Each program has30 steps toedit
Each step allowsa creation ofa scene usingRED,GREEN,BLUE,STRUBE,TIME,
FADE
EDIT custom 1
custom 2
custom 3
custom 4
custom 5
custom 6
custom 7
custom 8
custom 9
custom 10
scene 01
scene 02
scene 03
scene 04
scene 05
scene 06
scene 30
GREN 000~255
BLUE 000~255
STRB 000~020
TIME 000~255
FADE 000~255
Red 000~255
MENU

DMX512
CONTROLLER
Example:
The figure aboveshows a simpleDMX layout
which has usedthree units ateach DMX address.
The three unitshave differentID addresses which
allows the userto collectively controlthe whole
group of unitsat that DMXaddress by setting
CH9 to 0,or to controleach unit independentlyby
first selecting theDMX address andthen by using
Ch9 to locatethe target IDaddress.
2 INSTALLATION
DMX Addr.1
ID Addr.1 DMX Addr.1 ID Addr.2 DMX Addr.1 ID Addr.3 DMX Addr.10 ID Addr.1 DMX Addr.10 ID Addr.2 DMX Addr.10 ID Addr.3
2009.12.9
7
3.3 STATIC
3.4 AUTO
STATIC
RED GREN BLUE STRBSelect / / / to set thevalue
AUTO
Select the target AUTO program and press ENTER
Programs AUTO 1 to AUTO 10 are fully pre-programmedand will notbe
altered
Programs Custom 1 to Custom 10 are fully pre-programmedand can be
edited
10
3 DISPLAYPANEL OPERATION
STATIC GREN 000~255
BLUE 000~255
STRB 000~020
RED 000~255
MENU
AUTO AUTO 1
AUTO 2
AUTO 3
AUTO 4
AUTO 5
AUTO 6
AUTO 7
AUTO 8
AUTO 9
AUTO 10
custom 1
custom 2
custom 3
custom 4
custom 5
custom 6
custom 7
custom 8
custom 9
custom 10
MENU
2009.12.9
3.5 ADDRESS
ADDRESS
ADDRESS 001~512Enter and set theDMX address
ADDRESS 001~512
MENU

3.1 BASIC
3 DISPLAYPANEL OPERATION
DOWN
ENTER UPMENU
MENU scroll through the main menu or exit from the current menu or function
ENTER Enter the currently selected menu or confirm the current function value
UP scroll 'UP' through the menu list or increase the value of the current function
DOWN scroll 'DOWN' through the menu list or decrease the value of the current function
3DISPLAY PANEL OPERATION
2009.12.9
8
3.2 MENU
3 DISPLAYPANEL OPERATION 2009.12.9
9
STATIC
AUTO
ADDRESS
RUN
PASSWORD
PERSON
ID
EDIT
SETTINGS
GREN 000~255
BLUE 000~255
STRB 000~020
RED 000~255
AUTO 1
001~512
SLAVE
ON/OFF
STAGE1
DMX
ARC1
ARC1+D
AUTO 2
AUTO 3
AUTO 4
AUTO 5
AUTO 6
AUTO 7
AUTO 8
AUTO 9
AUTO 10
custom 1
custom 2
custom 3
custom 4
custom 5
custom 6
custom 7
custom 8
custom 9
custom 10
001~066
custom 1
ID
ON/OFF
Reset to
Factory?
Up load
costom?
custom 2
custom 3
custom 4
custom 5
custom 6
custom 7
custom 8
custom 9
custom 10
scene 01
scene 02
scene 03
scene 04
scene 05
scene 06
scene 30
GREN 000~255
BLUE 000~255
STRB 000~020
TIME 000~255
FADE 000~255
RED 000~255
MENU
COLOR
UC
OFF