Expolite tourled 36 cw/ww User manual

USER MANUAL

PART4 USINGA DMX512CONTROLLER....................................10.
4.1--BASIC ADDRESSING.................................................................10.
4.2--CHANNELASSIGNMENT............................................................10.
4.3--BASIC INSTRUCTIONS FORDMX512 OPERATION......................12.
PART3 DISPLAY PANEL OPERATION.........................................7.
3.1--BASIC..........................................................................................7.
3.2--MENU..........................................................................................7.
3.4--DMX512 SETTINGS......................................................................8.
3.5--RUN MODE..................................................................................8.
3.6--PERSONALITY............................................................................8.
3.7--ID ADDRESS...............................................................................9.
3.8--SPECIAL SETTINGS.................................................................... 9.
3.9--A CTIVATETHE PASSWORD ....................................................... 9.
3.10--WHITES SETTING..................................................................... 9.
PART1 PRODUCT(GENERAL)....................................................1.
1.1--PRODUCT INTRODUCTION.........................................................1.
1.2--PRODUCT FEATURES.................................................................1.
1.3--TECHNICAL SPECIFICATIONS.....................................................2.
1.4--PHOTOMETRICDATA..................................................................3.
1.5--SAFETY WARNING......................................................................3.
PART2 INSTALLATION...............................................................4.
2.1--MOUNTING...................................................................................4.
2.3--SETTING UPWITHA DMX512 CONTROLLER.................................5.
2.3-1--DMX512ADDRESSING WITHOUTID ADDRESSING......................................5.
2.3-2--DMX512 ADDRESSING WITHID ADDRESS..................................................5.
2.2--POWER CONNECTION................................................................. 4.
3.3--EDIT STATICCOLOUR.................................................................8.
PART5 APPENDIX......................................................................13.
5.1--TROUBLE SHOOTING...............................................................13.
5.2--MAINTENANCE........................................................................ 14.
ABLE OF CONTENTS
T

* Dimmer0-100%
* Strobe
* IP65protection rating
* LEDdisplay
* Display control'lock-out'
* DirectDMX512 input
* Independent IDaddress
* Lightweightaluminium casing
* Differentwhite colorssetting
* 'Over-heat'protection (showing HT )
1.1 PRODUCTINTRODUCTION
1 PRODUCT(GENERAL) 12008.9.19
1PRODUCT (GENERAL)
This product is designed for indoor or outdoor use. Suitable applications include wash or
effect lighting for architectural, stage or nightclub applications. This product can also be
installed for use in signage and advertising using the dynamic functions available with
DMX512 control. Direct input of DMX512 signal allows the units to be controlled from any
DMX512 controller. This product can be operated as a single unit or in multiple units for
large applications.
1.2 PRODUCTFEATURES
LED FIXTURE

1.3 TECHNICALSPECIFICATIONS
LED MODULE
Dimensions
LED MODULE:
Voltage
Rated Power
IP65 protection rating
36pcs (18 xCool white /18 x Warmwhite)
Weight
LED/Unit
Output/LED
Cooling
IP
1W
Direct air convection
243 x 200x 245mm
4Kg
100~240V...50/60Hz
60W
1 PRODUCT(GENERAL) 2
Environment Temperature -20 ~40
2008.9.19

1.4 PHOTOMETRICDATA
1 PRODUCT(GENERAL) 32008.9.19
1.5 SAFETYWARNING
IMPORTANT
ALWAYSREAD THEUSER MANUALBEFORE OPERATION.
PLEASE CONFIRMTHATTHE POWERSUPPLYSTATED ONTHE
PRODUCT ISTHE SAMEAS THEMAINS POWERSUPPLYIN YOUR
AREA.
This productmust beinstalled bya qualifiedprofessional.
Always operatethe equipmentas describedin theuser manual.
A minimum distance of 0.5m must be maintained between the equipment and
combustible surface.
The productmust alwaysbe placedin awell ventilatedarea.
Always makesure thatthe equipmentis installedsecurely.
DO NOT stand close to the equipment and stare directly into the LED light
source.
Always disconnectthe powersupply beforeattempting andmaintenance.
Always make sure that the supporting structure is solid and can support the
combined weight ofthe products.
The earthwire mustalways beconnected tothe ground.
Do not touchthe power cablesif your handsare wet.
ATTENTION
This product leftthe place ofmanufacture in perfectcondition. In orderto
maintain thiscondition andfor safeoperation, theuser mustalways followthe
instructions andsafety warningsdescribed inthis usermanual.
Avoid shakingor strong impactsto any partof the equipment.
Make sure thatall parts ofthe equipment arekept clean andfree of dust.
Always makesure thatthe powerconnections areconnected correctand
secure.
If thereis anymalfunction ofthe equipment,contact yourdistributor
immediately.
When transferringthe product,it isadvisable touse theoriginal packagingin
which the productleft thefactory.
Shields, lenses orultraviolet screens shallbe changed ifthey have become
damaged tosuch anextent thattheir effectivenessis impaired.
The lamp(LED) shallbe changedif ithas becomedamaged orthermally
deformed.
COOL WHITE
1
2
3
0
1
2
3
246810Distance(m)
3128 847 388 226.8 149.4 LUX
15
COOL WHITE+WARM WHITE
1
2
3
0
1
2
3
246810Distance(m)
1781 466 216 128 87 LUX
15
1
2
3
0
1
2
3
246810Distance(m)
4951 1320 602 350.7 236.7 LUX
15
WARM WHITE

@ 220V:50 unitsmay beconnected inseries
@120V: 25units maybe connectedin series
The LED MODULEcan be mountedat any angleand in any
position. It ispossible to furtheradjust the angleof the LED
MODULE using thetwo adjustment knobslocated on theside of
the fixture.
2.2 POWER CONNECTIONS
4
2 INSTALLATION
Note: As thisfixture's DMX signal cable connection isParallel connection, soif over 20units
to beconnected, thena DMXsignal amplifieris needed.
2008.9.19
2INSTALLATION
2.1 MOUNTING
HANGING
UPRIGHT
The LED PAR can be mounted in an upright or
sitting position usingthe supporting brackets.
The LED PAR can be mounted in a hanging position using
the supporting bracket. The bracketshould be securedto
the mountingtruss or structure usinga standard mounting
clamp. Please note that when hanging the unit a safety
cable shouldalso beused.

2.3 SETTING UPWITHADMX512
CONTROLLER
2.3-1 DMX512ADDRESSING WITHOUT IDADDRESSING
(STUDIO 2MODE)
The figureabove showsa simpleDMX512
layout with thestarting address ofthe first
unit setat 1,with thesecond setat 7and
so on... (Note thatwhen usedin thisway,
the CH6 IDfunction must be inactive (CH6=0))
DMX512
CONTROLLER
Connect the DMX512controller to theunits in series.
Each unithas 6DMX channelsso theDMX Addresses shouldincrease byincrements of
6 (e.g. 1,7,13,19...)
The ID addresshas not beenset so therefore when usingthe controller CH8must
be inactive (CH6=0 ).
It isalso possibleto deactivateID addressselecting ID OFF from the Settings menu.
on the fixture
Each DMXAddressmay beused asmany timesas required.
Any DMXaddress inthe rangefrom 001to 512may beused.
2.3-2 DMX512ADDRESSING WITH IDADDRESS(STUDIO 2MODE)
Connect theDMX512 controllerto theunits inseries
Each unithas 6DMX channelsso theDMX Addresses shouldincrease byincrements of
6 (e.g. 1,7,13,19...)
Each DMXAddressmay beused asmany timesas required.
Any DMXaddress inthe rangefrom 001to 512may beused.
Each DMX addressmay carry upto 66 separateID addresses.
ID should beset inthe menuon eachunit inascending values
(i.e. 1,2,3...)
ID On should beset inthe Settings menu on eachunit.
ID addressesare accessiblefrom CH6on theDMX512 controller.
Example:
5
2 INSTALLATION
............
DMX Addr.1 DMX Addr.7 DMX Addr.13
2008.9.19

6
2 INSTALLATION 2008.9.19
DMX512
CONTROLLER
Example:
The figureabove showsa simpleDMX layout
which has usedthree units ateach DMX address.
The three unitshave differentID addresses which
allows theuser tocollectively controlthe whole
group ofunits atthat DMXaddress bysetting
CH6 to0, orto controleach unitindependently by
first selectingthe DMXaddress andthen byusing
Ch6 to locatethe target IDaddress.
............
DMX Addr.1
ID Addr.1 DMX Addr.1 ID Addr.2 DMX Addr.1 ID Addr.3 DMX Addr.7 ID Addr.1 DMX Addr.7 ID Addr.2 DMX Addr.7 ID Addr.3

3 DISPLAY PANEL OPERATION 2008.9.19
3DISPLAY PANEL OPERATION
7
3.2 MENU
3.1 BASIC
The LED fixtureis mounted witha LCD displayand 4 controlbuttons.
MENU SET UP DOWN
enter thecurrently selectedmenu orconfirm thecurrent functionvalue
scroll 'UP' through the menulist or increase the valueof the current function
scroll'DOWN' throughthe menulist ordecrease the valueof thecurrent function
scroll throughthe mainmenu orreturn tothe mainmenu
UPSET DOWN
MENU
POWER OUTPOWER IN
DMX IN DMX OUT
MODE COOL
WARM
STRb
STAI
C.(0~255)
W.(0~255)
d(001~512)
dMX
RUN dMX
SLAV
Id
I(001~066)
SET UPLd
IdON
PASS
ON
OFF
SENd ENd
PASS ON
OFF
CALI
W1
W2
W8
C.(0~255)
W.(0~255)
dIMM S.(0~20)
d.(0~255)
PERS
CWd
STU1
STU2
CW
REST PASS REST

3 DISPLAY PANEL OPERATION 2008.9.19
8
3.3 EDITSTATIC COLOUR
STATIC COLOUR
Combine COOL , WARM ,and Dimmer to createwhites withdifferent
color temperature
Set thevalue ofthe Strobe (0-20Hz)
3.4 DMX512 SETTINGS
DMX
Enter the DMX mode to setthe DMXADDRESS.
RUN MODE
Enter the RUN MODE mode toset workingmode.
DMX mode is forusing the DMX512controller to controlthe fixtures.
SLAVE mode isfor Master-- Slaveoperation, orcontrolled fixtureby
Pix-controller.
Note: When fixturesare underAutoprogram operation,the RUN MODE does no
works.
3.5 RUN MODE
3.6 PERSONALITY
PERSONALITY
Enter the PERSONALITY mode toselect DMXmode: CW , CW+D ,
STUDIO 1 ,or STUDIO 2 .
d(001~512)
dMX
MODE
RUN dMX
SLAV
MODE
MODE COOL
WARM
STRb
STAI
C.(0~255)
W.(0~255)
dIMM S.(0~20)
d.(0~255)
PERS
CWd
STU1
STU2
CW
MODE

3 DISPLAY PANEL OPERATION 2008.9.19
9
3.7 IDADDRESS
ID
Enter the ID mode to setthe IDADDRESS.
3.8 SPECIALSETTINGS
SETTING
Select Upload to upload thecustom programs fromthe current MASTERunit to
the SLAVE units.
In orderto activatethe uploadfunction thepassword mustbe entered.
Password isthe sameas themain accesspassword.
When uploading theMASTER and SLAVE units willbe full on..
If anerror occurswhen uploading the MASTERand/or SLAVE unitswill display
Warm White..
On successful uploadingof the customprograms the MASTERand SLAVE units
will displayCool White.
In order toreset custom modesto default valuesselect PESET Parameter .
Enter ID ON/OFF in orderto allow/disallowID addressfunction fromthe
DMX512 controller.
3.9 ACTIVATE THEPASSWORD
KEYLOCK
Enter the KEYLOCK mode to selectwhether the accesspassword is onor off.
In order toenter access passwordit is necessaryto firstpress SET .
Accesspassword is UP +DOWN +UP +DOWN .
CALIB
Enter the CALIB to select white colorof differentcolor temperature.
There are8 pre-programmedWhite colors can beedited
by using Cool white &Warm white .
3.10 WHITES SETTING
PASS ON
OFF
MODE
SET UPLd
IdON
PASS
ON
OFF
SENd ENd
REST PASS REST
MODE
Id
I(001~066)
MODE
CALI
W1
W2
W8
C.(0~255)
W.(0~255)
MODE

Note: This product havefour DMX512 channel configuration: CW , CW+D ,
STUDIO 1 and STUDIO 2
4.1 BASICADDRESSING
Connect all of the unitsin series using standard DMX512signal cable or the IP65rated cable
provided.
Set theDMX512 addressin the DMX menu.
It ispossible tohave thesame DMXaddress orindependent addressesfor eachfixture.
4.2 CHANNELASSIGNMENT
10
4 USINGA DMX512CONTROLLER 2008.9.19
4USING ADMX512 CONTROLLER
CW
1
2
0 255
CHANNEL FUNCTIONVALUE
0 255 WARM WHITE
COOL WHITE
CW+D
1
2
0 255
CHANNEL FUNCTIONVALUE
3
0 255
0 255
MASTER DIMMER
STUDIO 1
1
2
0 255
CHANNEL FUNCTIONVALUE
0 255
MASTER DIMMER
SAME AS STUDIO 2 CH4
WARM WHITE
COOL WHITE

STUDIO 2
1
2
0 255
CHANNEL FUNCTIONVALUE
3
0 255
0 255
NO FUNCTION
4
11
4 USINGA DMX512CONTROLLER 2008.9.19
MASTER DIMMER
0 10
11
41
71
101
131
161
191
40
70
100
130
160
190
220
221 255
WHITE 1: 2800K
WHITE 2: 3000K
WHITE 3: 3200K
WHITE 4: 3400K
WHITE 5: 4200K
WHITE 6: 4900K
WHITE 7: 5600K
WHITE 8: 5900K
DIFFERENT WHITES
NO FUNCTION
0 9
10 255 1~20Hz
STROBE
5
ID ADDRESS
ID1~ID66
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
ID9
ID10
ID11
ID12
ID13
0 9
10 19
20 29
30 39
40 49
50 59
60 69
70 79
80 89
90 99
100 109
110 119
120 129
130 139
ID14
ID15
140 149
150 159
ID21210
ID66255
ID20
200 209
ID18
ID16
ID17
160 169
170 179
180 189
ID19190 199
WARM WHITE
COOL WHITE
6

4.3 BASIC INSTRUCTIONS FOR DMX512
OPERATION (STUDIO 2)
MASTER DIMMER
CH1 controlsthe intensityof thecurrently projectedcolor
When theslider isat thehighest position(255) theintensity ofthe outputis themaximum
SELECTION
CH2 and CH3 control the intensityratio of eachof the LEDs.
When the slideris atthe highest position(255) the intensityof thecolor is themaximum.
CH2 and CH3 can becombined togetherto createwhites withdifferent colortemperature.
STROBE
CH 5controls thestrobe ofCH1 toCH4
CH5 haspriority overCH2, CH3& CH4.
DIFFERENT WHITES
Ch4 allow user toselect 8whites withdifferent colortemperature.
The 8whites aretake fromthe CALIB on Displaypanel.
ID ADDRESSSELECTION
CH6 is usedto select thetarget ID address.
Each independent DMXaddress may haveupto 66 independentID addresses.
An IDaddress of 0will activate allID address locations.
COOL WHITE& WARM WHITE COOL WHITE& WARMWHITE
12
4 USINGA DMX512CONTROLLER 2008.9.19

No display
SITUATION CAUSE ACTION
5.1 TROUBLE SHOOTING
1) No powerinput
2) Power connectionerror
3) Display damaged
4) Display boardIC error or power input
connection error or two boardconnection
error
1) Check powersupply
2) Check powerconnection
3) Replace display
4) Check theIC and allthe connections
Display normal,
but no response
from buttons
1) Buttons damaged
2) Main PCBdamaged 1)Replace buttons 2) Replace MainPCB
1) Signal Cableerror
2) Signal conncetionerror
3) The inputsignal IC damaged4 DMX
address error
Display normal,
but no response
from buttons
1) Check allsignal Cables
2) Check allsignal conncetions
3) Check theinput signal IC
4) Check DMXaddress
1) Check LEDsjoining
2) Check lensinstalling
1) LED notjoining well
2) Lens notinstalling well
Color mixing
uneven,with splash
1) LED damaged
2) LED damagedor Main PCB
LEDs of thesame
color are notlit 1) Replace LEDs
2) Replace damagedLED or MainPCB
1) Replace savingIC1) Saving ICdamaged
Manual and program
can not save or
display error
13
5 APPENDIX 2008.9.19
5APPENDIX

5.2 MAINTENANCE
14
5 APPENDIX 2008.9.19
Version 1.0
No
1
2
3
4
5
6
7
8
9
10
ITEM
Gel holder
Upper cover
Glass plate
LED heat-transfer plate
Power supply
Display board
Casing
Driver board
Secondary support
Main support