Expolite tourspot 60 User manual

USER
USER
USER
USER MANUAL
MANUAL
MANUAL
MANUAL
60W
60W
60W
60W MOVING
MOVING
MOVING
MOVING HEAD
HEAD
HEAD
HEAD LED
LED
LED
LED
(1 2 CHANNELS)
Please read over this manual be f ore operating the light
Professional
Professional
Professional
Professional Stage
Stage
Stage
Stage Lighting
Lighting
Lighting
Lighting

1
CONTENT
CONTENT
CONTENT
CONTENT
Content ……………………………………………………………… .. …… ........................ 1
Attention ………………………………………………………… .. ………… ...... … ........... 2
Structure ……………………………………………………… .. ………… ........ … ............. 3
Technical parameter ……………………………………………………… ......... … ............ 3
D MX 512 Channels …………………………………………… ......... … ............................
4-6
Disgital display function ……………………… .. ………… ............ … ...... … ...... … .............
7-8
Install the fixture ………………………………………… ..... ……… ... ...... … ...... … ..........
9
Power supply mains ………………………………………… .. ………… .. ...... … ................
1 0
Signal input ……………………………………………………… .. … … ...... …… .. ............
1 1
Rigging ( optional) ……………………………………………… .. … … ...... …… .. ...............
1 2
Maintenance ……………………………………………………………… . … ...... .. .............
1 2
Cleaning of lens system …………………………………… .. ………… ...... … ...... … ..........
1 2
Safety in formation ………………………………………… .. ………… ...... … ...... … .........
1 2
A larm ………………………………………………………………………… . ...... … .........
1 3
S olutions to problems ……………………………………… .. ……… ... ......... … ...... … .......
1 3

2
A
A
A
A TTENTION:
TTENTION:
TTENTION:
TTENTION:
Thank you very much to choose our light! EXPOLITE TourSpot 60 is powerful in
functions with “CE ”Standard. I t has been tested through frequent practice in deferent
cases , a nd well recognized by professional designers in the filed of stage light. It fully
shows the modern times light characteristic with good performance, it can be used in
all kinds of scenes with need high quality lighting.
P lease read this manual carefully before powering or installing the fixture, follow the
safety precautions listed below and observe all warnings in this manual.
War n ing : Always disconnect from mains supply before replacing the lamp, or not, it
will burn the light.
1. Disconnect the fixture from AC power before removing or installing the lamp,
fuses , or any part, and when not in using
2. Always make the fixture connected to the ground electrically.
3. Please stop using when it is very hard to use , and check the problem with our
agent or factory.
4. If lamp on/off by controller please pays attention to the voltage depressed when
open a lot of light in one time.
5. Using Electromagnetic ballast , the second time to open the light should be after
15 minutes from the first time.
6. Don ’ t expose the fixture to rain or moisture.

3
STRUCTURE
STRUCTURE
STRUCTURE
STRUCTURE
1、Aperture
2、Housing
3、Arm
4、Cover
5、Digital screen
EXPOLITE TourSpot 60 moving head is a kind of very powerful computer light and it has gained a very popular
approval by the professional light designer after numerous use and strict test on its stability and has already
become one of the most successful computer light; it can produce strong and impressive bright light and be
suitable for any spot where the clear cast is required; it meets CE standards.
TECHNICAL
TECHNICAL
TECHNICAL
TECHNICAL PARAMETER:
PARAMETER:
PARAMETER:
PARAMETER:
VOLTAGE
VOLTAGE
VOLTAGE
VOLTAGE :
:
:
:AC 2 2 0V 50 / 60Hz
L
L
L
L IGHT
IGHT
IGHT
IGHT SOURCE
SOURCE
SOURCE
SOURCE :
:
:
:6 0 W LED
POWER
POWER
POWER
POWER CONSUMPTION:
CONSUMPTION:
CONSUMPTION:
CONSUMPTION: 15 0 W
BEAM
BEAM
BEAM
BEAM ANGLE:
ANGLE:
ANGLE:
ANGLE: 18 °
RATED
RATED
RATED
RATED LIFE:
LIFE:
LIFE:
LIFE: 60,000~100,000hours
1
1
1
1 COLOR
COLOR
COLOR
COLOR WHEEL:
WHEEL:
WHEEL:
WHEEL: 6 colors+open, half color effect,
bi-directional rainbow effect at variable speed
1
1
1
1 ROTATING
ROTATING
ROTATING
ROTATING GOBO
GOBO
GOBO
GOBO WHEEL:
WHEEL:
WHEEL:
WHEEL: 7 rotating gobos+open, bi-directionally rotating at variable speed
1
1
1
1 PRISM
PRISM
PRISM
PRISM WHEEL:
WHEEL:
WHEEL:
WHEEL: 3-facet prism, bi-directionally rotating, at variable speed
FOCUS:
FOCUS:
FOCUS:
FOCUS: Linearly adjustable
DIMMER:
DIMMER:
DIMMER:
DIMMER: 0~100% linearly adjustable
STROBE:
STROBE:
STROBE:
STROBE: 0~20 flash per second, speed adjustable
PAN
PAN
PAN
PAN AND
AND
AND
AND TILT:
TILT:
TILT:
TILT: Smooth, automatic Pan&Tilt positioncorrection, speed adjustable
RANGE:
RANGE:
RANGE:
RANGE: Pan-540 ° , Tilt-270 ° (16-bit)
VECTOR
VECTOR
VECTOR
VECTOR MODE:
MODE:
MODE:
MODE: Color+GOBO+Prism+XY Vector
CONTROL
CONTROL
CONTROL
CONTROL PROTOCOL:
PROTOCOL:
PROTOCOL:
PROTOCOL: DMX 512, 3 pin interface
CHANNELS:
CHANNELS:
CHANNELS:
CHANNELS: 12
DISPLAY:
DISPLAY:
DISPLAY:
DISPLAY: LED, the words can be upside down
PROTECT
PROTECT
PROTECT
PROTECT GRADE:
GRADE:
GRADE:
GRADE: IP20, overheating & overvoltage protection
NET
NET
NET
NET WEIGHT:
WEIGHT:
WEIGHT:
WEIGHT: 8.5 KG
GROSS
GROSS
GROSS
GROSS WEIGHT:
WEIGHT:
WEIGHT:
WEIGHT: 11 KG
FIXTURE
FIXTURE
FIXTURE
FIXTURE DIMENSION:
DIMENSION:
DIMENSION:
DIMENSION: L325*W250*H401(mm)
PACKING
PACKING
PACKING
PACKING DIMENSION:
DIMENSION:
DIMENSION:
DIMENSION: L 405 *W 385 *H4 35 (mm)

4
DMX
DMX
DMX
DMX 512
512
512
512 CHANNELS
CHANNELS
CHANNELS
CHANNELS :
:
:
:
CHANNEL 1: SHUTTER+STROBE+RESET
CHANNEL 2: DIMMER
CHANNEL 3: COLOR WHEEL
CHANNEL 4: ROTA TING GOBO WHEEL
CHANNEL 5: GOBO ROTA TION
CHANNEL 6: FOCUS
CHANNEL 7: PRISM+PRISM ROTA TING
CHANNEL 8: PAN
CHANNEL 9: PAN FINE
CHANNEL 10: TILT
CHANNEL 11: TILT FINE
CHANNEL 12: PAN & TILT SPEED + VECTOR MODE
CHANNEL 1 IRIS
DMX512 signal 0-255 range Function
0- 10 Shutter off
11-39 Shutter on
40-240 Strobe, slow to fast
241-245 Shutter on
246-250 Reset
251-255 Shutter on
CHANNEL 2 D I MM ER
DMX512 signal 0-255 range Function
0 - 255 D ark to Bright
CHANNEL 3 COLOR WHEEL
DMX512 signal 0-255 range Function
0 - 1 8 Open
1 9 - 3 7 Color 1
38-56 Color 2
57-75 Color 3
76-94 Color 4
95-113 Color 5
114-127 Color 6
128-191 Rainbow effect, c lockwise , fast to slow

5
192-255 Rainbow effect, a nticlockwise , slow to fast
CHANNEL 4 ROTA TING GOBO WHEEL
DMX512 signal 0-255 range Function
0 - 1 5 Open
1 6 - 3 1 Gobo 1
3 2 - 47 Gobo 2
48 - 63 Gobo 3
64-79 Gobo 4
80-95 Gobo 5
96-111 Gobo 6
112-127 Gobo 7
128-191 Rainbow effect, c lockwise , fast to slow
192-255 Rainbow effect, a nticlockwise , slow to fast
CHANNEL 5 GOBO ROTA TING
DMX512 signal 0-255 range Function
0 - 127 Rotating Angle
128-191 Clockwise Rotating, slow to fast
192-255 Anticlockwise Rotating, slow to fast
CHANNEL 6 FOCUS
DMX512 signal 0-255 range Function
0-255 Focus
CHANNEL 7 PRISM+PRISM ROTA TING
DMX512 signal 0-255 range Function
0- 4 No Prism
5-19 Prism
20-139 Prism Angle Adjustment
140-197 Clockwise Rotating, fast to slow
198-255 Anticlockwise Rotating, slow to fast
CHANNEL 8 PAN
DMX512 signal 0-255 range Function
0-255
0-450 °
CHANNEL 9 PAN FINE
DMX512 signal 0-255 range Function
0 -255
0-2.1 °
CHANNEL 1 0 TILT
DMX512 signal 0-255 range Function

6
0-255
0-270 °
CHANNEL 1 1 TILT FINE
DMX512 signal 0-255 range Function
0 - 255
0-1.0 °
CHANNEL 1 2 PAN & TILT SPEED + VECTOR MODE
DMX512 signal 0-255 range Function
0- 251 Fast to slow
25 2- 255 Vector mode

7

8

9
INSTALL
INSTALL
INSTALL
INSTALL THE
THE
THE
THE FIXTURE
FIXTURE
FIXTURE
FIXTURE
1. Make sure that the point of fixing is stable before positioning the light, It must bear more than
10 multiple of the light weight
2. Use two special M10 bolts to fix the fixed-screw, which is in the projector ’ s soleplate, ensure
projector can ’ t fall. And, must use rope to tie the projector ’ s handle and other fixing-points
when you fix them.
3. when positioning the projector, the distance between the objects that beam hi and the lens of
projector should keep more than 1meter, and the minimum distance from the surface of
projector to any flammable material should be at least 0.5meters.In order to ensure the light
working normally and stably, the ambient temperature must not exceed 35 °

10
Power
Power
Power
Power Supply
Supply
Supply
Supply Mains
Mains
Mains
Mains
Use the provided plug to connect the main power to the projector paying attention to the voltage and frequency
marked on the panel of the projector. It is recommended that each projector be supplied separately so that they
may be individually switched on and off.
Important
Important
Important
Important
It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant
standards. Power consumption of this projector is 15 0W@220V .
Watchdog
Watchdog
Watchdog
Watchdog system
system
system
system
When the projector is switched on the electronics performing a reset, this function moves the head to an extreme
limit point and rotates the internal Colour and gobo wheels thus allowing the microprocessor control system to
register the positions of all motor under its control. When the lamp strikes and fires up it can create some noise
within the projector that has the potential to disturb the microprocessors. This projector is fitted with an
electronic watchdog system that monitors the microprocessor and will initiate a reset if the functioning of the
microprocessor has been disturbed. This system ensures that the reset is performed successfully and once
completed the projector is ready to receive control instruction and operate without problem.
Delivery
Delivery
Delivery
Delivery
Notice ：Open delivery lock before operation.
This is transported in carton .
Things as follows are enclosed ：
User manual
One additional fixtures
2.5 meters signal line
One safety string
Package
Package
Package
Package
1、Shut off the power supply and cool it.
2、Put the light at the bottom of the case. Do not closethe case with heavy strike.

11
Signal
Signal
Signal
Signal Input
Input
Input
Input
Connecting to the DMX512 control signal line
In case of disturbance during transmission of control signal , please use high-quality connecting line,
and insert one terminal into the output socket of the last equipment for signal connecting. (solder
one 1/4W120 ohm resistance to 3-pin canon plug on pin 2, pin 3
Connecting to the DMX512 control signal line
Please use high-quality line for connecting in case of disturbance.

12
Rigging
Rigging
Rigging
Rigging （O
O
O
O ptional
ptional
ptional
ptional ）
This equipment can be positioned and fixed by clamp in every direction of the stage. Locking system makes it
easy to fasten to the bracket.
Attention! Two clamps are needed to fix the equipment. Every clamp is locked by fastener of 1/4 kind. Fastener
can only be locked clockwise.
Attention! Fasten a safety string to the additional hole of side aluminum piece. The secondary accessory can not
hang on the delivery handle. Nip the equipment on bracket.
1, Check if rigging clamp (not including the one inside) damaged or not. If stand ten times weight as the
equipment. Make sure the architecture can stand ten times weight as all the equipments, clamps, wirings and other
additional fixtures.
2, Screws for clamping must be fixed firmly. Take one M12 screw (Grade 8.8 or higher) to clamp bracket, and
then screw the nuts.
3, Level the two hanging points at the bottom of clamp. Insert fastener to the bottom, lock the two levers by 1/4
rotating clockwise; then install another clamp.
4 Install on safety string which stands at least ten times weight as equipment. Terminal of the accessory is
designed for clamps.
5 Make sure pan/tilt lock opened or not. Keep the distance more than 1 M from equipment to flammable material
or lighting source.
Maintenance
Maintenance
Maintenance
Maintenance
Cleaning
Cleaning
Cleaning
Cleaning of
of
of
of lens
lens
lens
lens system
system
system
system
Wash exterior and interior optical mirrors to enhance the brightness in regular time, especially when
equipment used in messy surroundings. Use mirror cleanser (or alcohol) to wash exterior mirrors in every
15/20 days, 40/60 days for interior focusing prism/reflector.
Saf
Saf
Saf
Saf e
e
e
e ty
ty
ty
ty information
information
information
information
Do not separate the light personally.
Prevent liquid, water and metal into the equipment.
The
The
The
The equipment
equipment
equipment
equipment not
not
not
not fit
fit
fit
fit for
for
for
for cases
cases
cases
cases below:
below:
below:
below:
◆Relative humidity is too high.
Shake and hit
Room temperature is above 40 degree or below 0 degree.
Relative temperature is below 30 degree or above 80 degree.
Notice
Notice
Notice
Notice ：
In case of serious problems, stop using the equipment, and refer it to the agent or factory for checking.
Do not separate the equipment; there are no accessories for replacing use in it.

13
Who to check this equipment must be well qualified.
If the functional controller is used to ignite light, be cautious that the voltage will fall down immediately
when many lamps are lighted. The solution to this is lighting the lamps in every five seconds one by one.
When magnetic ballast is used, make sure it is five minutes after the bulb is cooled when relight the lamps.
(Electronic ballast can relight by heat)
When pull out the line of power supply, do grip the insulated housing of the plug, do not draw the line
directly.
Alarm
Alarm
Alarm
Alarm ：
Replace the housing, lens and ultraviolet radiation when visible damage takes place, such as cracks.
Replace the lamp when damage happens to it or its maximum life is used up.
Shut off the power supply when replace lamp, safety box, and any other accessories and when it does not
work.
Keep the ground switch connected to ground.
Power supply must meet the local standard on architecture and electric signal with overload protection and
connect to earth.
Do not make light beam shine on skin, do not look at the light source directly.
Prevent short circuit happening to temperature control switch and safety box. When replace defective fuse,
choose approved new fuse of the same type.
Keep the distance more than 1 M from equipment to flammable material (such as cloth, wood, paper).
Keep the distance 0.1 M from fan to vent.
When housing of equipment feels very hot, cool it for 5 minutes before operation.
Advise you to choose accessories produced by us when install and replace.
Whenever install or move equipment, set an alarm to prevent others entering job site.
Do not put your hand between side arm and light structure when light working. (shown in picture 1 by arrow)
Keep the optical system clean. Make the maintenance according to this manual when use in messy and dusty
environment
Luminous flux will decrease once the mirror gets covered by fatness or dust .
Solutions
Solutions
Solutions
Solutions to
to
to
to problems
problems
problems
problems
Phenomenon
Phenomenon
Phenomenon
Phenomenon o
o
o
o f
f
f
f power
power
power
power supply
supply
supply
supply
◆Lamp does not light, motor does not work itself.
When reset, indicator light of On/Off does not light.
◆Lamp lights, reset, but one of the protocols out of control.
Lamp not in stable control for lighting.
Light spot not bright enough.
Lamp lights, then black out, and lights again in a while.
Causes
Causes
Causes
Causes ：
Power supply not in normal state, not well connected, the fuse breaks up.
Control line not connected, or connected not to the right address code, please check the address code.
Voltage is too low, lamp close to using up
◆Lamp clos e to using up, optical mirror not clean.
Overheat ing protection, please check if cooling system is blocked or not.