Extech Instruments SP505 User manual

USER MANUAL
Solar Power Meter
Model SP505
Additional User Manual Translations available at www.extech.com

SP505-en-GB_V1.1 10/18
2
Introduction
Thank you for selecting the Extech Model SP505 Solar Power Meter. This device measures the
power of solar radiation. Use the SP505 to measure the effectiveness of solar film, measure solar
radiation, check solar insulated windows, check headlight intensity, and find the optimal
incidence angle for solar panels and solar water heaters. This device is shipped fully tested and
calibrated and, with proper use, will provide years of reliable service. Please visit our website
(www.extech.com) to check for the latest version and translations of this User Manual, and for
Customer Support.
Safety
Please read the entire User Manual before operating this device. Use the meter only as specified
and do not attempt to service or open the meter housing. Do not allow children to handle the
meter. Please dispose of batteries and meter responsibly and in accordance with all applicable
laws and regulations. Do not look directly into the sun, damage to your eyes can result.
Meter Description
1. Solar Light Sensor
2. LCD
3. Unit button
4. Zero button
5. Power ON-OFF button
6. Range button
7. Hold button
Note: Battery compartment and tripod mount are located on the
back of the meter
LCD Description
1. Data Hold icon
2. Zero calibration mode
3. Battery status
4. Unit of measure (W/m2or BTU (ft2*h))
5. Measurement display

SP505-en-GB_V1.1 10/18
3
Operation
Power the Meter
Press the button to turn the meter ON/OFF. If the meter display does not switch ON, please
check the batteries (2 x 1.5V ‘AAA’) in the rear compartment. The meter has an APO feature
where the meter automatically switches off after 10 minutes of inactivity.
Zero the Sensor
Cover the sensor, and press the button to zero the display before use.
Range Selection
Short press the button to toggle the range of the meter. The meter display range toggles
between 0.1 and 1 unit resolution.
Unit Selection
Short press the button to toggle the units between W/cm2 and BTU (ft2*h); the lower
display area will show the selected units.
Data Hold
Short press the button to freeze or unfreeze a reading on the display.
Testing Solar Power
With the meter ON, zero the display and then point the sensor (top of meter) toward the sun
and read the displayed power measurement. A display of ‘OL’ indicates that the measured
power is beyond the range of the meter.
Other Application Examples
Automobile Headlight Measurements
1. Turn on the headlights and short press the power button to power the meter.
2. Face the sensor (top of meter) toward one headlight and then the other, recording each
reading.
3. Turn the high beams on and measure both headlights again, recording the readings.
4. Retain the recorded readings with the vehicle for reference.
5. Short press the power button to power OFF the meter.
Measuring the Solar Insulation of Windows
Use the meter to test the solar film of car windows or the heat efficiency of windows in
residential or commercial properties.
1. Turn on the meter and zero the display before taking a measurement.
2. With the window closed, aim the sensor toward the sun and record the reading.
3. Open the window and aim the device toward the sun, recording the reading.
4. Compare the two values to determine the heat efficiency of the window. Test the windows
at least once a year to monitor efficiency.

SP505-en-GB_V1.1 10/18
4
Maintenance
Battery Replacement
1. Power OFF the meter.
2. Slide the battery compartment cover off in a downward motion.
3. Replace the two (2) ‘AAA’ 1.5V batteries observing correct polarity. Secure the
compartment cover before using the meter.
Safety: Please dispose of batteries responsibly, never dispose of batteries in a fire, batteries may explode or
leak. If the meter is to be stored for 60 days or more, remove the batteries and store them separately.
Never dispose of used batteries or rechargeable batteries in household waste.
As consumers, users are legally required to take used batteries to appropriate collection sites, the
retail store where the batteries were purchased, or wherever batteries are sold.
Disposal: Do not dispose of this instrument in household waste. The user is obligated to take end-
of-life devices to a designated collection point for the disposal of electrical and electronic
equipment.
Cleaning and Storage
Clean the sensor (top of meter) occasionally with a soft, dry cloth.
Periodically wipe the case with a damp cloth and mild detergent; do not use abrasives or
solvents.
Store the meter in the supplied pouch.
Remove the batteries if the meter is to be stored for more than 60 days.

SP505-en-GB_V1.1 10/18
5
Specifications
Display
3 ¾ digit LCD display (3999 counts)
Measurements
Solar Radiation Power
Sampling Rate
Approximately 0.25 seconds
Over-range Display
“OL“
Tripod mount
On rear panel
Power
2 x 1.5V ‘AAA’batteries
Battery life
Approx. 50 hours
Automatic power off (APO)
After approx. 10 minutes of inactivity
Operating Temperature/Humidity
5 to 40oC (41 to 104oF) / 80% RH max
Operating Altitude
2000 meters (7000 ft.) maximum
Storage Temperature/Humidity
-10 to 60oC (14 to 140oF) / 70% RH max
Dimensions/Weight
108 x 48 x 23mm (4.3 x 1.9 x 0.9”) /80g (2.8oz)
Safety
For indoor use only. EMC: EN61326 (1997), A1 (1998), A2 (2001);
Pollution degree 2
Electrical Specifications (25±5°C)
Solar Power
Unit
Range
Resolution
Accuracy*
W/m2
0 to 3999
0.1
±10 W/m2or ±5%rdg; whichever is greater
BTU (ft2*h)
0 to 634
0.1
±3 BTU (ft2*h) or ±5%rdg; whichever is greater
*Additional temperature error: ±0.38 W/m2 or ±0.12 BTU ft2*h per °C from 25°C
Copyright ©2018 FLIR Systems, Inc.
All rights reserved including the right of reproduction in whole or in part in any form
ISO-9001 Certified
www.extech.com