Extron electronics AAP 100 User manual

1-1AAP 100 and MAAP 100 • Installation Guide
Extron AAP 100 and MAAP 100 Installation Guide
Installing the AAP 100 and MAAP 100
The following procedure is for mounting the AAP 100 and MAAP 100 panels on
hard surfaces (plywood, hardwood, etc.). For soft surfaces (particle board, drywall,
etc.), additional hardware such as anchors may be required (not provided).
1. Photocopy the appropriate full size rough-in template from the other side of
this page. Cut out the center portion of the template up to the dashed
guidelines.
CAUTION
Be sure to photocopy the template at exactly 100%. Using a template that
has been altered will cause you to cut an opening of the wrong size and
may result in permanent damage to the surface.
2. Place the template copy in the desired location on the installation surface.
Use a soft pencil to mark the guidelines for the opening on the surface.
3. Use a jigsaw or small hand saw to carefully cut away the material within the
guidelines. Check the opening size by placing the panel against the opening.
If needed, use a saw, file, or sandpaper to enlarge the opening.
4. Cable the AAP(s)/MAAP(s) and install them on the panel.
5. Place the panel against the surface so that the AAP(s)/MAAP(s) fit into the
opening. Mark the locations of the two wall mounting holes on the surface.
6. If desired, remove the panel and drill ¼" deep pilot holes (half the width of
the shaft of the screw) at the marked locations. Replace the panel.
7. Use two ½" (1.3 cm) long, #6 flat headed wood screws (provided) to fasten
the panel directly onto the surface. Hand tighten the screws.
Product Dimensions
0.000 0.250 3.000 3.250
1.750
2 x 0.875
0.000
0.100
1.750
2 x 0.875
0.000 0.250 4.250 4.500
0.000
0.100
68-837-01 Rev. A
Printed in the USA
05 03
AAP 100
MAAP 100
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

Installation Guide, cont’d
AAP 100 and MAAP 100 • Installation Guide1-2
Installation Templates
Template for
the MAAP 100
Template for
the AAP 100
The dashed line indicates the
recommended cut-out area
for the installation surface.
1.5" H x 2.25" W
(3.8 cm H x 5.7 cm W)
The solid, outer line
represents the outside
edge of the panel.
1.75
" H x 3.25 " W
(4.45 cm H x 8.25 cm W)
Template for
the MAAP 100
The dashed line indicates the
recommended cut-out area
for the installation surface.
1.5" H x 3.5" W
(3.8 cm H x 8.9 cm W)
The solid, outer line
represents the outside
edge of the panel.
1.75" H x 4.5" W
(4.45 cm H x 11.4 cm W)
Template for
the AAP 100
© 2003 Extron Electronics. All rights reserved.
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax [phone]
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax [phone]
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax [phone]
Extron Electronics, Japan
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku,Tokyo 102-0074 Japan
+81.3.3511.7655
Fax [phone]
www.extron.com
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]