Extron electronics UCS FT 901 User manual

1
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
UCS FT 901 and UCS FR 902 • Setup Guide
This guide provides basic instructions for an experienced technician to install and
congure the Extron UCS 900 Series. The UCS FT 901 and UCS FR 902 extends USB
signals from USB 3.2, 2.0, and 1.1 peripheral devices located up to 820 feet (250 meters)
away to a USB 3.2 host computer over multimode ber optic cable, with a SuperSpeed
data transfer rate of up to 5 Gbps. The transmitter features a USB Type-C connector.
The receiver features a built-in active two-port hub that supplies up to 5 V, 1.5 A from
each port to power attached devices.
See the UCS FT 901 and UCS FR 902 User Guide, available at www.extron.com, for more information.
NOTE:
• This product supports USB data ONLY. DisplayPort Alt Mode and Power Delivery are NOT supported.
• The use of a USB 2.0 hub on the UCS FR 902 is not recommended. If a hub is needed in the system, Extron
recommends the use of a USB 3.2 hub. Please contact your Extron AE for more details.
Installation
ATTENTION: Installation and service must be performed by authorized personnel only.
ATTENTION : L’installation et l’entretien doivent être effectués uniquement par un technicien qualifié.
Mounting
The UCS FT 901 and UCS FR 902 can be rack mounted, furniture mounted, or placed on a tabletop with the provided rubber feet.
For ZipClip mounting instructions, see the UCS FT 901 and UCS FR 902 User Guide at www.extron.com.
Connecting Cables
WARNING: Fiber optic connectors emit continuous invisible light, which may be harmful to the eyes; use with caution. Do
not look into the fiber optic cable connectors or into the fiber optic cables themselves. Plug the attached dust caps into the
optical transceivers when the fiber cable is unplugged.
ADVERTISSEMENT : Les connecteurs de fibre optique émettent une lumière invisible continue, qui peut être dangereuse
pour les yeux ; à utiliser avec précaution. Ne pas fixer directement les connecteurs optiques ou les câbles fibre optique.
Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque le câble fibre optique est
débranché.
The illustration below shows connections for the UCS FT 901 and UCS FR 902.
POWER
12V
HOST
USB-C
SS 5G Tx
OUTPUT
Rx
1
24
POWER
12V
1.0A MAX
INPUT
OUTPUTS
1
2
4
PO
WER
12
V
1
.
0
A MAX
INPUT
O
UTPUT
S
POWER
12V
DEVICES INPUT
Tx
1
Rx
2
1.5 A
1.6A MAX
Ground
+12 VDC input
G
External Power Supply
(12 VDC, 2.0 A max.)
Ground all
Devices
Ground
+12 VDC input
G
External Power Supply
(12 VDC, 0.5 A max.)
Ground all
Devices
0.1A MAX
USB
USB Camera
Receiver
USB
Laptop
5
5
5
3
3
3
6
6
65
5
5
Transmitter
Multimode Fiber Optic Cable
Compatible with USB 3.2, 2.0, 1.1
peripheral devices
1
1
12
2
2
3
3
3
4
4
4
Compatible with USB 3.2
host ports ONLY

2
68-3621-50 Rev. B
04 21
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2021 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
Connecting Power
Power off all devices that will be directly connected to the receiver.
Wire the 24 W power supply (see previous page, 1) to the
transmitter 2-pole captive screw connector (3), and the 6 W
power supply (2) to the receiver (see the illustration at right for
wiring instructions).
NOTE: The UCS FT 901 (transmitter) can also be powered
by the Host device, without the need for the external
power supply.
Once a unit receives power, the front panel Power LED (see the
unit illustrations on the right, A) lights.
Connecting the Host (Transmitter)
1. Connect a USB Type A-to-C (or Type C-to-C) cable from the
Host device to the transmitter Host port (4). The Host LED
on the transmitter (B) lights as communication between the
transmitter and host device is established.
NOTE: The transmitter is compatible with USB 3.2
host ports ONLY. USB 3.2 ports are either blue Type
A, Type C, or labeled with a SuperSpeed trident logo
(see below).
®
2. Connect a multimode fiber optic cable from the output port of the transmitter to the input port of the receiver (5).
3. Once the cable is connected to both the transmitter and receiver, the front panel Link LEDs light steadily (C).
4. Mount the devices, if appropriate.
5. Power on the host device. The transmitter (UCS FT 901) Host LED (B) lights when the computer recognizes the transmitter.
Connecting the Devices (Receiver)
Connect up to two USB peripheral devices to the receiver devices ports (6). The order of connection does not matter.
The UCS FR 902 (receiver) supplies up to 5 V, 1.5 A to each connected peripheral device.
The system is now ready to operate.
Captive Screw Connector
Tie Wrap
Heat
Shrink 1/8"
(3 mm)
7/8"
(22 mm)
3/16"
(5 mm) Max.
eUCS FR 902
LINK
STATUS
POWER
12V
--A MAX
DEVICES INPUT
Tx
1
Rx
2
1.5 A
A C
A C
B
UCS FT 901e
LINK
HOST
STATUS
POWER
12V
0.1A MAX
HOST
USB-C
SS 5G Tx
OUTPUT
Rx
A B C
A B
C