Extron electronics FOX T UWP 302 User manual

User Guide
FOX T UWP 302
Fiber Optic Extender
Two Input Fiber Optic Transmitter
68-2092-01 Rev. A
07 13

Safety Instructions • English
WARNING: This symbol, , when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT: Ce pictogramme, , lorsqu’il est utilisé sur
le produit, signale à l’utilisateur la présence à l’intérieur du boîtier
du produit d’une tension électrique dangereuse susceptible de
provoquer un choc électrique.
ATTENTION: Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.fr.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind
und die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.de.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con
el equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.es.
Chinese Simplified（简体中文）
警告：产品上的这个标志意在警告用户该产品机壳内有暴露的危险
电 压 ，有 触 电 危 险 。
注意：产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修）说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容，敬请访问 Extron 网站 www.extron.cn，参见 Extron
安全规范指南，产品编号 68-290-01。
Chinese Traditional（繁體中文）
警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意 若產品上使用此符號，是為了提醒使用者。
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細
資訊，請瀏覽 Extron 網站：www.extron.cn，然後參閱《Extron 安全性與法規
遵守手冊》，準則編號 68-290-01。
Japanese
警告:この記号 が製品上に表示されている場合は、筐体内に絶縁されて
いない高電圧が流れ、感電の危険があることを示しています。
注意:この記号 が製品上に表示されている場合は、本機の取扱説明書に
記載されている重要な操作と保守(整備)の指示についてユーザーの
 注意を喚起するものです。
安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に
つ い て は 、エ ク スト ロ ン の ウェブ サ イト www.extron.jpより
『Extron Safety and Regulatory Compliance Guide』 (P/N 68-290-01) をご覧ください 。
Korean
경고: 이 기호 , 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 , 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련
항목에 대한 자세한 내용은 Extron 웹 사이트(www.extron.co.kr)의
Extron 안전 및 규제 준수 안내서, 68-290-01 조항을 참조하십시오.

FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference; the user must correct the interference at his own expense.
NOTE: For more information on safety guidelines, regulatory compliances, EMI/
EMF compatibility, accessibility, and related topics, see the “Extron Safety and
Regulatory Compliance Guide” on the Extron website.
FDA/IEC 60825-1 Requirements
CLASS 1 LASER PRODUCT
Complies with FDA performance standards for laser products except for deviations pursuant
to Laser Notice No. 5, dated June 24, 2007.
The product is intended to be used with the fiber optic cables fully installed.
This product meets the applicable requirements of IEC 60825-1, Edition 1 (2007).
Any service to this product must be carried out by Extron Electronics and its qualified
service personnel.
Copyright
© 2013 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks(®), registered service marks(SM), and trademarks(TM) are the property of
RGBSystems, Inc. or Extron Electronics:
Registered Trademarks (®)
AVTrac, Cable Cubby, CrossPoint, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, GlobalViewer, Hideaway, Inline, IPIntercom, IPLink,
Key Minder, LockIt, MediaLink, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, System Integrator,
TeamWork, TouchLink, V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP and XTP Systems
Registered Service Mark(SM) : S3 Service Support Solutions
Trademarks (™)
AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), AIS (Advanced Instruction Set), Auto-Image, CDRS (Class D
Ripple Suppression), DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), DriverConfigurator, DSPConfigurator, DSVP
(Digital Sync Validation Processing), FastBite, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, ProDSP, QS-FPC (QuickSwitch Front Panel
Controller), Scope-Trigger, SIS, Simple Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, XTRA, ZipCaddy, ZipClip

Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
WARNING: A warning indicates a situation that has the potential to result in death or
severe injury.
CAUTION: A caution indicates a situation that may result in minor injury.
ATTENTION: Attention indicates a situation that may damage or destroy the product or
associated equipment.
NOTE: A note draws attention to important information.
TIP: A tip provides a suggestion to make working with the application easier.
Software Commands
Commands are written in the fonts shown here:
^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C
[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]
EX! *X1&*X2)*X2#*X2! CE}
NOTE: For commands and examples of computer or device responses mentioned
in this guide, the character “0” is used for the number zero and “O” represents the
capital letter “o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the File menu, select New.
Click the OK button.
Specifications Availability
Product specification are available on the Extron website, www.extron.com.

Contents
SIS Conguration and Control .................. 13
Simple Instruction Set Control .......................... 13
SIS Programming Guide ............................... 13
Command and Response Tables for SIS
Commands ................................................. 16
FOX Extenders Control Program............... 21
Installing the Software....................................... 21
Starting the Software........................................ 22
Using the Software ........................................... 22
Top Menu ..................................................... 23
Main Screen ................................................. 30
Reference Information ............................... 38
Firmware Loader .............................................. 38
Downloading Extron Firmware Loader .......... 38
Installing Firmware Loader ............................ 39
Firmware Updates ............................................ 39
Downloading Firmware ................................. 39
Installing Firmware with Firmware Loader...... 40
Introduction ................................................... 1
About This Guide................................................ 1
About the FOX T UWP 302................................. 1
System Compatibility ...................................... 1
Cable Transmission Modes............................. 1
Key Features ...................................................... 2
Application Diagram ........................................... 3
Installation and Operation ........................... 4
Installation Overview ........................................... 4
Rear Panel Features ........................................... 5
Front Panel Features........................................... 6
Outside-the-Faceplate Features...................... 6
Under-the-Faceplate Features ........................ 7
Mounting and Making Connections .................... 8
Mounting ........................................................ 8
Connecting the HDMI Connector.................... 9
Wiring for Fiber Communication...................... 9
Wiring for Remote RS-232 and Alarm
Communication ........................................... 10
Wiring the Power Supply .............................. 11
Operation ......................................................... 12
Initial Power Up............................................. 12
System Reset ............................................... 12
ivFOX T UWP 302 Wallplate Transmitter • Contents

FOX T UWP 302 Wallplate Transmitter • Contents v

Introduction
This section describes general information about this guide and the FOX T UWP 302
Universal Wallplate Transmitter and selected device features. Topics in this section include:
• About This Guide
• About the FOX T UWP 302
• Key Features
• Application Diagram
About This Guide
This guide describes installation, operation, and control procedures, and reference
information for the FOX T UWP 302 Universal Wallplate Transmitter. In this guide,
“FOX T UWP 302” refers to the FOX T UWP 302 Universal Wallplate Transmitter in
singlemode or multimode.
About the FOX T UWP 302
The Extron FOX T UWP 302 is a three-gang universal wallplate transmitter with a two input
integrated switcher that provides long haul transmission of HDCP-compliant HDMI, RGBHV,
or HD component video; stereo audio; and RS-232 signals over fiber optic cabling. It has
dedicated connectors for RGB, HDMI, and audio.
To configure and control the FOX T UWP 302, connect a host device, such as a computer,
and enter Simple Instruction Set (SIS) commands (see Simple Instruction Set Control
on page 13) or use the FOX Extenders Control Program (see FOX Extenders Control
Program on page 21).
System Compatibility
The FOX T UWP 302 operates in either of two modes, selected under RS-232 control, for
compatibility with other, non-HDMI, units:
• Plus — Supports resolutions up to 1920x1200 @ 60 Hz, including HDTV 1080p/60 Hz.
The fiber optic output of the transmitter can be received only by one of six receivers: a
FOXBOX HDMI Rx, FOXBOX DVI Plus Rx, PowerCage HDMI Rx, PowerCage FOX DVI
Plus Rx, FOXBOX SR HDMI, and PowerCage FOX SR HDMI.
• Non-Plus — Supports resolutions up to 1600x1200 and 1080p @ 60 Hz (including
HDTV 1080p/60 Hz), is HDCP compliant, and does not contain embedded audio
(analog audio is still supported). The fiber optic output of the transmitter can be received
by any FOXBOX, PowerCage FOX, and FOX 500 VGA and DVI unit, including the Plus
and non-Plus units.
Cable Transmission Modes
The transmitter is categorized by the type of fiber optic cable, multimode
(FOX T UWP 302 MM) or singlemode (FOX T UWP 302 SM), which define the effective
range of transmission:
• Multimode — Long distance, up to 2 km (6,560 feet) (depending on the fiber cable)
• Singlemode — Very long distance, up to 30 km (18.75 miles)
1FOX T UWP 302 Wallplate Transmitter • Introduction

Key Features
High reliability and maximum performance transmission over long distance fiber
optic cabling — Transmits HDMI or analog video and stereo audio signals over very long
distances using fiber optic cabling.
Inputs — Include a female HDMI type A connector; 15-pin HD connector for RGBHV,
RGBS, or HD component video; and a 3.5 mm stereo mini-jack for unbalanced stereo
audio.
All digital technology — Delivers pixel-for-pixel transmission of video signals to ensure
optimal image quality at resolutions up to 1920x1200, including HDTV 1080p/60.
Digital conversion of analog video — Analog signals are digitized, ensuring that a
reliable, high quality digital video signal is sent to the output destination.
Auto-input switching — Automatically switches to the lowest or highest priority input with
an active video signal for simplified operation.
HDCP-compliance
Key Minder — Authenticates and maintains continuous HDCP encryption between input
and output devices to ensure quick and reliable switching in professional AV environments,
while enabling simultaneous distribution of a single source signal to one or more displays.
EDID Minder — Automatically manages EDID communication between connected devices
to ensure that all sources properly power up and reliably display content.
Audio embedding — Converts analog stereo audio signals to digital HDMI audio when the
analog input is selected.
Audio gain and attenuation adjustment capability
LED indicators for signal presence, HDCP, and power — Provides a visual indication of
system status for real-time feedback and monitoring of key performance parameters.
Multimode and singlemode availability — Available as an 850 nm multimode model for
long-range transmissions up to 2 km (6,560 feet), and a 1310 nm singlemode model for
extreme distances up to 30 km (18.75 miles).
Industry standard LC connectors — Provide reliable physical connectivity and precise
fiber core alignment.
Compatibility with the following Extron FOX series products:
• Matrix switchers — Creates HDCP-compliant signal distribution systems up to
1000x1000 and larger.
• HDMI, DVI Plus, DVI, and VGA receivers — Compatible with FOX series HDMI and
DVI Plus receivers up to 1920x1200, including HDTV 1080p/60. Compatible with
FOX series DVI and VGA receivers up to 1600x1200, including HDTV 1080p/60.
NOTE: The FOX T UWP 302 is not compatible with the FOX 3G HD-SDI, FOX 3G DVC,
or FOX AV models.
Front panel USB configuration port
Mounts in an included three-gang Decora®-style wallplate — Includes a
black or white three-gang Decora-style wallplate to blend with a wide range of
environments.
Includes LockIt HDMI cable lacing bracket
Energy-efficient external universal power supply included — Provides worldwide
compatibility, low power consumption, and reduced operating costs.
FOX T UWP 302 Wallplate Transmitter • Introduction 2

Application Diagram
The following diagram shows a typical application of the FOX T UWP 302 with two input
sources, connected to a fiber optic receiver.
12V
1.0A MAX
FOX SR HDMI
POWER
LINK
LINK
OPTICAL
RxTx
HDMIAUDIO
HDMI
AUDIO
OUTPUTS
ON
OFF
REMOTE
RS-232
Tx Rx
RS-232
OVERFIBER ALARM
Tx Rx 1 2
L R
POWER
PC
HDMI
HDCP
AUDIO INPUT
HDMI INPUT
COMPUTER INPUT
AUDIO
STANDBY
CLASS 2 WIRING
12
XPA 1002
LEVEL
1
1212
LIMITER/
PROTECT
SIGNAL
2
INPUTS OUTPUT
REMOTE
00
VOL/MUTE
10V 50 mA
100-240V 1.3A,50-60Hz
Extron
XPA 1002
Power
Amplier
Extron
SI 28
Surface-
mount
Speakers
Extron
FOX T UWP 302
Fiber Optic
Transmitter
Laptop
with HDMI
Output
Flat Panel
Display
HDMI + Audio
HDMI
Up to 30 km (18.75 miles)
Singlemode Fiber
SM Model
Audio
Audio
VGA
Laptop
with VGA
Output
Extron
FOXBOX SR HDMI
Fiber Optic Receiver
Figure 1. Typical FOX T UWP 302 Application
FOX T UWP 302 Wallplate Transmitter • Introduction 3

Installation and
Operation
This section describes procedures to cable, connect, and manually operate the
FOX T UWP 302. Topics in this section include:
• Installation Overview
• Rear Panel Features
• Front Panel Features
• Mounting and Making Connections
• Operation
Installation Overview
Install the FOX T UWP 302 into an electrical UL Listed junction box.
CAUTION: Risk of personal injury. Failure to check the items listed below may result
in personal injury.
ATTENTION: Failure to check the items listed below may result in property damage.
1. Check that installation of an electrical UL Listed junction box meets local and state
building, electrical, and safety codes.
2. Install the junction box according to the junction box installation instructions.
3. Prepare and pull the cables through the junction box.
TIP: Secure cables with clamps or ties to provide strain relief.
4. Trim back and insulate shields with heat shrink.
ATTENTION: To prevent short circuits, the outer foil shield can be cut back to the
point where the cable exits the cable clamp. Both braided and foil shields should
be connected to an equipment ground at the other end of the cable.
5. Connect cables to the rear panel connectors (see Rear Panel Features on page 5).
6. Mount the FOX T UWP 302 enclosure into the junction box (see Mounting on page 8).
7. Configure the FOX T UWP 302 with SIS commands (see Simple Instruction Set
Control on page 13) or the FOX Extenders control program (see FOX Extenders
Control Program on page 21).
8. Install the faceplate (see Mounting on page 8).
4FOX T UWP 302 Wallplate Transmitter • Installation and Operation

Rear Panel Features
Tx
Rx
Rx
Tx
1
2
G
+
REMOTE
RS-232
ALARM
POWER
12V
0.6A MAX
-
RearRight Side
a
b
c
Figure 2. FOX T UWP 302 Rear Connectors from the Side and Rear Panels
aFiber connector — For one-way video, audio, and serial
communication from the transmitter to a receiver, connect a fiber optic
cable between the Tx port on the transmitter and the Rx port on a
receiver.
To return serial data from a receiver to the transmitter (such as
responses from a controlled device) or for HDCP-compliance, connect a
fiber optic cable between the Rx port on the transmitter and the Tx port
on the receiver (see Wiring for Fiber Communication on page 9).
NOTES:
• Ensure the proper fiber optic cable is used. Typically,
singlemode fiber optic cable has a yellow jacket and multimode
fiber optic cable has an orange or aqua jacket.
• Only one fiber optic cable, transmitter-Tx-to-receiver-Rx,
is required for video, audio, and serial command transmission,
but the HDMI signal output on the receiver will not be
HDCP-compliant.
bRemote RS-232 port — For serial RS-232 control, connect a host device
to the transmitter via the leftmost poles (Tx, Rx, and G) of this 5-pole
captive screw connector (see Wiring for Remote RS-232 and Alarm
Communication on page 10 for wiring configuration).
Alarm output port — For remote monitoring of the status of fiber optic
link 2, connect a custom or furnished monitoring device to the transmitter
via the rightmost poles (1 and 2) of this 5-pole captive screw connector (see
Wiring for Remote RS-232 and Alarm Communication on page 10).
NOTE: Pins 1 and 2 short when link 2 does not detect any connection.
cPower connector — Connect the provided external 12 VDC power supply
to this 3.5 mm, 2-pole captive screw connector (see Wiring the Power
Supply on page 11).
Transmitter
to
Receiver
OPTICAL
Rx
Tx
LINK LINK
OPTICAL
Rx
Tx
Tx Rx 1 2G
Tx Rx G 1 2
FOX T UWP 302 Wallplate Transmitter • Installation and Operation 5

Front Panel Features
Outside-the-Faceplate Features
POWER
PC
HDMI
HDCP
AUDIO INPUT
HDMI INPUT
COMPUTER INPUT
AUDIO
b
d
c
a
Figure 3. FOX T UWP 302 Outside-the-Faceplate Features
aLED indicators
Power LED — Lights when the device receives 12 V from an external power supply.
PC LED — Lights when PC input is detected.
HDMI LED — Lights when HDMI input is detected.
HDCP LED — Lights if the HDMI input signal is HDCP encrypted.
Audio LED — Lights when the device detects audio with the selected input. If the
selected input has an analog audio signal above -44 dBV, the Audio LED lights
immediately, but turns off only after the audio signal level drops below the threshold
continuously for 10 seconds. If the selected input has digital embedded audio, the
Audio LED lights and remains lit as long as the digital audio signal is detected.
bAudio Input connector — Connect an audio source to the 3.5 mm TRS jack.
Tip (+)
Sleeve ( )
Sleeve ( )
Ring ( - )
Tip (+)
Audio Plugs.eps
RCA Connector
3.5 mm Stereo Plug Connector
(balanced)
Sleeve ( )
Ring (R)
Tip (L)
3.5 mm Stereo Plug Connector
(unbalanced)
Figure 4. Wiring for Unbalanced Stereo Audio
cComputer Input connector — Connect a video source to the female 15-pin HD
connector.
dHDMI Input connector — Connect a source device to the HDMI connector. This
connector can accept HDMI, DVI, or dual mode DisplayPort video signals.
FOX T UWP 302 Wallplate Transmitter • Installation and Operation 6

Under-the-Faceplate Features
LINK 1 LINK 2
HDMI INPUT
AUDIO INPUT
COMPUTER INPUT
POWER
RESET
CONFIG
PC
HDMI
HDCP
AUDIO
f
e
g
Figure 5. FOX T UWP 302 Under-the-Faceplate Features
eLink 1 and Link 2 LED indicators — Light when there is light present on the
corresponding fiber optic port.
fReset button — Press the Reset button to return device settings or firmware to the
factory default settings (see System Reset on page 12).
gConfig port — Connect a host device, such as a PC, to the mini-USB type B config
port for RS-232 protocol control of all FOX T UWP 302 functions. Configure the
FOX T UWP 302 with SIS commands (see Simple Instruction Set Control on page 13)
or the FOX Extenders control program (see FOX Extenders Control Program on
page 21).
FOX T UWP 302 Wallplate Transmitter • Installation and Operation 7

Mounting and Making Connections
Mounting
Before mounting an electrical UL Listed junction box, consider the mounting location and
prepare the surface as necessary.
Flush with
Wall Surface
Screws or Nails
Wall Stud
Junction Box
Mounting
Scr
ews
(6 Plcs)
Extron
FOX T UWP 302
Universal Wallplate
Transmitter
b
e
f
Figure 6. Mounting the FOX T UWP 302 Into a Junction Box
1. Mount the junction box in the wall or floor, following the directions provided with the
box.
2. Run the cables through the junction box.
TIP: Secure cables with clamps or ties to provide strain relief.
ATTENTION: To prevent short circuits, the outer foil shield can be cut back to the
point where the cable exits the cable clamp. Both braided and foil shields should
be connected to an equipment ground at the other end of the cable.
3. Disconnect power from all devices at the source.
4. Connect all cables to the FOX T UWP 302 rear panel connectors.
5. Secure the FOX T UWP 302 enclosure to the box using three of the provided screws
into the slots at the top and bottom of the device.
6. Fasten the Decora wallplate onto the enclosure using six of the provided screws in the
holes at the top and bottom.
FOX T UWP 302 Wallplate Transmitter • Installation and Operation 8

Connecting the HDMI Connector
Use an Extron LockIt Lacing Bracket to secure an HDMI cable to each device as follows:
3
a
b
cd
e
Figure 7. Installing the LockIt Lacing Bracket
1. Plug the HDMI cable into the panel connection.
2. Loosen the HDMI connection mounting screw from the panel enough to allow the
LockIt lacing bracket to be placed over it. The screw does not have to be removed.
3. Place the LockIt lacing bracket on the screw and against the HDMI connector, then
tighten the screw to secure the bracket.
ATTENTION: Do not overtighten the HDMI connector mounting screw. The shield
to which it fastens to is very thin and can easily be stripped.
4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing
bracket as shown.
5. While holding the connector securely against the lacing bracket, use pliers or a similar
tool to tighten the tie wrap, then remove any excess length.
Wiring for Fiber Communication
WARNING: Risk of serious physical injury: This device outputs
continuous invisible light, which may be harmful to the eyes; use with
caution.
• Do not look into the rear panel fiber optic cable connectors or into
the fiber optic cables themselves.
• Plug the attached dust caps into the optical transceivers when
the fiber cable is unplugged.
NOTES:
• Ensure the proper fiber optic cable is used for the transmitter and
receiver. Typically, singlemode fiber optic cable has a yellow jacket
and multimode fiber optic cable has an orange or aqua jacket.
• Only one fiber optic cable, transmitter-Tx-to-reciever-Rx, is
required for video, audio, and serial command transmission.
However, for only one fiber optic cable, the HDMI signal output by
the receiver is not HDCP-compliant.
• To receive responses from the controlled device and for HDCP
compliance, install both fiber optic cables and leave link 2
enabled.
Transmitter
to
Receiver
OPTICAL
Rx
Tx
LINK LINK
OPTICAL
Rx
Tx
FOX T UWP 302 Wallplate Transmitter • Installation and Operation 9

Wiring for Remote RS-232 and Alarm Communication
The Remote RS-232 and Alarm connector is for RS-232 control (such as updating firmware,
status queries, and various control functions) and the alarm feature. Wire the connector as
shown in figure 8 below.
RxTx
Alarm Device
RS-232 Device
G
REMOTE
RS-232 ALARM
Tx Rx G1 2
12
Figure 8. Wiring the Remote RS-232 and Alarm Connector
ATTENTION: The length of exposed wires is critical. The ideal length is
3/16 inch (5 mm).
• Longer bare wires can short together.
• Shorter wires are not as secure in the connectors and could be pulled out.
Cross the Tx and Rx lines once between the source and the target.
The alarm pins do not produce any discrete on or off or voltage signals. It is an internal relay
to connect or disconnect a custom alarm circuit.
NOTE: If power is lost or if link 2 optical light is disconnected, lost, or broken, alarm
pins 1 and 2 internally short.
FOX T UWP 302 Wallplate Transmitter • Installation and Operation 10

Wiring the Power Supply
Connect 12 VDC power supply to the 3.5 mm, 2-pole captive screw connector.
SECTION A–A
AA
Power Supply
Output Cord
2-Pole Captive Screw
Connector
Ridges
Smooth
Tie Wrap
3/16”
(5 mm) Max.
Figure 9. Power Connector Wiring
CAUTION: Electric shock hazard. The two power cord wires must be kept separate
while the power supply is plugged in. Remove power before wiring.
ATTENTION:
• This product is intended to be supplied by a Listed Power Unit marked “Class 2”
or “LPS,” rated 12 VDC, 1.0 A minimum. Always use a power supply supplied by
or specified by Extron. Use of an unauthorized power supply voids all regulatory
compliance certification and may cause damage to the supply and the end product.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The installation must always be in accordance with the
applicable provisions of National Electrical Code ANSI/NFPA 70, article 75 and
the Canadian Electrical Code part 1, section 16. The power supply shall not be
permanently fixed to a building structure or similar structure.
• Power supply voltage polarity is critical. Incorrect voltage polarity can damage the
power supply and the unit. The ridges on the side of the cord identify the power cord
negative lead.
• The length of the exposed (stripped) copper wires is important. The ideal length is
3/16 inch (5 mm).
TIP: Do not tin the stripped power supply leads. Tinned wires are not as secure in the
captive screw connectors and could be pulled out.
FOX T UWP 302 Wallplate Transmitter • Installation and Operation 11

Operation
After all devices are connected and powered, the system is fully operational. The
FOX T UWP 302 can be configured through SIS commands (see Simple Instruction Set
Control on page 13) or the FOX Extenders control program (see FOX Extenders Control
Program on page 21).
Initial Power Up
Upon initial power up, all the front panel LEDs blink simultaneously. They blink once to
indicate the device is a multimode device or twice to indicate the device is a singlemode
device. Afterwards, the LEDs return to their normal signal presence indication.
If a different SFP module or no SFP module is connected, the LEDs first blink once or twice
to identify the device and then blink continuously.
System Reset
Use the Reset button beneath the faceplate to return the device to default settings or to
restore factory-shipped firmware (see to the Reset Mode Summary table below for more
details). If necessary, remove the faceplate.
Reset Mode Summary
Mode Mode Activation Result Purpose/Notes
Factory Reset
1Hold the Reset button down
while applying power to the
device.
NOTE: After a mode 1
reset, update the device
with the latest firmware
version. DO NOT operate
the firmware version that
results from this mode
reset.
• The device reverts to the factory
default firmware.
• All user files and settings (audio
adjustments, audio input selection,
input selection, auto-switch mode,
picture adjustments, and input
video format) are maintained.
Use mode 1 to revert
to factory firmware for
a single power cycle if
an incompatibility issue
arises.
Reset to Factory Defaults
5Hold the Reset button down
for about 9 seconds or until
the Power LED blinks three
times. Then press the Reset
button momentarily (for
<1 second) within 1 second.
NOTE: The reset
procedure is aborted if the
second momentary press
does not occur within one
second.
• Mode 5 performs a complete
reset to factory defaults except for
firmware.
• Reset all user modifiable
configurations to default values
including real-time adjustments.
• The Power LED blinks 4 times in
quick succession during the reset.
Use mode 5 to start
over with configuration
or uploading.
NOTE: This is
equivalent to SIS
command ZXXX.
FOX T UWP 302 Wallplate Transmitter • Installation and Operation 12

SIS Configuration
and Control
This section describes remote control of the FOX T UWP 302 through SIS commands
and basic installation instructions for the FOX Extenders Control Program (see to the FOX
Extenders Control Program Help File for configuration and control details).
To enable serial control of the transmitter, use a computer running the HyperTerminal or
Extron DataViewer utility, or a control system to enable serial control of the transmitter.
Connect the computer to the FOX T UWP 302 through the front panel Config port or the
rear panel Remote RS-232 connector (see Installation and Operation on page 4).
The protocol for the RS-232 port is as follows: 9600 baud, no parity, 8 data bits, 1 stop bit,
no flow control.
Simple Instruction Set Control
SIS Programming Guide
Host-to-device and device-to-host communication
SIS commands consist of one or more characters per field. No special characters are
required to begin or end a command sequence. When the FOX T UWP 302 determines that
a command is valid, it executes the command and sends a response to the host device. All
responses from the transmitter or receiver to the host end with a carriage return and a line
feed (CR/LF = ]), which signals the end of the response character string. A string is one or
more characters.
Device-initiated messages
When a local event occurs, the device responds by sending a message to the host. The
device-initiated message may depend on whether the device is a multimode or singlemode
unit. They are listed below.
© Copyright 2013, Extron Electronics FOX T UWP 302 MM, Vx.xx, 60-1232-xx
© Copyright 2013, Extron Electronics FOX T UWP 302 SM, Vx.xx, 60-1232-xx
Vx.xx is the firmware version number.
Reconfig]
The FOX T UWP 302 returns this message when there is any change to the input frequency
on the currently selected input.
1LnkX%•2LnkX%•VidX%•AudX%•X1)•TX]
The FOX T UWP 302 returns this status message whenever a change in the fiber link, video,
or audio connection occurs. X% indicates whether the link is present or not present
(0= not present, 1= present) and X1) represents whether the device is multimode or
singlemode (MM = multimode, SM = singlemode).
13FOX T UWP 302 Wallplate Transmitter • SIS Configuration and Control

Error responses
When the FOX T UWP 302 receives an SIS command and determines it is valid, it performs
the command and sends the corresponding response to the host device. If the command is
determined invalid or contains invalid parameters, the transmitter returns an error response
to the host. The error response codes are:
E01 = Invalid input number E13 = Invalid parameter
E06 = Invalid switch attempt in this mode E14 = Not valid for this configuration
E10 = Invalid command E17 = Invalid command for signal type
E12 = Invalid port number E22 = Busy
Using the command and response table for SIS commands
The Command and Response Tables begin on page 16. Lowercase letters are
acceptable in the command field except where indicated. Figure 10 shows the hexadecimal
equivalent of ASCII characters used in the command and response tables.
ASCII to Hex ConversionTable
•
Space
Figure 10. ASCII to Hexadecimal Conversion
Symbol definitions
]= Carriage return and line feed
¦ or }= Carriage return with no line feed
•= Space
Eor W = Escape key
FOX T UWP 302 Wallplate Transmitter • SIS Configuration and Control 14