Extron electronics HC 402 EU User manual

1
IMPORTANT:
Go to www.extron.com for the complete
user guide,
installation instructions,
and
specifications bef
ore connecting the
pr
oduct to the po
wer source.
HC 402 EU/MK • Setup Guide
HC402 System
The Extron HC402EU and HC402MK systems are AV presentation solutions that incorporate a built-in control processor for
display control via HDMI Consumer Electronics Control (CEC), RS-232, IR, or Ethernet. Each system also includes digital I/O ports.
Each system is a transmitter-receiver pair that is factory-optimized to work together as if it were a single unit.
Together each transmitter-receiver system extends video, audio, and control signals up to 230feet (70m) over a single CATxcable.
Each system offers two auto-input switching modes, one of which automatically selects sources based on input signals and also
allows manual source selection via buttons. Auto-switching modes can be enabled or disabled via Extron Product Configuration
Software (PCS). The “last connected” auto-switching mode is enabled by default.
The HC402EU and HC402MK each feature two AV inputs and one output. Each consists of a one-input transmitter (HCT101EU
or HCT101MK) and a scaling receiver (HCR102) that has one HDMI input and one connection from the transmitter. The transmitter
can be mounted into a standard EU or MK 1-gang junction box. The receiver is wall, furniture, or rack mountable.
Transmitter
The HCT101EU or HCT101MK transmitter includes one digital (HDMI) video
input and one analog audio input. The extended HDMI video signal can be
HDCP-compliant.
Receiver
The HCR102 receiver incorporates a high performance, HDCP compliant scaler
that scales video to provide a consistent output resolution to a display. It accepts
video with resolutions from 480i up to 1920x1200, 1080p, and 2K, and performs
upscaling and downscaling with multiple output rates up to 1920x1200, including
HDTV 1080p/60 and 2K. The receiver includes an on-screen display, test
patterns, and EDID Minder.
This guide provides instructions for an experienced installer to install the HCT101EU or HCT101MK and the HCR102. The guide
provides information needed to configure the most essential settings for the system and the receiver. It also describes basic
operations using front panel controls and the on-screen display (OSD) menu system. Full details are available in the HC400
Series User Guide.
POWER
12V
2.0A MAX
INPUTS OUTPUTS
1
TP
HDMI
L R
AUDIO
HDMI/CEC
SIG LINK
IN
COM IR DIGITAL I/O
1 2S GTx Rx G G 3 4 G
HCR 102
LAN
e
HDMI IN
Ethernet
PC with
GlobalViewer
Enterprise
TCP/IP
Network
HCR 102
Scaling Receiver
Display
HDMI,
CEC
Twisted Pair Cable (AV)
230'
HDMI
MODEL80
FLATPANEL
HCT 101 EU
Transmitter
Side Front
Extron
OCS 100W
Wall Mount
Occupancy
Sensor
Ethernet
Room
Wireless Access
Point
Tablet
RESET
A/PoE B
POWER
12V
1.7A MAX
HDMI HDMI Tx Rx G
RS-232
COM
LAUDIO R
OUTPUT
1
C T
2
C T
3
C T
4
C T G +V
CONTACT / TALLY LAN
INPUT OUTPUT
Extron
ShareLink Pro 1000
Wireless and Wired
Collaboration
Gateway
HDMI
Ethernet
TCP/IP
Network
Figure 1. An HC 402 System Application
It does not include input selection buttons
and LEDs.
HCT101EU HCT101MK
HCR102

2
HC 402 EU/MK • Setup Guide (Continued)
Panels and Features
Front Panel Features
CONFIG
HCR 102
1
INPUT
LPCM-2CH
MULTI-CH
HDCP
SIGNAL
R
MENU
ENTER
HOLD FOR 720p/1080p
1
AUDIO
HC
R 102
AI JB
C
DHFGE
Figure 2. HCR102 Front Panel (Above),
HCT101EU and HCT 101 MK Front Panels (Right)
AConfiguration (Config) connector (USB mini-B), page 11
BInput selection button and LED, page 14
CInput signal presence (Signal) LED, page 14
DHDCP status LED, page 14
EAudio input type LEDs (LPCM-2Ch and Multi-Ch, page 14
FMenu button,
GEnter button, and
HNavigation (right , left , up , and down arrow) buttons (see
To configure the AV settings using the OSD and front panel buttons:
on page7)
IPower LED (HCT101EU or HCT101MK), power and reset indicator
LED (HCR102) — This green LED indicates either the power status of
the HCT transmitter or the HCR102 receiver, or the reset mode of the
receiver. For LED indications, see the table below.
JReset button (HCR102) — Pressing this recessed button causes
various product settings to be reset to the factory defaults (see Reset
Modes: a Brief Summary on page15).
Reset and power LED (I) indications are as follows:
HCT 101 EU or MK Transmitter HCR 102 Receiver
• Off — The unit is not powered on.
• On, lit amber — The unit is powered on
but there is no active signal at that input.
• On, lit green — The unit is powered on
and there is an active signal at that input.
• Off — The unit is not powered
on.
• On, lit steadily — The unit is
powered on.
• Blinking — The unit is
powering up or the HCR102
is performing a reset. The
blink pattern depends on the
selected reset mode.
For full descriptions of reset
modes, how to use the reset
button to activate them, and details
of LED indications of each mode,
see the HC400 Series User Guide.
e
HDMI IN
e
HDMI IN
HCT 101 MK Front (With Frame)
HCT 101 EU Front (With Frame)
I
Input
2
NOTE: For other connectors on
the HCT, see Rear and Side
Panel Features on page3.
Rear and Side Panel Features
POWER
12V
2.0A MAX
INPUTS OUTPUTS
1
TP
HDMI
LR
AUDIO
HDMI/CEC
SIG LINK
IN
COMIRDIGITAL I/O
12SGTx Rx GG34G
HCR 102
LAN
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
00-05-A6-XX-XX-XX
A F ND G H K L M
HCR 102 Rear
O
Figure 3. HCR102 Rear Panel
APower input connectors, page 13
DHDMI input connectors, page 10
ETransmitter output RJ-45 connector
(twisted pair interconnection),
page 10
FReceiver input RJ-45 connector
(twisted pair interconnection),
page 10
GHDMI/CEC output connector,
page 11
HAnalog audio output connector,
page 11
KCOM RS-232 control port,
page 11
LIR output control port, page 11
MDigital I/O (digital input/output)
control ports,
page 12
NLAN (Ethernet) connector and
LEDs, page 12
OMAC address (on side of receiver),
page 12
QGrounding screw, page 12
NOTE: Features
B, C, I, J, and
Pare available on other HC400
Series transmitter models.
POWER
12V
AMAX
0.7
HCT 101 MK
Rear
POWER
12V
AMAX
0.7
HCT 101 EU
Rear
e
HDMI IN
HCT 101 EU/MK
Device Module
Front
A
E
Q
Q
A
E
D
Figure 4. HCT101EU and MK Front Panel (Top Left), Rear Panels (Right)
These features are as follows:
BAnalog audio input connector (HCT
102, HCT 102 D)
CAnalog RGB video input (input 2)
(HCT 102, HCT 102 D)
IRemote control contact input ports
(HCT 102, HCT 102 D)
JRemote control tally output ports
(HCT 102)

3
Rear and Side Panel Features
POWER
12V
2.0A MAX
INPUTS OUTPUTS
1
TP
HDMI
LR
AUDIO
HDMI/CEC
SIG LINK
IN
COMIRDIGITAL I/O
12SGTx Rx GG34G
HCR 102
LAN
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
00-05-A6-XX-XX-XX
A F ND G H K L M
HCR 102 Rear
O
Figure 3. HCR102 Rear Panel
APower input connectors, page 13
DHDMI input connectors, page 10
ETransmitter output RJ-45 connector
(twisted pair interconnection),
page 10
FReceiver input RJ-45 connector
(twisted pair interconnection),
page 10
GHDMI/CEC output connector,
page 11
HAnalog audio output connector,
page 11
KCOM RS-232 control port,
page 11
LIR output control port, page 11
MDigital I/O (digital input/output)
control ports,
page 12
NLAN (Ethernet) connector and
LEDs, page 12
OMAC address (on side of receiver),
page 12
QGrounding screw, page 12
NOTE: Features
B, C, I, J, and
Pare available on other HC400
Series transmitter models.
POWER
12V
AMAX
0.7
HCT 101 MK
Rear
POWER
12V
AMAX
0.7
HCT 101 EU
Rear
e
HDMI IN
HCT 101 EU/MK
Device Module
Front
A
E
Q
Q
A
E
D
Figure 4. HCT101EU and MK Front Panel (Top Left), Rear Panels (Right)
These features are as follows:
BAnalog audio input connector (HCT
102, HCT 102 D)
CAnalog RGB video input (input 2)
(HCT 102, HCT 102 D)
IRemote control contact input ports
(HCT 102, HCT 102 D)
JRemote control tally output ports
(HCT 102)

4
HC 402 EU/MK • Setup Guide (Continued)
Installation and Configuration
ATTENTION:
• Installation and service must be performed by experienced personnel.
• L’installation et l’entretien doivent être effectués par du personnel expérimenté.
Step 1 — Get Ready
1. Familiarize yourself with the features of the transmitter and receiver (see Front Panel Features and Rear and Side Panel
Features on page3).
2. Download and install the latest version of the following:
• PCS Product Configuration Software — for detecting and configuring the AV settings for the transmitter-receiver pair
• Toolbelt software — for discovering the HCR102 receiver and other control products on the network, for managing
core settings, and for upgrading firmware if the need arises
• Global Configurator®(GC) software — for setting up and configuring the control system. GCProfessional and GCPlus
modes include a link to the Toolbelt software.
• IPLink®Pro device drivers — for use with GC, to make control of other AV devices possible
All are available from www.extron.com (see Locating Software, Firmware, and Driver Files on the Extron Website on page16).
3. Obtain network information for the unit from the network administrator. You will need the following details for each HCR102
receiver and for any other Extron Pro control product that is part of the system:
DHCP setting (on or off) Subnet mask Username
Device (HCR102) LAN IPaddress Gateway IP address Passwords
4. Write down the MAC address of each HCR102 (see figure 3, Oon the previous page) or other IPLinkPro device to be used.
5. Obtain model names and setup information for devices the HCR102 will control.
Step 2 — Mount the Receiver, Prepare the Installation Site for
the HCT101EU or HCT101MK
Turn off or disconnect all equipment power sources and mount the
transmitter and receiver as required.
Mounting the HCR102
The HCR102 receiver ships with furniture mounting brackets
attached for mounting to furniture or a wall.
NOTE: The receiver is designed so that its vents face
away from the wall or furniture when mounted in order to
achieve optimal air circulation and cooling.
Each receiver is one inch high, one half rack wide, and can
be rack mounted. The product page on www.extron.com
includes links to recommended optional rack shelves or rack
mounting kits. Alternatively, you can remove the pre-installed
furniture mounting brackets and attach four rubber feet at the
corners of each unit and place it on a table or desk.
Observe local and UL safety guidelines for mounting devices
to equipment racks. See the HC400 Series User Guide for UL
rack mounting guidelines.
Prepare the Installation Site for the HCT101EU or HCT101MK
ATTENTION:
• Installation and service must be performed by authorized personnel only.
• L’installation et l’entretien doivent être effectués uniquement par un technicien qualifié.
• Extron recommends installing the HCT101EU or HCT101MK into a grounded electrical junction box.
• Extron recommande d’installer le HCT101EU ou HCT101MK dans une boîte de dérivation électrique mise à la terre,
certifiée UL.
1. and of any TouchLinkPro touchpanels or NBP button panels that will be
part of the system
POWER
12V
--A MAX
INPUTS OUTPUTS
1
TP
HDMI
L R
AUDIO
HDMI/CEC
SIG
LINK
COM IR DIGITAL I/O
1 2
S GTx Rx G G 3 4 G
HCR 102
LAN
IN
Figure 5. Mounting the Receiver
Rev. B: Changed
French text in the
second Attention
per Christele.

5
ATTENTION:
• If the HCT will be installed into fine furniture, it is best to hire a licenced, bonded craftsperson to cut the access hole and
perform the physical installation so the surface will not be damaged.
• S’il est prévu d’installer le HCT dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et qualifié pour
couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.
• Follow all national and local building and electrical codes that apply to the installation site.
• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.
Americans with Disabilities Act (ADA) compliance
When planning where to install the HC system, you may need to consider factors affecting accessibility of the units such as height
from the floor, distance from obstructions, and how far a user must reach to press the buttons or insert a cable. For guidelines,
see sections 307 (“Protruding Objects”) and 308 (“Reach Ranges”) of the 2010 ADA Standards for Accessible Design available at
http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.
Site preparation
The HCT101EU fits a standard one-gang European (EU) wall (junction) box or external wall box with mounting holes that are
60mm on center, or Extron Flex55 enclosures.
The HCT101MK fits a standard one-gang MK-type junction box or external wall box.
• The end user or installer must furnish the wall (junction) box. It is not included with the unit.
• Read any installation instructions and safety and regulatory guidelines that come with the wall box before installation.
• Protect the mounting surface to prevent damage.
To prepare the site:
1. For installation into a wall or furniture: Measure, mark, and carefully cut a hole in the mounting surface.
For all types of installations: Run cables to the junction box.
2. Secure the cables with a clamp for strain relief and so they do not slip back down into the wall or furniture.
3. Secure the box to the raceway, stud, wall, or furniture.
4. For wall mount installations, attach the metal mounting bracket to the junction box or external wall box.
For raceway installations, attach the metal mounting bracket to the junction box or external wall box and raceway.
a. Hold the mounting plate and feed the cables through the mounting plate.
e. Place the mounting bracket against the box, aligning the holes in the plate with the corresponding threaded holes on the
edges of the box.
f. Insert the provided screws into those holes, hold the metal mounting bracket to ensure it is aligned straight (visually
level), and tighten the screws to secure the plate to the mounting surface.
Step 3 — Connect AV, Interconnection, and Control Cables
1. Ground the HCT101 EU or HCT101MK transmitter (see Grounding on page12).
2. Connect AV sources to the input connectors (see AV Inputs on page10).
3. Use a shielded twisted pair cable to connect the transmitter to the receiver via the Output and Input RJ-45 connectors (see
Transmitter-Receiver Interconnection on page10).
4. Connect AV output devices (display, projector, or other device, and an amplifier or powered speakers) to the output
connectors (see AV Outputs on page11).
5. Cable the control ports on the receiver as desired for controlling AV devices and for communicating with the system via LAN
(see Control on page11).
Step 4 — Connect Power
Connect the power supply or power supplies to the HC400 Series system (see Power on page13), connect power cords, and
power on all the devices.
NOTE: The power supplies can be set on a tabletop, or mounted to a rack or furniture. Follow the mounting directions
included with each power supply or see the power supply installation guides available on the PS Series Power Supplies
page on the Extron website.
NOTE: For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the HCT must be
installed in a ULListed junction box. The end user or installer must furnish the junction box. It is not included with the unit.

6
HC 402 EU/MK • Setup Guide (Continued)
Step 5 — Configure Network Settings
You can configure the basic network settings in one of the following ways:
• Via front panel controls and the OSD menu — a quick method you can use whether or not you need to configure other
control settings (see Using the OSD menu to configure the AV settings on page8). This requires connection to a
display device.
• Via PCS software — a method that provides basic network configuration and is convenient when you are ready to use PCS
to configure AV settings. This requires a PC, software, and a LAN or USB connection.
• Via Toolbelt software — a method that allows you to configure additional connection settings and is convenient when you
want to configure additional device, password, system, and control port settings. This requires a PC, software, and a LAN
connection.
To configure network settings from the OSD menu:
From the Quick Setup menu:
• DHCP — Select and enter the DHCP Mode submenu and press the arrow buttons to turn DHCP on or off (default: off).
• IP address — Select and enter the IP Address submenu. Press the left or right arrow button to move between
octets. Press the up and down arrow buttons to change the value in the selected octet.
Default: 192.168.254.250.
From the Communication menu:
NOTE: Press and hold the Enter button for 10 seconds to edit settings in the Communication submenu.
• DHCP — Select and enter the DHCP Mode submenu and press the arrow buttons to turn DHCP on or off (default: off).
• IP address — Select and enter the IP Address submenu. Press the left or right arrow button to move between
and select octets. Press the up and down arrow buttons to change the value in the selected octet.
• Subnet mask — Select and enter the Subnet Mask submenu. Press the left or right arrow buttons to select an
octet of the subnet mask address. Press the up and down arrow buttons to adjust the value of the selected octet.
Default: 255.255.255.0.
• Gateway — Select and enter the Gateway submenu. Press the left or right arrow buttons to select an octet of the
gateway address. Press the up and down arrow buttons to adjust the value of the selected octet.
Default: 0.0.0.0.
To configure network settings using PCS:
1. Connect the PC and the LAN port of the HCR102 receiver (see LAN port on page12) to the same network.
Or
Connect the PC to the front panel Cong port of the HCR102 receiver using a USB type A male to USB mini-B male cable
(such as the Extron USB CFG cable).
2. Apply power to the PC and the HCR102.
3. Open PCS. You might need to open the application as an administrator by right-clicking the PCS icon and selecting Run as
administrator. PCS opens to the Device Discovery page. The Device Discovery process begins automatically. The
page displays a list of all Extron devices connected to the network as PCS detects them.
4. Using the MAC address, locate the desired device (HCR102) in the list.
5. In the row for the HCR102, click the Edit button in the IP Address
column. The Communication Settings dialog box opens,
displaying controls for network configuration.
6. Either select (enable) the Use DHCP checkbox to have the receiver
obtain an IP address automatically from a DHCP server, or enter the
static IP address for the unit in the IP Address field.
NOTE: When setting up DHCP during network configuration or if
using a host name instead of an IP address, the user must enter
a qualified host name (Username.HostName.Domain). For
example: somename.extron.com.
7. Configure the other items (device name, subnet mask, gateway
address, DNS server address) as needed.
8. Click Apply to save the configuration changes. Alternatively, you can
click Apply and Connect to save the configuration changes and
then establish a connection from the PCS software to the receiver to
configure AV settings or front panel lockout.
Figure 6. The PCS Communication Settings
Dialog Box

7
To configure network settings using Toolbelt:
1. Connect the PC that you will use for setup and the HCR102 receiver to the same network, and apply power to all devices.
For details on the LAN connection, see LAN on page12.
2. Start Toolbelt.
3. Start device discovery from within Toolbelt. Toolbelt displays a list of all Extron control devices connected to the network.
4. In Toolbelt, use the MAC address to locate the desired device (the HCR102) in the list and select it.
5. Use the Set IP feature in Toolbelt or use the Toolbelt Manage > Network Settings tab feature to enter the IP address and
subnet address, then configure other network settings as needed.
NOTE: When setting up DHCP during network configuration or if using a host name instead of an IP address, the user
must enter a qualified host name (Username.HostName.Domain). For example: somename.extron.com.
Step 6 — Configure AV Settings
The AV and scaling settings for the system can be configured via a host connection through the LAN port or the USB port using
PCS software or the on-screen display. Many settings can be configured using either method (OSD or PCS). Some settings are
available only in the PCS software.
To configure the AV settings using PCS software:
1. Install Extron PCS on a PC and start the program.
2. Connect the PC to the receiver via the rear panel LAN port (see figure 4, Non page 3) or the front panel Config USB
connector (see figure 2, Aon page 2). USB connection requires a user-provided USBA to USBmini-B cable.
3. Use the PCS program to set the output resolution and rate, configure EDID Minder, adjust the video color bit depth, or
monitor the signal and HDCP status, or other AV settings, as required. For details, see the HC400 Series User Guide, or
access the PCS Help File (press <F1> on the keyboard or click the ?button in the software and select Help File.
To configure the AV settings using the OSD and front panel buttons:
1. Connect an HDMI display device to the HDMI/CEC output connector on the HCR102.
2. Power on the receiver and the display device, if they are not already powered on.
3. Press the front panel Menu button on the HCR102 (see figure 2, F, or the image at right).
The OSD main menu appears on the display
(see the example below, at right).
The OSD menu system consists of the following menus:
• Quick Setup • Audio
• Picture Controls • Advanced
• Input • Communications
• Output
and one read-only information screen (Device Info).
4. Navigate through the menus and make adjustments.
a. Press the up and down arrow navigation buttons
(see H) to navigate to and highlight the desired menu or
submenu.
e. Press the Enter button (G) or right arrow button
to access submenu items for the selected submenu (see
Using the OSD menu to configure the AV settings for
information about the contents of each submenu).
f. Press the up and down arrow buttons to navigate to
and highlight submenu items.
g. Press the Enter or right arrow button to adjust a
submenu item.
NOTE: The OSD times out and closes after one minute if no
buttons are pressed.
HCR 102
MENU
ENTER
HOLD FOR 720p/1080p
Navigation buttons
Enter button
Menu button
Quick Setup
Picture Controls
Input
Output
Audio
Advanced
Communications
Device Info
P
icture
C
ontrol
s
I
nput
O
utput
A
udio
Ad
vance
d
C
ommunications
D
evice In
f
o
IP Address
192 . 168 .254 . 250
DHCP Mode
Off
Test Pattern
Crop
Audio Mute
On
Output Resolution
1920x1200 @60Hz
Input 1: EDID
1920x1080 @60Hz
Input 1: Input Format
HDMI
Quick Setup
1920x1200 @ 60Hz
Output Resolution
1920x1080 @ 60Hz
Input 1
FW 2.03
192.168.254.250
HCR 102
Extron Electronics

8
HC 402 EU/MK • Setup Guide (Continued)
Using the OSD menu to configure the AV settings
• Use the Quick Setup submenu to set input EDID settings, set output resolution, mute audio, activate video test patterns,
enable or disable DHCP, and set the IP address.
• Use the Picture Controls submenu to view the image position and size.
• Use the Input submenu to set the input format for digital inputs, set horizontal and vertical start values, set the total pixels
and phase, set HDCP authorization, and set the EDID for the current input.
• Use the Output submenu to set output resolution, HDMI output format, and HDCP notification.
• Use the Audio submenu to mute audio, set the audio input format (see table below) for the selected input, set program audio
volume, and set audio output format (stereo, mono).
Audio Input Format Details
None Mutes all audio for selected input. Sets “No Audio” EDID.
Analog Sets the selected input to analog (default for input 1). Sets “No Audio” EDID.
LPCM-2Ch Sets the selected input to LPCM-2Ch digital audio (default for input 2). Sets 2Ch audio EDID.
Multi-Ch Sets the selected input to Multi-Ch digital audio. Sets Multi-Ch audio EDID.
LPCM-2Ch auto Sets the selected input to prioritize digital audio (default for inputs 3-4). Analog audio is passed when
digital audio is not present. Sets 2Ch audio EDID.
Multi-Ch auto Sets the selected input to prioritize digital audio. Analog audio is passed when digital audio is not
present. Sets Multi-Ch audio EDID.
• Use the Advanced submenu to select a test pattern, set the screen saver, set the aspect ratio, configure auto switching, and
reset the device to factory defaults.
• Use the Communication submenu to view the device MAC address, DHCP status, the current IP address and subnet mask,
and gateway.
NOTE: Press and hold the Enter button for 10 seconds to edit settings in the Communication submenu.
• Use the Device Info screen to view the device name, firmware build, temperature, input and output information, and
detected display. This screen is read-only.
See the HC400 Series User Guide for details about the menus and available settings, and for a list of output scaler rates.
Step 7 — Configure the Control Settings
To use the COM, IR, or digital I/O ports on the receiver, you must configure them. Also, CEC control of the output device can be
customized during configuration with Global Configurator.
The basic steps are outlined below in the recommended order.
NOTE: See the Toolbelt Help File or Global Configurator Help File, and GUI Designer Help File as needed for step-by-step
instructions and detailed information. The help file for GC includes an introduction to the software and how to start a project
and configuration.
1. Using GC, create a new GCPro or GCPlus project and configure the receiver and other IP Link Pro devices. The
configuration tells the receiver:
• How its control ports function • What to monitor
• How to control other products • When to do things
• Which touchpanels to interact with • Whom to notify, how, and under what circumstances
a. Configure the control ports on the receiver.
• Select device drivers and link them to each serial, IR, or Ethernet port.
• Select settings (serial protocol or digital I/O settings) as needed.
• Configure CEC controls, if desired
b. Set up monitors, schedules, macros, timers, and local variables.
c. Add any optional touchpanels and set them up:
• Create the GUI configuration for the touchpanels and add it to the project.
• Program functions, monitors, or schedules to the touchpanels and their buttons.
4. Save and build the project.
5. Upload the system configuration to the HCR102 receiver.

9
Step 8 — Test and Troubleshoot the System
1. Test the system. See the HC400 Series User Guide for an outline of the system testing procedure.
2. Make adjustments to wiring or configuration as needed.
Step 9 — Mount the HCT101EU or HCT101MK
NOTE: Extron recommends taking
safety precautions to avoid electrostatic
discharge issues during installation.
Before mounting the transmitter, ensure that
all device cables have been fed through
the wall or furniture and mounting box.
To mount the transmitter (see figures 7 and
8 at right):
1. Disconnect power at the source from
all devices in the system.
2. Align the wallplate or frame with
the metal mounting bracket. (The
mounting bracket was attached to
the wall box in Site preparation on
page5.)
3. Ensure that the cables and grounding
wire are connected to the rear panel
(see Cabling starting on page10,
especially Grounding on page12).
4. Secure the transmitter to the mounting
bracket: Insert the cabled HCT module
through the opening in the frame and
firmly press it into place so its side
tabs snap into the mounting bracket.
5. Reconnect power to all devices.
e
HDMI IN
Wall Box
Frame
Metal Mounting Bracket
HCT 101 EU
Figure 7. Mounting the HCT 101 EU to an EU Wall Box
e
HDMI IN
MK Wall Box
Wall
Metal Mounting Bracket
Frame
HCT 101 MK
Figure 8. Mounting the HCT 101 MK to an MK Wall Box.

10
HC 402 EU/MK • Setup Guide (Continued)
Cabling
Attach cables using the wiring diagrams on the following pages as a guide. Full details are available in the HC400 Series User Guide.
AV Inputs
Digital AV input
For HDMI video and for digital audio embedded within HDMI signals:
1. Connect a digital video source device to any HDMI input connector on the
transmitter or receiver (see figure 3 and figure 4, Din Rear and Side Panel
Features on page3).
2. To secure a cable to the unit, attach an Extron LockIt®bracket to the receiver and
secure it to the cable with a zip tie.
a. Plug the HDMI cable into the panel connection (see aat right).
c. Loosen the HDMI connection mounting screw from the panel enough to allow the
LockIt lacing bracket to be placed over it (b). The screw does not have to be
removed.
d. Place the LockIt lacing bracket on the screw and against the connector (c), then
tighten the screw (d) to secure the bracket.
e. Loosely place the included tie wrap around the connector and the LockIt lacing
bracket as shown (e).
f. While holding the connector securely against the lacing bracket, tighten the tie
wrap, then remove any excess length.
Complete details on LockIt installation are available in the LockIt HDMI Cable Lacing
Bracket Installation Guide.
Transmitter-Receiver Interconnection
Connect the Out port of the transmitter (figure 3, E) to the In port of the receiver (F) using a
shielded twisted pair CATxcable of up to 230 feet (70 m), as shown in figure 1 on page 1.
Terminate the cable with shielded RJ-45 connectors using the TIA/EIA-T568B wiring standard
at both ends, as shown at right.
ATTENTION:
• Do not connect this port to a computer data network or a telecommunications network.
• Veuillez ne pas connecter ce port à un réseau de données informatiques ou à un
réseau de télécommunications.
• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable.
• N’utilisez pas le câble AV Skew-Free UTP version améliorée UTP23SF-4 d’Extron ou
le câble STP201.
For optimal performance, Extron highly recommends the following:
• Use the TIA/EIA-T568B wiring standard for terminating all STP cables with RJ-45 connectors.
• Use shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable bandwidth of 400 MHz.
• Use shielded RJ-45 plugs to terminate the cable.
• Overall transmission distance capabilities vary depending on the number of patches used. If possible, limit the number of
patches to 2 total.
• If patches must be used in the system, Extron recommends shielded CAT6 (or better) patch cables.
3
a
b
c
d
e
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA-T568B
Insert twisted
pair wires.
12345678
Pins:
• Limit the use of more than two pass-through points, which may include patch points, punch down connectors, couplers, and
power injectors. If these pass-through points are required, use shielded couplers and punch down connectors.
NOTE: When using shielded twisted pair cable in bundles or conduits, consider the following:
• Do not exceed 40% fill capacity in conduits.
• Do not comb the cable for the first 20 meters, where cables are straightened, aligned, and secured in tight bundles.
• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
• Separate twisted pair cables from AC power cables.