Extron electronics MTP 1500RL 15HD A SEQ User manual

This guide provides basic instructions for an experienced installer to set up and operate any of
the Extron®MTP 1500RL 15HD RS series of extended mini twisted pair receivers; the
MTP 1500RL 15HD RS and the MTP 1500RL 15HD RS SEQ (model shown above). For full
details, refer to the MTP 1500RL 15HD RS Series User’s Manual, available at www.extron.com.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources
and mount the MTP 1500RL 15HD receiver as required.
Step 2 — Connect input
Connect the RJ-45 cable from an MTP transmitter
to the Input port on the MTP 1500RL 15HD receiver.
Terminate the cable as shown on the right, using the
same standard (A or B) at both ends.
Step 3 — Connect outputs
Attach the applicable output cables (video, RS-232, and buffered output).
a. High resolution video output — Connect a suitable display device to the 15-pin HD
connector (RGB).
b. RS-232 connector — Connect an RS-232 compatible device into the 3-pole captive screw
connector (wired as below) for bidirectional or unidirectional communication up to
1,000 feet (maximum).
Ground
Tx
Rx
Gnd
Receive
Transmit
Connected RS-232
Device Pins MTP Reciever
Pins
c. Buffered output — Connect up to 8 daisy-chained MTP receivers to this RJ-45 connector.
Step 4 — Receiver DIP switches
•H sync (H+) and V sync (V+) switches — Set these switches up (On)
for positive sync or down for negative sync.
•Composite Sync, (SOG), and Video switches — Set these switches as
shown in the table at right to output the indicated format.
•End Unit switch — Set this switch up if either of the
following is true:
a. The receiver being configured is the only
receiver connected to the transmitter.
b. The receiver being configured is the last
receiver in a daisy-chained system.
•BI-232 switch — Set this up (On) for bidirectional
or down for unidirectional communication.
Setup Guide — MTP 1500RL 15HD RS Series
MTP 1500RL SERIES
RGB
PEAKING
LEVEL
DELAY
RED
GREEN
BLUE
SELECT
ADJUST
INPUT BUFFERED OUTPUT
POWER
12V
1.0A MAX
MTP 1500RL 15HD RS SEQ
MTP
RS-232
RxTx
OUTPUT
MTP
MIN/MAX
ON
H + V + CSYNC
SOG VIDEO END BI-232
MTP
MTP
(Continued on reverse side)
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
NOTE If you are using Enhanced
Skew-Free
™
A/V cable, use the
TIA/EIA T568A standard only.
Green
White-orange
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
White-blue
Green
White-brown
Brown
Blue Blue
Insert
TP Wires
Pins:
12345678
Format
Output
Format C Sync SOG Video
RGBHV
RGBS
RGsB
Component*
S-video*
Composite*
* Input video format must match.
ON
H + V + CSYNC
SOG VIDEO END BI-232

Step 5 — Power
Plug the included external 12 VDC power supply into the
2-pole captive screw connector. Wire the connector as shown.
Step 6 — Peaking and Level
Image sharpness is adjusted with the Peaking control. Increased
peaking compensates for mid- and high-frequency detail loss.
The LED lights red when minimum (zero) and maximum
peaking is reached.
Image brightness is adjusted using the Level control.
View the image and adjust either control for the best image quality.
Step 7 — Skew compensation (SEQ model only)
Pair skew can be measured with test equipment or by viewing a crosshatch test pattern.
The SEQ receivers have built-in skew compensation capabilities. Adjust the equalization as
follows:
a. Zero the skew delay for red, green, and blue by using a
Tweeker or small screwdriver to press and hold the Select
button for 3 seconds. When the Red, Green, and Blue LEDs
all go out, release the Select button.
b. Use UTP cable test equipment or examine the displayed image
to determine which video signal, red, green, or blue, is shifted furthest to the right.
c. Adjust the furthest left video signal by using a Tweeker or screwdriver to press
and release the Select button until the LED for the left-shifted color lights.
d. Slowly rotate the Adjust control clockwise until the shifted color is properly aligned.
e. Repeat steps 6c and 6d to align the third color if needed.
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
Setup Guide — MTP 1500RL 15HD RS Series, cont’d
DELAY
RED
GREEN
BLUE
SELECT
ADJUST
Po wer Supply
Output Cord
SECTION A–A
Ridges
Smooth
A A
Captive
Screw
Connector
Tie Wrap
3"
16 (5 mm) Max.
INPUT
Tx Rx
RS-232
MONITOR
POWER
12V
.5AMAX
OUTPUT
CABLE
NORM LONG
MTPT VGA RS
POWER
12V
1.0AMAX
RS-232
Rx
Tx
OUTPUT
INPUT BUFFEREDOUTPUT
MTP1500RL 15HD RS SEQ
H+
V+
CSYNC
SOG
VIDEO
END
BI-232
ON
MTP
MTP
POWER
12V
1.0AMAX
RS-232
Rx
Tx
OUTPUT
INPUTBUFFEREDOUTPUT
MTP1500RL 15HD RS SEQ
H+
V+
CSYNC
SOG
VIDEO
END
BI-232
ON
MTP
MTP
PC
Flat Panel
Display
Flat Panel
Display
Extron
MTP 1500RL 15HD RS SEQ
Mini Tw isted Pair Receiver
with Loop-T hrough and Skew EQ
500 ft UTP Cable
(CAT 5/5e/6)
Extron
MTP T 15HD RS
Mini Twisted Pair
Transmitter
RS-232
RS-232
RGBHV
RGBHV
500 ft UTP Cable
(CAT 5/5e/6)
RS-232
RGBHV
Extron
MTP 1500RL 15HD RS SEQ
Mini Tw isted Pair Receiver
with Loop-T hrough and Skew EQ
Example of a typical MTP 1500RL 15HD RS SEQ application
68-1555-50
Rev. A
08 09
© 2009 Extron Electronics. All rights reserved.
RGB
PEAKING
LEVEL
MIN/MAX