Extron electronics SW RGBHV Series User manual

This guide provides quick start instructions for an experienced installer
to set up and operate the SW RGBHV and SW RGBHV A
switchers.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources
and mount the switcher as required.
Step 2 — Inputs
• Connectupto2,4or6RGBHV,RGBS,
RGsB,orRsGsBsvideoorcomponent
video inputs to the Input connectors.
• Audio models —Connectupto2,
4or6stereoormonoaudioinputs
to the 5-pin
captive screw
connectors.
Step 3 — Outputs
• ConnectanRGBHV,RGBS,RGsB,orRsGsBsvideoorcomponentvideodisplayor
other device to the Output connectors. Make connections as shown for step 3.
• Audio models —Connectabalancedorunbalancedstereoaudioormonoaudio
device to the 5-pin captive screw connector.
CConnect the sleeves to ground (Gnd). Connecting the sleeve to a negative (-) terminal
will damage the audio output circuits.
Step 4 — Remote port
Connectahostdevice,suchasacomputerortouch
panelcontrolviaRS-232,OR connect a remote contact
closure device to the switcher
via the 9-pin D connector for
remote control of the switcher.
To command a switch under
contactclosurecontrol,
momentarilyshortaninput’s
pin on the remote connector to
ground(theswitchermustbein
normal [manual] mode).
NFor complete descriptions of remote control of the switcher using the applicable Simple
Instruction Set (SIS™) commands and/or the Universal Switcher Control Program, refer to
the full SWRGBHVSwitchersUser’sManual, available at www.extron.com.
Step 5 — Power
PlugastandardIECpowercordbetweentheswitcher’spowerconnectoranda100VACto
240VAC,50or60Hzpowersource.
Operation
Switch mode
SettherearpanelswitchtoAutoforautoswitchmode(theswitcherautomatically
switchestothehighest-numberedinputwithasyncsignalpresent)orNormalfor
manual switch mode. The front panel Auto Switch Active LED lights when the
switcher is in autoswitch mode.
Switch inputs in normal switch mode
Pressandreleasethedesiredinputbutton.
Adjust audio level (audio models)
You can set the input level of audio gain or attenuation via the front panel or the Remote port
tobecompatiblewithawiderangeoflinelevelsources.Individualinputaudiolevelscanbe
adjustedsothatthereisnonoticeablevolumedifferenceamongsources.Thisfunctionalso
eliminatestheneedforseparatepreampsorattenuators,whenusedwithprofessional(higher
line level) and consumer (lower line level) audio equipment.
Adjust the audio from the front panel as follows:
1. Pressandreleasethedesiredinputbutton.
2. PressandholdtheAudioConf./SavebuttonuntiltheAudioConf./
SaveLEDbeginstoblink.Theapproximatelevelisindicatedbythe
inputLEDsandthepolaritybythe±dBLEDs.
NThe input LEDs display the approximate level of attenuation.
The +dB LED indicates the level is gain (positive).
The - dB LED indicates the level is attenuation (negative).
For details about reading the displayed value, refer to the
full SWRGBHVSwitchersUser’sManual, available at
www.extron.com.
3. Press and release the >and <buttonstoincreaseanddecreasetheaudiolevelby1dB
perpushofthebutton,orpressandholdthebuttonstoincreaseordecreasethelevel
by3dBpersecond.
4. PressandreleasetheAudioConf./Savebuttontoexit.TheAudio
Conf./SaveLEDgoesout.
Do not tin the wires!
Unbalanced Stereo Output Balanced Stereo Output
Ring
Sleeve(s)
Tip
Tip
Ring
Sleeve(s)
Tip
Tip
NO GROUND HERE.
NO GROUND HERE.
L R
L R
Unbalanced Stereo Input
Balanced Stereo Input
L R
L R
Ring
Sleeve (s)
Tip
Sleeve
Tip
Sleeve
Tip
Tip
Ring
Do not tin the wires!
Setup Guide — SW RGBHV Series Switchers
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FA X
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
©2009ExtronElectronics.Allrightsreserved.
68-648-50
Rev. A
04 09
Setup Guide — SW RGBHV Series Switchers
CONF/SAVE
B
Press
and hold.
Conf/Save blinks.
Release the button.
2
6
5
4
32
1
-dB +dB
3
Press Press
CONF/SAVE
Press
and release.
4
G
RGBHV
RGBS
RGsB,
RsGsBs,
Component
BH/HV V
RG BH/HV V
RG BH/HV V
Pin RS-232 Contact
closure
Function
1 — In#1 Input#1
2 TX
—
— Transmit data (-)
3 RX Receive data (+)
4 — In#2 Input#2
5 Gnd
RS-232 Protocol:
9600 Baud, 8, N, 1
Gnd Signal ground
6 — In#3
In#4
In #5
In#6
Input#3
Input#6
Input#4
Input #5
7 —
8 —
—
Female
51
96
AUTO
MANUAL
1
Press
and release.
1