Crestron infiNET CLW-SLVS1RF User manual

Crestron CLW-SW1/4RF,
CLW-SWS1/4RF, CLW-SLVS1RF
infiNET™ Switches
Operations Guide

This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2007 Crestron Electronics, Inc.

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
Contents
infiNET™ Switches: CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF 1
Introduction ...............................................................................................................................1
Features and Functions................................................................................................1
Specifications ..............................................................................................................3
Physical Description....................................................................................................4
Industry Compliance ...................................................................................................7
Acquire the Switch on the infiNET Network.............................................................................8
Operation .................................................................................................................................10
Identity Code ...........................................................................................................................13
Programming Software............................................................................................................22
Earliest Version Software Requirements for the PC ................................................. 22
Programming with D3 Pro.........................................................................................23
Programming with SIMPL Windows ........................................................................23
Example Program ......................................................................................................25
Uploading and Upgrading........................................................................................................ 26
Establishing Communication..................................................................................... 26
Programs and Firmware ............................................................................................ 26
Program Checks ........................................................................................................ 27
Problem Solving ......................................................................................................................28
Troubleshooting......................................................................................................... 28
Bootloader .................................................................................................................29
Reference Documents................................................................................................30
Further Inquiries ........................................................................................................ 30
Future Updates .......................................................................................................... 30
Return and Warranty Policies ..................................................................................................31
Merchandise Returns / Repair Service ...................................................................... 31
CRESTRON Limited Warranty.................................................................................31
Operations Guide - DOC. 6397A Contents •i

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
infiNET™ Switches:
CLW-SW1/4RF, -SWS1/4RF,
-SLVS1RF
Introduction
Features and Functions
The CLW-SW1RF (-SW1RF) one-button switch and CLW-SW4RF (-SW4RF)
four-button switch are stand-alone wall box switches that can also act as wireless
infiNET™ devices that report to a Crestron®control processor via a Crestron
infiNET wireless gateway.
infiNET Switches Functional Summary
• Two-way infiNET switches
⇒
⇒
⇒
⇒
2.4 GHz infiNET mesh network technology
Range up to 150 feet indoors, or 250 ft outdoors (subject to site-
specific conditions)
Range may be increased with the use of additional infiNET devices
or C2N-MNETRPT repeaters
“Wi-Fi” friendly operating frequency to avoid interference
• One-button and four-button configurations available in white, black,
and almond
• Can be ordered with custom-engraved buttons
• Can operate as a local load control or infiNET keypad.
These switches can be operated with a user-adjustable delay up to 10 minutes and 55
seconds. For more information, refer to “Operation” on page 10 for more
information.
These infiNET switches are a part of Crestron’s line of lighting products using
infiNET mesh network technology. infiNET technology is “Wi-Fi” friendly and
provides fault tolerance and increased effective signal strength as network devices
are added.
As an infiNET device, these switches communicate with a Crestron control system
via a C2N-MNETGW infiNET Gateway. Up to 30 infiNET devices (including
C2N-MNETRPT infiNET Repeaters) can communicate with one C2N-MNETGW
Operations Guide - DOC. 6397A infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF •1

infiNET™ Switches Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF
infiNET Gateway and, if more devices are needed, more C2N-MNETGW gateways
may be added to a Cresnet®network.
Crestron infiNET switches operate on the 2.4 GHz “ISM band” (2400 MHz to
2483.6 MHz) at 10 mW. The output power of these devices allow RF signals to
travel approximately 150 feet indoors and 250 feet outdoors (subject to site-specific
conditions) without the use of repeaters or other infiNET devices. The range is
dependent on construction of the building, obstructions, and RF interference from
other devices. The location of the switch is an important factor in determining RF
performance. Adding more infiNET devices or repeaters to the network effectively
increases the range, strength, and reliability of the network.
The -SW1RF and -SW4RF feature a three-position mode selection switch. Refer to
“Operation” on page 10 for more information. In the absence of control system
communications, the switch can still be used to control the attached load.
The CLW-SWS1RF (-SWS1RF) and CLW-SWS4RF (-SWS4RF) are similar to the
-SW1RF and -SW4RF (respectively) with the added capability of working with one
or more slave units (CLW-SLVS1RF) in a multi-switch / single circuit application.
For more information, refer to the latest version of the infiNET Switches Installation
Guide (Doc. 6293) which is available from the Crestron website
(www.crestron.com/manuals).
The CLW-SLVS1RF (-SLVS1RF) is a slave unit that when used in conjunction with
the -SWS1RF or -SWS4RF acts as an additional switch control point in a multi-
switch / single circuit application. It does not connect to an infiNET system and
cannot be used without a -SWS1RF or -SWS4RF. The -SLVS1RF does not have a
mode selection switch. It can only be programmed when used in conjunction with a
-SWS4RF (refer to the SIMPL™ Windows®help file). Otherwise, it will emulate the
RUN mode of the -SWS1RF (even if connected to a -SWS4RF) unless the mode
selection switch of the master is set to “OFF”.
These switches can be ordered with custom engraved buttons already installed by
Crestron. Engraved buttons cannot be installed or changed in the field. Contact
Crestron for more information.
These switches are available in a variety of colors and textures. The table below
shows the availability.
Available Colors/Textures
COLOR/
TEXTURE
MODEL NUMBER
SUFFIX
MATCHING FACEPLATE
(Lutron®Part Number Shown
White W Not Applicable
Smooth White W-S CW-1-WH
Almond A CW-1-LA
Smooth
Almond
A-S CW-1-LA
Black B Not Applicable
Smooth Black B-S CW-1-BL
For installation instructions, refer to the latest version of the infiNET Switches
Installation Guide (Doc. 6293), which is available from the Crestron website.
2 •infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF Operations Guide - DOC. 6397A

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
Specifications
Following are specifications for the -SW1RF, -SW4RF, -SWS1RF, -SWS4RF, and
-SLVS1RF.
CLW-SW1/4RF, CLW-SWS1/4RF, & CLW-SLVS1RF Specifications
SPECIFICATION DETAILS
Power Requirements Line Power, 120 VAC, 60 Hz
Operating Frequency 2400 MHz to 2483.6 MHz
(802.15.4 compliant)
RF Output Power 10 mW
Operating Ranges¹
Typical Distance
Indoors (without repeater)
Typical Distance Outdoors
150 ft
250 ft, subject to site-specific conditions
Default MNET ID -SW1RF/-SW4RF: 01/01
-SWS1RF/-SWS4RF: 01/01
Switch Type Single-Pole, Single-Throw
Load Type Incandescent, Tungsten-Halogen,
Fluorescent / High Intensity Discharge (HID),
Electronic Low Voltage, Magnetic Low
Voltage, Neon / Cold Cathode, Ceiling Fan
2-Series Control System Update
File2,3
Version 3.154 or later
Load Ratings4
Incandescent / Tungsten-
Halogen
-SW1RF/-SW4RF: 1000W
-SWS1RF/-SWS4RF: 1000W
-SLVS1RF: N/A
Magnetic Low Voltage5-SW1RF/-SW4RF: 1000VA/750W
-SWS1RF/-SWS4RF: 1000VA/750W
-SLVS1RF: N/A
Neon / Cold Cathode5-SW1RF/-SW4RF: 1000VA/750W
-SWS1RF/-SWS4RF: 1000VA/750W
-SLVS1RF: N/A
Electronic Low Voltage -SW1RF/-SW4RF: 1000W
-SWS1RF/-SWS4RF: 1000W
-SLVS1RF: N/A
Ceiling Fan -SW1RF/-SW4RF: 3A
-SWS1RF/-SWS4RF: 3A
-SLVS1RF: N/A
Minimum Load 40W / 0.5A
Operating Temperature and
Humidity
32°F to 104°F (0°C to 40°C)
10 to 90% Relative Humidity
(Non-Condensing)
Dimensions and Weight -SW1RF/-SW4RF and
-SWS1RF/-SWS4RF:
Height: 4.13 in (10.48 cm)
Width: 2.38 in (6.03 cm)
Depth: 1.88 in (4.77 cm)
Weight: 4.9 oz (0.67 kg)
(Continued on following page)
Operations Guide - DOC. 6397A infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF •3

infiNET™ Switches Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF
CLW-SW1/4RF, CLW-SWS1/4RF, & CLW-SLVS1RF Specifications (continued)
SPECIFICATION DETAILS
Dimensions and Weight
(continued)
-SLVS1RF:
Height: 4.13 in (10.48 cm)
Width: 1.75 in (4.45 cm)
Depth: 1.88 in (4.77 cm)
Weight: 3.6 oz (0.50 kg)
1. The range is dependent on its placement and the building in which it is used. The construction of the
building, obstructions, and RF interference from other devices are factors determining the effective
range of the unit.
2. The latest software versions can be obtained from the Crestron website. Refer to the NOTE
following these footnotes.
3. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest Crestron Product
Catalog for a complete list of 2-Series control systems.
4. Refer to Derating Charts for Multigang Installations in the latest version of the infiNET Switches
Installation Guide (Doc. 6293) which is available from the Crestron website.
5. VA ratings are for input power to the transformer. If you do not know the input power requirement
of the transformer, use the bulb’s wattage rating to determine proper rating.
NOTE: Crestron software and any files on the website are for Authorized Crestron
dealers and Crestron Authorized Independent Programmers (CAIP) only. New users
may be required to register to obtain access to certain areas of the site (including the
FTP site).
Physical Description
The -SW1RF and -SWS1RF have a light emitting diode (LED) with adjustable
brightness (via Crestron programming software), a rocker button, and a three-
position mode selection switch as shown in the following diagrams. The button may
be pushed at the top or bottom to perform certain functions. Pushing the button in the
middle does not do anything. The function of the pushbutton is determined by the
position of the mode selection switch. For more information, refer to “Operation” on
page 10.
Parts of CLW-SW1RF and -SWS1RF
Button
Mode Selection Switch
RUN SET OFF
4 •infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF Operations Guide - DOC. 6397A

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
Physical View of CLW-SW1RF/-SWS1RF (Clockwise from Top; Top, Side, and Front)
1.75 in
(4.45 cm)
2.38 in
(6.03 cm)
3.28 in
(8.32 cm)
3.81 in
(9.68 cm)
4.13 in
(10.48 cm)
1.88 in
(4.77 cm)
2.70 in
(6.86 cm)
1.50 in
(3.81 cm)
OFFSETRUN
The -SW4RF and -SWS4RF have a light emitting diode (LED) with adjustable
brightness (via Crestron programming software), four pushbuttons, and a three-
position mode selection switch as shown in the following diagrams. Each of the
buttons may be pushed to perform certain functions. The function of each pushbutton
is determined by the position of the mode selection switch. For more information,
refer to “Operation” on page 10.
Parts of CLW-SW4RF, -SWS4RF
Button 2
Mode Selection Switch
Button 4Button 3
Button 1
RUN SET OFF
Operations Guide - DOC. 6397A infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF •5

infiNET™ Switches Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF
Physical View of CLW-SW4RF/-SWS4RF (Clockwise from Top; Top, Side, and Front)
RUN SET OFF
1.75 in
(4.45 cm)
2.38 in
(6.03 cm)
3.28 in
(8.32 cm)
3.81 in
(9.68 cm)
4.13 in
(10.48 cm)
1.88 in
(4.77 cm)
2.70 in
(6.86 cm)
1.50 in
(3.81 cm)
The -SLVS1RF is similar in appearance to the -SW1RF and -SWS1RF but does not
have the three-position mode selection switch. The brightness of the LED on the
-SLVS1RF is not programmable.
Physical View of CLW-SLVS1RF (Clockwise from Top; Top, Side, and Front)
1.75 in
(4.45 cm)
3.81 in
(9.68 cm)
4.13 in
(10.48 cm)
3.28 in
(8.32 cm)
1.88 in
(4.77 cm)
2.70 in
(6.86 cm)
1.50 in
(3.81 cm)
The -SW1RF, -SW4RF, -SWS1RF, -SWS4RF, and -SLVS1RF mount in a standard
wallbox and are covered using a decorative faceplate (not included). All line voltage
connections are made at the rear of the switch.
6 •infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF Operations Guide - DOC. 6397A

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
Left to Right, CLW-SW1RF/-SWS1RF, CLW-SW4RF/-SWS4RF, and
CLW-SLVS1RF; Shown in White
Industry Compliance
This product is Listed to applicable UL Standards and requirements by Underwriters
Laboratories Inc.
E239013
FCC ID: EROCWD1011
Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference
that may cause undesired operation.
Warning (Part 15.21)
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
RF Exposure (OET Bulletin 65)
To comply with FCC’s RF exposure limits for general population / uncontrolled
exposure, this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
Industry Canada Statement
The term “IC” before the certification/registration number only signifies that the
Industry Canada technical specifications were met
IC: 5683A- CWD1011
Operations Guide - DOC. 6397A infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF •7

infiNET™ Switches Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF
Acquire the Switch on the infiNET Network
Before an infiNET device can be used on an infiNET network, it must first be
acquired to a C2N-MNETGW gateway that is connected to a Cresnet network.
NOTE: The -SW1RF, -SW4RF, -SWS1RF, and -SWS4RF can also work as stand-
alone wall box switches without being acquired by a C2N-MNETGW.
NOTE: A switch can be acquired to only one gateway.
Acquire the Switch To acquire a -SW1RF/-SW4RF/-SWS1RF/-SWS4RF to a C2N-MNETGW, perform
the following:
1. Put the C2N-MNETGW in the Acquire mode, from the unit itself or from
Crestron Toolbox, as described in the latest revision of the C2N-MNETGW
Operations Guide (Doc. 6317) which is available from the Crestron website
or the Crestron Toolbox help file.
NOTE: In an environment where multiple gateways are installed, only one
gateway should be in the Acquire mode at a time.
2. Place the -SW1RF/-SW4RF/-SWS1RF/-SWS4RF into the Acquire mode by
doing the following:
a. Move the mode selection switch (located under the LED) to the
“OFF” position.
b. Press and hold the top or bottom of the button on the -SW1RF/
-SWS1RF or any button on the -SW4RF/-SWS4RF.
c. While holding the button, slide the mode selection switch to the
“RUN” position.
d. Hold the button for approximately five seconds until the LED
flashes HIGH once. Immediately release the button after the LED
blinks to start the switch’s Acquire mode.
NOTE: The LED can flash HIGH or LOW. Refer to “LED Behavior” on
page 11 for more information.
NOTE: Holding the button for a significant time after the first flash may
enter other modes. If this is not desired, return the mode selection switch to
the “OFF” position without releasing the button and repeat step 2.
After approximately ten seconds, the LED will start to blink slowly and the
switch will attempt to acquire with a C2N-MNETGW that is in the Acquire
mode. The device is acquired when the LED stops blinking and lights at the
LOW setting. After being acquired, the device will exit the Acquire mode.
The switch will be acquired on the C2N-MNETGW with an MNET ID
value of 01. If the switch was previously acquired on another infiNET
network, the switch will be acquired on the C2N-MNETGW with its
previous MNET ID.
8 •infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF Operations Guide - DOC. 6397A

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
3. Take the C2N-MNETGW out of the Acquire mode once all devices have
been acquired. Refer to the latest revision of the C2N-MNETGW
Operations Guide (Doc. 6317), which is available from the Crestron
website.
To communicate with the control system program, an MNET ID value
between 03 and 20 must be assigned to the switch. For information on
assigning MNET ID values, refer to “Identity Code” on page 13.
Remove Gateway
Information from a
Switch
In some rare cases, it might be desirable to release a switch from a gateway. If a
switch is to be released from a gateway, the gateway information must be cleared
from the switch’s memory.
To clear a switch’s gateway information:
1. Move the mode selection switch (located under the LED) to the “OFF”
position.
2. Press and hold the top or bottom of the button on the -SW1RF/-SWS1RF or
any button on the -SW4RF/-SWS4RF.
3. While holding the button, slide the mode selection switch to the “RUN”
position.
4. Hold the button for approximately ten seconds until the LED flashes twice.
Immediately release the button after the LED flashes twice to clear the
switch’s gateway information. Reacquire the switch if desired.
A switch can also be released from a gateway using Toolbox. Refer to the latest
revision of the C2N-MNETGW Operations Guide (Doc. 6317) or the Crestron
Toolbox help file for instructions.
Operations Guide - DOC. 6397A infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF •9

infiNET™ Switches Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF
Operation
NOTE: The device may be warm to the touch during operation. This is normal.
Mode Selection Switch These switches use a three-position mode selection switch to set the mode of
operation.
• OFF
When the mode selection switch is in the “OFF” position, the pushbutton(s)
will not have any function and the load is disconnected from the power
source. This must be used when changing light bulbs to ensure that the load
is fully disconnected from power. Slave devices that are connected to the
switch will not have any function when the Master’s mode selection switch is
in the “OFF” position.
• RUN
When the switch is in the “RUN” position, it is operating in the RUN mode.
This is the normal operating mode of the switch. The RUN mode is used to
turn the load on and off. If a delay time is set, the switch will turn off the
load after the set delay time. For information on setting a delay time, refer to
“SET” below.
Refer to the following table for a list of available functions when the switch
is operating in the RUN mode.
NOTE: If the behavior of the -SW4RF/-SWS4RF has not been changed in
SIMPL™ Windows®, SystemBuilder™ or D3 Pro™, the only button that
will perform any function is Button 1. All of the other buttons are
programmable.
RUN Mode Button Functions
FUNCTION -SW1RF/
-SWS1RF/
-SLVS1RF
BUTTON PRESS
-SW4RF/-SWS4RF
BUTTON PRESS
Turn on load. Tap the Top button. Tap Button 1.
Turn off load with
delay.1,2
Tap the Bottom button. Tap Button 1.
Cancel delayed-
off timer (if load
was already on
and timer was
running).
Tap the Top button. Tap Button 1.
Turn off load
immediately
Double-tap the Bottom
button.
Double-tap Button 1.
1. If delay is set to 0 seconds, the load will turn off immediately.
2. If the switch was in the middle of a delay, pressing the button will cancel the delay and turn
off the load immediately
10 •infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF Operations Guide - DOC. 6397A

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
• SET
When the mode selection switch is in the “SET” position, it is operating in
the SET mode. The LED will blink to indicate that the switch is in the SET
mode. Refer to the following table for a list of available functions when the
switch is operating in this mode.
NOTE: The SET mode is only intended for adjusting the delay time. Under
normal operation, the mode selection switch should be in the “RUN”
position.
SET Mode Button Functions
FUNCTION -SW1RF/-SWS1RF
BUTTON PRESS
-SW4RF/-SWS4RF
BUTTON PRESS
Set the delay
time to zero
seconds.
Double-tap the Bottom
button.
Double-tap the Button 1.
Set the delay
time.*
Press and hold the
Bottom button for the
desired amount of delay.
Upon release, the LED
will flash to confirm.
Press and hold Button 1
for the desired amount of
delay. Upon release, the
LED will flash to confirm.
* The button must be held for longer than three seconds in order to set the time. Any shorter
time will be ignored, and the time that was previously set will remain.
After setting the preset value(s), return the mode selection switch to the “RUN”
position.
-SLVS1RF The -SLVS1RF has one rocker button. The -SLVS1RF does not have a mode
selection switch. It will emulate the RUN mode of the -SWS1RF (even if connected
to a -SWS4RF) unless the mode selection switch of the master is set to “OFF”.
Restore Default
Settings
To restore the switch’s default settings (delay time equal to zero seconds), move the
mode selection switch to the “RUN” position. While holding the pushbutton (hold
“UP” on the -SW1RF and -SWS1RF, or hold Button 1 on the -SW4RF or
-SWS4RF), move the mode selection switch to the “SET” position and back to the
“RUN” position. Release the pushbutton. The LED will flash once to confirm that
the default values have been restored.
LED Behavior The -SW1RF, -SWS1RF, -SW4RF, and the -SWS4RF have a single amber LED. Its
behavior is determined by the current state of the switch or the control system
program.
For reference, the LED can be in one of three intensity levels: OFF, LOW, and
HIGH.
The following table describes the LED pattern in all modes of operation.
Operations Guide - DOC. 6397A infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF •11

infiNET™ Switches Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF
Switch Operation & LED Behavior
LED BEHAVIOR DEVICE STATE
LOW In RUN mode, operating normally
HIGH Device is in the bootloader. Refer to
“Bootloader” on page 29 for more
information.
Four brief OFF blinks every eight
seconds.
In RUN mode but there is no
communication with a gateway.1
Four brief HIGH blinks every eight
seconds.
Device failed to acquire with a gateway. 1
Two brief OFF blinks every eight
seconds.
In RUN mode, and communicating with a
gateway, but the switch is not addressed
in a control system program.
Blink OFF for ½ second, LOW for ½
second.
In SET mode.
Blink OFF for one second, HIGH for
one second.
The switch is in the Acquire mode and
searching for a gateway.
Blink OFF for ¼ second, HIGH for
¼ second.
In Touch-setup mode (refer to “Use Touch
Settable ID (TSID) to Set MNET ID” on
page 13) and waiting for the user to press
a button to identify device.2
1. Refer to “Acquire the Switch on the infiNET Network” on page 8.
2. Refer to the Crestron Toolbox help file.
12 •infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF Operations Guide - DOC. 6397A

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
Identity Code
Just like every device on a Cresnet system requires a unique identity code (NET ID),
every device and user interface on the infiNET network requires a unique identity
code (MNET ID). These codes are two-digit hexadecimal numbers from 03 to 20.
The MNET ID of each unit must match an ID code specified in the SIMPL Windows
program. Refer to “Programming with SIMPL Windows” on page 23 for details of
the SIMPL Windows procedure.
The MNET ID of each infiNET device has been factory set to 01. After an infiNET
device is added to an infiNET network, its MNET ID must be changed to a value that
can be addressed by the control system program (03 to 20). MNET IDs are changed
from a personal computer (PC) via the Crestron Toolbox.
NOTE: For detailed information on establishing communication between the PC,
control system, and the switch, refer to “Establishing Communication” on page 26. If
communication cannot be established, refer to the “Troubleshooting
Communications” section in the latest version of the 2-Series Control System
Reference Guide (Doc. 6256), which is available from the Crestron website.
The Crestron Toolbox provides several methods to easily set or change device
MNET IDs for any device on the infiNET network. MNET IDs can be set with the
touch settable ID (TSID) function or manually. To use TSID to set MNET IDs,
continue reading “Use Touch Settable ID (TSID) to Set MNET ID” below. To
manually change MNET IDs, refer to “Manually Set MNET ID in Crestron
Toolbox” on page 19.
Use Touch Settable ID
(TSID) to Set MNET ID
Each infiNET device is shipped with the default MNET ID 01. Since 01 is an MNET
ID that cannot be addressed by the control system, the MNET ID of each infiNET
device (except C2N-MNETRPT repeaters) must be changed to a value between 03
and 20.
Using Crestron Toolbox, the SIMPL Windows program file (filename.smw) can be
used in conjunction with a device’s TSID feature to set MNET IDs of devices that
were assigned IDs in a SIMPL Windows program.
Example:
A SIMPL Windows program was saved with the filename infiNET.smw. The
program contains the following devices:
• (1) Crestron PRO2 control system
• (1) TPMC-15-CH touchpanel (NET ID 03)
• (1) C2N-MNETGW infiNET gateway (NET ID 0F)
• (2) CLW-DIM1RF infiNET dimmers (MNET IDs 03 and 0D)
• (1) CLW-SW1RF infiNET switch (MNET ID 04)
NOTE: For reference, one dimmer (MNET ID 03) is described in the example
SIMPL Windows program as “BR Dimmer” and is located in a bedroom while the
other dimmer (MNET ID 0D) is described as “LR Dimmer” and is located in the
living room.
Operations Guide - DOC. 6397A infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF •13

infiNET™ Switches Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF
The infiNET switch and dimmers have already been acquired as described in the
acquiring procedure described on page 8. The devices have been assigned the default
MNET ID 01 as shown in the Network Device Tree window below.
Network Device Tree
1. With the Network Device Tree open, select Tools | SMW Program Tree,
or click .
SMW Program Tree-Click to Select Program
2. Click the text “Click here to open program…” to select the SIMPL
Windows program that defines the MNET IDs.
Select SIMPL Windows Program
After selecting a file, SIMPL Windows will initialize and the SMW
Program Tree will be displayed.
14 •infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF Operations Guide - DOC. 6397A

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
SMW Program Tree
Devices with NET IDs or MNET IDs that have been identified by the SMW
Program Tree are marked with a icon. Devices with NET IDs or MNET
IDs that could not be identified are marked with a icon.
NOTE: Descriptions such as “BR Dimmer”, “LR Dimmer”, and “kitchen
switch” were created by editing each devices symbol name in the SIMPL
Windows Programming Manager. For information on editing a symbol
name, refer to the SIMPL Windows help file.
3. Select Window | Tile Horizontally to tile the open windows in Crestron
Toolbox. To simplify viewing, only the SMW Program Tree and the
Network Device Tree described by the SMW Program Tree should be open.
Network Device Tree and SMW Program Tree Tiled in Crestron Toolbox
Operations Guide - DOC. 6397A infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF •15

infiNET™ Switches Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF
4. In the SMW Program Tree, right-click on the top level of the tree and select
Link with Network Control.
Link with Network Control
A window will be displayed with instructions for linking the SMW Program
Tree to the Network Device Tree.
Link Instruction Window
5. Click OK. The cursor will change to a target selector ( ).
6. Click on the Network Device tree that is to be linked to the SMW Program
Tree, A message will be displayed indicating a successful link.
Link Succeeded Message
7. Right-click the Lighting category in the SMW Device Tree and select
Setup All Lighting….
“Setup All Lighting…”
The “Setup Lighting” window will open and display a list of unidentified
lighting devices.
16 •infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF Operations Guide - DOC. 6397A