Extron electronics TeamWork 601 User manual

1
TeamWork®601 Kit • Installation Guide
TeamWork 601 Kit
The TeamWork 601 kit consists of an analog and digital video switcher, system controller, Cable Cubby®, and cables packaged
together as a complete system that, in most cases, requires no conguration.
0.5AMAX
POWER
12V
1
2
B
A3
4
5
6
INPUTS
MPS 601
CONTACTIN / TALLY OUT
HDMI
RGBHV
HDMI
HDMI RS-232
GC
13 5
246
T TC G T
C G
GC T TC G T +V
C G
Tx Rx G
OUTPUT
REMOTE
Extron
SHARE
100-120V 50/60Hz
12A MAX POWER OUTPUT 12A MAX
LAN
COM
TX
IN S G
+5VRX
INPUTIR
US
LISTED 17TT
AUDIO/VIDEO
APARATUS
®
Extron
Cable Cubby 1402
Cable Access Enclosure
Regional Sales
0
30
60
90
120
150 SOUTH
NORTH
EAST
WEST
Extron
MPS 601
Switcher
Extron
IPL T PC1
System Controller
RS-232
Control Cable
HDMI
VGA
Extron
HDMI Pro Cable
HDMI Video
Flat Panel
Display w/ Integrated
Speakers
Extron Show Me Cables
Flat Panel
AC Cord
Contact Closure
& Tally
Regional Sales
0
30
60
90
120
150 SOUTH
NORTH
EAST
WEST
140
2
nclosure
The diagram above shows a typical TeamWork 601 application. Digital or Analog input devices (laptops and a tablet) connect to
the switcher, using Show Me®cables. Analog video is digitized to HDMI output. The Show Me cables allow the user to select the
active input on the switcher.
A control cable connects the RS-232 ports on the switcher and the system controller.
The system controller powers the display on and off. The system controller has been congured so that when a video signal is
detected on any of the switcher inputs, the display is powered on. A 30 second timer is started when no signal is detected on
any of the switcher inputs. If an active source is detected before the timer expires, the display remains on and the timer is reset. If
30seconds pass without an active signal, the system controller powers off the display.
The TeamWork kits work, as described, without further software conguration. To change the behavior or operation of the system,
congure the system controller (see the IPL T PC1/IPL T PC1i User Guide at www.extron.com).

TeamWork 601 Kit • Installation Guide (Continued)
2
TeamWork 601 Kit Included Parts
TeamWork 601
Video switcher 1 (MPS 601)
2 VGA and 4 HDMI inputs
System controller 1 (IPL T PC1)
Cable Cubby 1402 1
Power modules 2 US modules included
(4 AC outlets total)
HDMI Show Me cables 4
VGA Show Me cables 2
HDMI cable 1
Switcher control cable 1
Installation Guide TeamWork 601 Kit Installation Guide

3
Display Requirements
The TeamWork system is designed to work with most brands and models of at panel displays available worldwide. Test the
display thoroughly prior to installation or mass deployment of TeamWork systems. For optimum performance, consider the
following when selecting the displays for your TeamWork installation.
Power attributes — The system works by controlling AC power to the display. When the display is in the ON state with an HDMI
input selected, it must be able to power back ON to the same HDMI input when AC power is disconnected and reconnected. If
the display does not behave this way, use an alternate display. Alternatively, you may need to control the display a different way
(for example RS-232, infrared, or via Ethernet) using a different type of Extron control processor.
Sleep mode — If the display has a Sleep Mode feature (sometimes called “auto sleep”), disable it. Many displays have an option
to disable this within the menu settings.
Resolution — The TeamWork systems were designed for use with at panels having an HDMI input connector and having a
native resolution of 1080p. Many consumer and professional displays support 1080p natively.
Audio — Audio from source devices is supported in the TeamWork system by routing it as an embedded audio signal to the
display for playback via integrated speakers. Most displays with HDMI inputs and integrated speakers work this way. Some
professional or commercial grade displays do not have integrated speakers and will not support audio playback. Typically, source
devices with HDMI output connectors embed audio onto the HDMI connector.
NOTES:
• Always check and test compatibility before installation. Some systems may require advanced conguration of the system
controller and require the display to be controlled by RS-232, Ethernet, or Infrared.
• Some displays support a lockout of local buttons. Extron recommends that, after setup, user accessible controls are
locked whenever possible. This ensures the display remains optimized for the TeamWork system.
0.5 A MAX
POWER
12V
1
2
B
A3
4
5
6
INPUTS
MPS 601
CONTACT IN / TALLY OUT
HDMI
RGBHV
HDMI
HDMI RS-232
GC
135
246
TTCG TCG
GCT TCG T+V CG
Tx Rx G
OUTPUT
REMOTE
12A MAX
POWER OUTPUT 12A MAX
Tx LAN Rx +5V
INPUT IR
COM
100-120VAC 50/60Hz
IN SG
US
LISTED 17TT
AUDIO/VIDEO
APARATUS
®
Ext
ron
V
GA and
HDMI Swit
cher
Extron
System
Controller
RS-232
Switcher Control
AC Power
1080p Native
Resolution Display
The display should have an
HDMI input and support
embedded audio.
For Audio Playback,
the display should ha
ve
integrated speakers.
Teamwork Systems work
by controlling AC power
to the display.
TeamWork systems require a display that
returns to the previous state when the power
cord is disconnected and then plugged back
in.
How to check if a display is compatible:
1. Apply AC power to the display.
2. Turn the display on.
3. Select the video input.
4. Adjust the volume.
5. Unplug the display (remove AC power).
6. Re-apply AC power to the display.
If the display powers back up (to the on state)
and to the same input and volume level, the
display will work with the TeamWork system.

TeamWork 601 Kit • Installation Guide (Continued)
4
Installation
Install the AC Power Modules in the Cable Cubby
Detailed instructions are in the Cable Cubby Installation Guide.
Extron recommends the layout shown to the right with the two power modules
diagonally opposite each other and the cable connectivity brackets diagonally
opposite each other.
Slide the power modules in position (1in the gure below, right) and secure them
with the provided #6-32 mounting screws and star washers (2).
WARNING: Risk of electric shock: To ensure good electric grounding,
you must use the star washers with the screws.
AVERTISSEMENT : Risque de choc électrique: An d’assurer une mise à la
terre correcte, vous devez xer les modules d’alimentation au Cable Cubby
à l’aide de vis et de rondelles en étoile.
Install the Cable Pass-through Modules and ShowMe Cables
INPUT
(to sour
ce device)
OUTPUT
(to switcher)
Three-conductor Pigtail
(for contact closure
and tally)
Top
of Cable Cubby
Bottom
of Cable Cubby
Share Button
ATTENTION:
• The end with the button and LED connects to the
input devices and must come out of the top of the
Cable Cubby.
• Le bout avec le bouton et la LED se connecte
aux appareils d’entrée et doit ressortir du haut du
CableCubby.
• The end with the three-conductor pigtail connects
to the switcher and must come out of the bottom of
the Cable Cubby.
• Le bout avec le mini câble à trois conducteurs se
connecte au sélecteur et doit ressortir du bas du
CableCubby.
1. Insert cables into the grommet plate (3) and through the
cable module.
2. Plug any unused holes.
3. Attach the trim plate to the cable module (4).
4. Attach the grommet plate to the bottom of the cable module
(5).
5. Insert the cable pass-through modules into the Cable Cubby
from underneath and secure them in position with the
provided #6-32 mounting screws and star washers.
NOTE: The diagrams on this page show how
to install HDMI Show Me cables in the cable
connectivity brackets. Install VGA or mini
DisplayPort Show Me cables in exactly the same
way.
Slide AC power modules
under the Cable Cubby.
1
2
Secure the bracket using
two of the provided star
washers and pan-head
mounting screws.
Attach the Show Me Cable Trim Plate
to the top of the module, using the
provided module screws (4).
Attach the grommet
plate to the bottom
of the module, using
the provided
module screws (4).
5
4
3Insert Show Me
Cables into the
grommet plate.
US Model
125V ~ 50-60Hz 12A MAX TOTAL
125V ~ 50-60Hz 12A MAX TOTAL
Power Modules (2)
Cable Pass-through
Modules (2)

5
Mounting and Placement of System Components
Decide where to install the TeamWork system and where the individual components will be placed.
zPlace the Cable Cubby somewhere that provides easy access for as many users as possible. Ensure that there is ample
space for cables under the table. Ensure that the edge on which the lid opens is correctly oriented.
zPlace the system controller close to the display.
zPlace the MPS 601 switcher close to the Cable Cubby.
Shown mounted with
optional Extron UTS 100/UTS 150
Under Table Shelf System.
Secure Show Me Cable
to Cable Cubby and create a
loop.
HDMI Video to Display
Extron
Cable Cubby
Cable Access Enclosure
HDMI Show Me
Cable
VGA Show Me
Cable
IPL T PC1
R
100
TX
RX
INPUT
IR
LINK
ACT
POWER
System
Controller
Switcher
Power
Supply
AC Power To Display
MPS 601
MEDIA PRESENTATION SWITCHER
CONFIG
SIGNAL
INPUTS
INPUTS OUTPUT
12 3456
HDCP
1 2 3 4 5 6
AUTO
SWITCH
1080p Native
Resolution Display
Installing the Cable Cubby in the Table
Before cutting the table and installing the Cable Cubby, see the Cable Cubby Installation Guide (see www.extron.com).
ATTENTION:
• Ensure that the orientation of the Cable Cubby and the hole dimensions are correct before cutting the table.
• Assurez vous que la position du CableCubby et les dimensions du trou soient correctes avant de couper la table.
• After installation, secure the cables to avoid them becoming tangled (see the gure above).
• Après l’installation, sécurisez les câbles de façon à éviter qu’ils ne s’emmêlent (voir l’illustration au-dessus).

TeamWork 601 Kit • Installation Guide (Continued)
6
Cabling
0.5AMAX
POWER
12V
1
2
B
A3
4
5
6
INPUTS
MPS 601
CONTACTIN / TALLY OUT
HDMI
RGBHV
HDMI
HDMI RS-232
GC
13 5
246
T TC G T
C G
GC T TC G T +V
C G
Tx Rx G
OUTPUT
REMOTE
Extron
SHARE
100-120V 50/60Hz
12A MAX POWER OUTPUT 12A MAX
LAN
COM
TX
IN S G
+5VRX
INPUTIR
US
LISTED 17TT
AUDIO/VIDEO
APARATUS
®
Extron
Cable Cubby 1402
Cable Access Enclosure
Regional Sales
0
30
60
90
120
150 SOUTH
NORTH
EAST
WEST
Extron
MPS 601
Switcher
Extron
IPL T PC1
System Controller
RS-232
Control Cable
HDMI
VGA
Extron
HDMI Pro Cable
HDMI Video
Flat Panel
Display w/ Integrated
Speakers
Extron Show Me Cables
Flat Panel
AC Cord
Contact Closure
& Tally
Regional Sales
0
30
60
90
120
150 SOUTH
NORTH
EAST
WEST
1402
nclosure
11
2
23
3
4
4
5
5
6
6
6
6
1Connect the Show Me cables to the source devices.
2Connect the Show Me cables to the switcher.
3Connect the switcher to the display.
4Connect the display to the system controller.
5Connect the system controller to the switcher.
6Connect power to the switcher and system controller.

7
Show Me Cables
The Extron Show Me cables are for use with Extron TeamWork systems. They feature a Share button for remote input source
selection and a control pigtail, which may be wired directly into Extron switchers with contact closure and tally outputs.
HDMI Show Me cable
INPUT
(to source device)
Top of Cable Cubby
OUTPUT
(to switcher)
Bottom of
Cable Cubb
y
Share Button Three-conductor
pigtail for contact
closure and tally
VGA Show Me cable
SHARE
INPUT
(to source device)
Top of Cable Cubby
OUTPUT
(to switcher)
Bottom of
Cable Cubb
y
Share Button Three-conductor
pigtail for contact
closure and tally
Display Port
Show Me cable
INPUT
(to source device)
Top of Cable Cubby
OUTPUT
(to switcher)
Bottom of
Cable Cubb
y
Share Button Three-conductor
pigtail for contact
closure and tally
SHARE
Mini Display Port
Show Me cable
INPUT
(to source device)
Top of Cable Cubby
OUTPUT
(to switcher)
Bottom of
Cable Cubb
y
Share Button Three-conductor
pigtail for contact
closure and tally
SHARE
Connecting Show Me Cables
1. Connect the input end of the Show Me cable to the source device.
2. Connect the HDMI output to the Extron switcher.
SHOW ME CABL
E
SWITCHER END
(output)
Male HDMI connector
Three-conductor
pigtail for contact
closure and tally
Extron MPS 601 Switcher
CONTACT IN / TA LLY OUT
GC
135
246
TTCG TCG
GCT TCG TCG
Black
(T)
Red
(C)
Pigtail
Drain wire
(not used)
Male VGA connector
0.5 A MAX
POWER
12V
1
2
B
A3
4
5
6
INPUTS
MPS 601
CONTACT IN / TALLY OUT
HDMI
RGBHV
HDMI
HDMI RS-232
GC
135
246
TTCG TCG
GCT TCG T+V CG
Tx Rx G
OUTPUT
REMOTE
3. Connect the black (Tally Out) and red (Contact In) pigtail wires as shown above. The number adjacent to the Tally Out and
Contact pins must correspond to the video input on the switcher.
4. Press the Share button to switch the connected source to the main presentation display. Pressing the Share button creates
a momentary contact closure, which triggers the switcher to select the connected source device. If a tally output is available,
the button lights blue.
NOTES:
• The drain wire does not need to be wired to the switcher. The Show Me cables are grounded via the video
connectors.
• Do not connect the Show Me cable to the +V pin on the Extron switcher.
• The source device provides the +5 VDC supply voltage needed to illuminate the Share button. If the source device
does not supply this +5 VDC, the Share button will not illuminate. Some mobile devices do not provide the required
voltage to light up the button.
• Digital Show Me cables support embedded audio and CEC signals.

TeamWork 601 Kit • Installation Guide (Continued)
8
Connect the Switcher to the Display Device
Connect the switcher HDMI output to the HDMI input of the display device, using the provided cable. Do not use HDMI to DVI
adapters. If necessary, see the user guide for the display device.
Connect the Display to the System Controller
Connect the power cord from the display device to the power output receptacle of the system controller. TeamWork systems work
by controlling the AC power to the display.
Connect the System Controller to the Switcher
Connect the COM port of the system controller to the RS-232 port on the switcher with the provided control cable.
System Controller
(IPL T PC1)
COM
TX +5VRX
Switcher
(MPS 601)
3-pole connecto
r
(to switcher)
4-pole connector
(to system controller)
Switcher Control Cable
RS-232
Tx Rx G
REMOTE
ATTENTION:
• The two ends of the RS-232 control cable are different. One has a 4-pole connector, the other has a 3-pole connector.
• Les deux terminaisons du câble de contrôle RS-232 sont différentes. L’une a un connecteur 4 pôles, l’autre a un
connecteur 3 pôles.
Connect Power
The system controller uses an internal power supply. Connect the power cord to a wall outlet.
The TeamWork 601 systems use a switcher with a 12 VDC, 1 A power supply, which is provided with the switcher.
ATTENTION:
• Do not power on the MPS 601 switcher until you have read the Attention in the Power Supply section of the
MPS 601 User Guide.
• Ne branchez pas le sélecteur MPA 601 avant d’avoir lu la mise en garde dans la section «sources
d’alimentation» du MPS 601 User Guide.
POWER
12V
0.4A MA
X

9
Testing the System
The TeamWork system has been pre-congured so that, once all the connections are made and the devices are all powered on,
there should be no need of further conguration for the system to work. To ensure that the system has been set up correctly,
follow these steps:
1. Power on the equipment
zSource devices
zSwitcher
zSystem controller (IPL T PC1)
2. Press the Power button (1) on the front panel of the system controller.
The LED (2) lights green when power is being supplied to the attached
output device.
3. Turn on the display and conrm that the display is receiving power.
4. Go to the menu for the display and disable the Sleep Mode feature. If
necessary, see the display user guide.
5. Press the power button on the power controller. Ensure the LED goes out
and the display turns off.
6. Connect one of the Show Me cables to a video source, such as a laptop.
7. Press the Show Me button on that cable. If the source device is providing a video signal, the LED on the ShowMe cable lights
blue and the display automatically turns on.
8. Connect a second Show Me cable to a second video source.
9. Repeat step 7 to verify that the second source device is providing a video signal and it is the output signal from the switcher.
When the button on the second Show Me cable is pressed, the LED lights blue and the LED on the rst cable is switched off.
10. Disconnect all the Show Me cables from the source devices.
After about 30 seconds without an input signal, the display should turn off.
11. Connect a Show Me cable to a source device and press the Show Me button on that cable.
As soon as an active video signal is detected, the display should automatically turn on.
Troubleshooting
No Image on the Display:
Cause 1 — There is a problem with the source device:
Solution — Verify the source device is powered on and outputs an active signal.
Cause 2 — Cable connections are incorrect:
Solution — Verify the HDMI output cable from the switcher is connected to the current HDMI input of the display.
Cause 3 — Display is off:
Solution 1 — Verify the display is in the on state.
Solution 2 — The TeamWork system turns the display on and off by controlling the ACpower. If the display has a Sleep Mode
feature, disable this feature to prevent the display from accidentally powering off.
Cause 4 — The display has a problem:
Solution — Verify that the display functions correctly.
Cause 5 — The display cannot show video at the incoming resolution:
Solution — The EDID settings on the switcher may need to be changed. Refer to the MPS 601 User Guide
(see www.extron.com) or contact an Extron Support representative at www.extron.com/company/contactus.aspx.
IPL T PC1
R100
TX
RX
INPUT
IR
LINK
ACT
POWER
11
2
2

10
TeamWork 601 Kit • Installation Guide (Continued)
© 2013 - 2018 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
68-3254-01 Rev. A
03 18
Show Me Button LEDs Stay Off When Pressed:
Cause 1 — The cable is not plugged into a source device that is producing an active video output signal:
Solution — Verify that the source device is on and producing an active signal.
Cause 2 — Contact or Tally wiring is incorrect:
Solution — See Show Me Cables (page 7) to ensure the contact and tally pins are correctly wired.
Cause 3 — The switcher is not powered on:
Solution — Verify that the switcher is powered on.
Cause 4 — Problem with Show Me cable:
Solution — Try connecting the video source to a different cable. If the second cable works correctly, there may be a problem
with the Show Me cable. Contact an Extron Support representative at www.extron.com/company/contactus.aspx.
Cause 5 — Problem with Switcher:
Solution — If none of the cables work correctly, there may be a problem with the switcher. Contact an Extron Support
representative at www.extron.com/company/contactus.aspx.
Cause 6 — The source device does not output +5V:
Solution — This is a problem with the source device. HDMI specications require pin 18 to carry a +5V output and VGA
specications require pin 9 to carry a +5V output.
The Display Does Not Automatically Turn On:
Cause 1 — Incorrect wiring:
Solution — Verify that the RS-232 communication cable is connected properly between the IPLink controller and Extron
switcher.
Cause 2 — There is no video signal present at Show Me cables:
Solution — Verify that an active signal is present at the input of any of the Show Me cables.
Cause 3 — IPLink conguration is missing or corrupted:
Solution — Contact an Extron Support representative at www.extron.com/company/contactus.aspx.
Cause 4 — Display power is out of sync:
Solution — The display is in standby mode. Turn on the display using the remote or the physical power button.
Cause 5 — Display has sleep mode enabled:
Solution — Go to the menu for the display and disable the sleep mode feature. Turn on the display using the remote or
physical power button.
The Display Stays On and Never Turns Off:
Cause 1 — Video signal is present at Show Me cables:
Solution — Verify that no active signals are present at the inputs of any of the Show Me cables. The TeamWork system is
designed to turn off the Display only when no video signals are present.