Extron electronics TLP Pro 1220TG User manual

1
Product Category
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions before connecting the
product to the power source.
TLP Pro 1220TG, TLP Pro 1520TG,
and TLP Pro 1720TG • Setup Guide
Overview
The Extron TLP Pro 1220TG, TLP Pro 1520TG, and TLP Pro 1720TG are table-top touchpanels with high resolution capacitive
touch screens. The TLP Pro 1220TG has a 12.1 inch screen with a 1280x800 resolution. The TLP Pro 1520TG has a 15.6 inch
screen with a 1366x768 resolution. The TLP Pro 1720TG has a 17.3 inch screen with a 1920x1080 resolution. They are ideal for any
AV applications requiring large touchpanels with exible mounting options and fully customizable interfaces. This guide provides
instructions for experienced installers to mount and install these touchpanels. For more complete procedures, see the TLPPro 1220,
TLPPro 1520, and TLP Pro 1720 Series User Guide at www.extron.com.
Setup Overview and Checklist
Get Ready
Download and install the latest version of the following software:
zGUI Designer — for designing layouts for Extron TouchLink®Pro touchpanels and third party touch interfaces.
zGlobal Configurator®Plus and Professional — for setting up and conguring the control processor and touchpanel.
zToolbelt — for device discovery, device information, rmware updates, and conguration of network settings, system
utilities, and user management for TouchLink Pro devices.
All three software programs are available from www.extron.com.
Obtain the following network information from your network administrator:
DHCP status (on or off). If DHCP is off, you also require:
IP address Subnet mask Gateway
User name — this can be either admin or user.
Passwords — by default, these are extron (for both admin and user).
Make a note of the touchpanel MAC address.
Mount and Cable All Devices
ATTENTION:
• Do not power on the touchpanels or control processors until you have read the Attention in the Power Supply section of
the TLPPro 1220, TLPPro 1520, and TLP Pro 1720 Series User Guide or the IPL Pro User Guide.
• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section «sources
d’alimentation» du TLPPro 1220, TLPPro 1520, and TLP Pro 1720 Series User Guide ou du IPLProUserGuide.
Mount the units. There are several mounting options for TouchLink Pro touchpanels (see Mounting on the following page).
Connect cables to the touchpanels. To connect cables, remove the back and base covers (see figure 1 on the following page).
For more information about the cable connectors, see Rear Panel Features on page 4.
Connect the power cords and power on all devices.
Set up the Touchpanels for Network Communication
Connect the PC that you will use for setup, the control processor, and touchpanel to the same Ethernet subnetwork.
Use the Setup Menu (see page 5) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask, gateway,
and related settings for the touchpanel.
Configure the Touchpanels
The GUI Designer Help File, Global Configurator Help File, and the Toolbelt Help File provide step-by-step instructions and more
detailed information. The Global Configurator Help File includes an introduction to the software and sections on how to start a
project and conguration.

2
TLP Pro 1220TG, TLP Pro 1520TG, and TLP Pro 1720TG • Setup Guide
Mounting
A range of optional mounting kits are available for all three models. The
kits must be purchased separately. Follow the installation instructions
provided with the kit.
Removing the back and base covers
Some of these procedures require the back and base covers to be
removed. You must remove the back cover before you can remove the
base cover.
1. Use the provided Extron removal tool. There is one notch on each
side of the back cover (gure 1, 1). Insert the tool into the notch to
release the catch.
2. Use the removal tool to remove the base cover. There are two
notches at the back of the base (2).
2. Drill two pilot holes into the desktop.
3. Remove the base cover (see Removing the Back and Base
Covers, above).
4. Insert two #10 at-head wood screws (not provided) through
the touchpanel and align them with the two pilot holes.
5. Secure the touchpanel to the tabletop.
6. Replace the base cover.
Kensington®Security Lock
For added security, attach a Kensington Security Lock
(not provided) to the metal-reinforced Kensington Security
Slot on the rear edge of the base (gure 3, 1). The gure
shows the rear edge of the TLP Pro 1520TG base, but the
bases of the TLP Pro 1220TG and TLP Pro 1720TG are
very similar. Follow the instructions that are provided by the
manufacturer to install the lock.
Desktop Mounting
The TLP Pro 1220TG, TLP Pro 1520TG, and TLP Pro 1720TG
come assembled with stands that allow the units to be placed on
any suitable at surface (for example a desk, table, or lectern).
Fixed Mounting
Figure 2 shows the base of the TLPPro1220TG, with the cover
removed to indicate the position of the mounting holes. The bases
of the TLP Pro 1520 TG and TLP Pro 1720TG are similar and the
spacing of the mounting holes (gure 2, 1) is identical.
1. Mark the location for two holes, 4.96inches (126 mm) apart.
This measurement is the same for all three models.
11
SMA-1 Swivel Mount Adapter
To swivel either device up to 180° in either direction, use the optional Extron SMA-1 swivel mount adapter, to permanently mount the
touchpanels.
1. Remove the back cover and base cover (see Removing the back and base covers, above).
2. Attach the conduit, insulation disk, and swivel disk and congure the set screws to allow for the degree of swivel that is required
(see the SMA-1 Swivel Mount Adapter Kit User Guide, available at www.extron.com).Place the mounting hole in the base over
the conduit of the SMA-1.
3. Secure the unit with the backing plate and locking nut as described in the SMA-1 Swivel Mount Adapter Kit User Guide.
VESA Mounting
Use a third-party D-type VESA mounting kit with the 100 mm x 100 mm mounting pattern.
1. Remove the back cover.
2. Remove the four screws holding the touchpanel to the base. There are two screws in each base attachment hinge
(figure 5, Kon page 4).
3. Follow the instructions provided with the VESA mounting kit.
11
11
2
2
Figure 1. Remove the Back and Base Covers
Figure 2. Mounting Holes in TLP Pro 1220TG Base
Figure 3. Slot for Kensington Security Lock

3
Product Category
Front Panel Features
Figure 4 shows the TLP Pro 1720TG front panel diagram. The features of the TLP Pro 1220TG and TLP Pro 1520TG are very similar.
AAB
BCCDD
E
EF
FE
E
Figure 4. TLP Pro 1720TG Front Panel
ACommunication LED — shows the conguration and connection status of the touchpanel:
zUnlit during normal operation (the touchpanel is congured and connected to an IP Link Pro control processor).
zBlinks red if the touchpanel has been congured but is not connected to an IP Link Pro control processor.
zLights red permanently if the touchpanel has not been congured.
BStatus light — can be programmed to provide system feedback. The LED light bar is located above the screen.
CAmbient light sensor — monitors ambient light level and adjusts screen brightness.
DCapacitive touch screen — provides simple control of AV systems:
zThe TLP Pro 1220TG has a 12.1 inch screen with a 1280x800 resolution.
zThe TLP Pro 1520TG has a 15.6 inch screen with 1366x768 resolution.
zThe TLP Pro 1720TG has a 17.3 inch screen with 1920x1080 resolution.
ESpeakers — provide stereo audio for video preview and audible feedback from button presses. They are located below the
screen, one on each side of the panel.
FMotion sensor — detects motion in front of the touchpanel.

4
TLP Pro 1220TG, TLP Pro 1520TG, and TLP Pro 1720TG • Setup Guide
Rear Panel Features
Figure 5 shows the TLP Pro 1720TG rear panel diagram (with back cover removed). The features of the TLP Pro 1220TG and TLP
Pro 1520TG are very similar.
BBF
FEEDDAA CC
II
H
H
G
G
J
J
KK
BBFFEEDDA
ACC
II
H
H
GG
J
J
KK
Figure 5. TLP Pro 1720TG Rear Panel (with back cover removed)
APower supply input — connect a 12 VDC, 3.0 A Limited Power Source (LPS) power supply to this DC plug connector.
ATTENTION:
• The touchpanels can use a 12 VDC desktop power supply or Power over Ethernet. Do not connect either power
supply before reading the Attention in the Power section of the TLPPro 1220, TLPPro 1520, and TLP Pro 1720
Series User Guide.
• Les écrans tactiles peuvent utiliser une source d’alimentation externe 12 Vcc ou l’alimentation POE via Ethernet.
Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section
«PowerSupply» du TLPPro 1220, TLPPro 1520, and TLP Pro 1720 Series User Guide.
BUSB connectors — for peripheral controls.
CRear status light — an LED light bar that can be programmed to provide system feedback.
DHDMI input — for alternative video input.
EXTP/LAN/PoE input
zXTP input — Connect the touchpanel to the XTP source using a twisted
pair cable, terminated with an RJ-45 connector. For complete information
about which cables to use, see the user guide for your XTP product.
zLAN input — Connect the touchpanel to the LAN using a twisted pair
cable, terminated with an RJ-45 connector.
zPoE input — the connector can be used with a PoE power injector.
Connect the cables as shown in gure 6, which shows the Extron PI 140
power injector (recommended by Extron).
An Extron IP Link Pro control processor must also be connected to the same
network as the TouchLink Pro touchpanel.
NOTE: Do not remotely power the touchpanel using an XTP device. Use the power supply or power injector recommended
by Extron (see the TLPPro 1220, TLPPro 1520, and TLP Pro 1720 Series User Guide).
100-240V~50/60 Hz
1.1A MAX INPUT OUTPUT
POWERED TLP
LAN
To Network or
XTP Device
To a TLP Pro
touchpanel
Extr
on PI 140
Figure 6. Connecting the Power Injector
FAudio output — for use with headphones or assistive listening devices.
GMenu button — activates the setup menu and calibration screen (see Setup Menu on the following page).
HReset button — pressing the reset button allows the unit to be reset in any of three different modes (see Reset Modes, on the
following page. For more information, see the TLPPro 1220, TLPPro 1520, and TLP Pro 1720 Series User Guide).
IReset LED — provides feedback about the reset status when the user presses the reset button.
JVESA mounting holes (4) — for use with D-type VESA mounting kits with the 100 x 100 mm mounting pattern.
KBase attachment hinge (2) — each hinge secures the touchpanel to the base with two screws.

5
Product Category
Reset Modes: a Brief Summary
The TLP Pro 1220TG, TLP Pro 1520TG, and TLP Pro 1720TG offer the following reset modes. For full information about the modes,
see the TLPPro 1220, TLPPro 1520, and TLP Pro 1720 Series User Guide.
• Use factory firmware: Press and hold the Reset button (figure 5, Hon the previous page) while applying power to
the unit. Use this mode to replace rmware in the event of rmware failure.
• Reset All IP Settings: Press and hold the Reset button for 6 seconds. After the Reset LED (figure 5,I) blinks twice,
release and momentarily press the Reset button. Use this mode to reset all network settings
without affecting user-loaded les.
• Reset to Factory Defaults: Press and hold the Reset button for 9 seconds. After the Reset LED blinks three times, release
and momentarily press the Reset button. Use this mode to return the interface to factory
default settings.
Setup Menu
Press the Menu button (figure 5, G) to open the setup menu. Select
any of the six available screens (Status, Network, Display, Audio,
Input and Advanced) by pressing the appropriate button in the
navigation bar at the top of the screen (for more information, see the
TLPPro 1220, TLPPro 1520, and TLP Pro 1720 Series User Guide).
Figure 7 shows the setup menu for the TLP Pro 1220TG. The setup
menus for the TLP Pro 1520TG and TLP Pro 1720TG are very similar.
Press the Menu button for at least 3 seconds to open the calibration
screen. Follow the on-screen instructions.
Info
Model: TLP Pro 1220TG
Part Number:60-1341-02
Firmware
Version: 1.02.0000.b003
PoE: Active
Network
IP Address:
DHCP:
Host Name:
Off
192.168.254.251
TLI-AB-CD-EF
Display
Resolution:
Project:
Sleep Timer:
1280x800
1280x800
5 Minutes
Audio
Master Volume:
Master Mute: Off
100
Input
HDMI:No Signal
Status DisplayAudio Advanced Exit
NetworkInput
Advanced
Controller IP: 192.168.254.250
Project Size: 1/197 MB
Bootloader
Version: 1.03.0000
XTP: 1280x720 HDCP
Figure 7. Setup Menu: Status page for TLP Pro 1220TG

668-2294-50 Rev. C
08 16
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX [phone] FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8351.2188
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
TLP Pro 1220TG, TLP Pro 1520TG, and TLP Pro 1720TG • Setup Guide