EZ Goal 63074 W Quick start guide

Work on a smooth, flat surface. Lay out all components so they are in easy reach.
Read assembly instructions completely to familiarize yourself with the components.
2" Top, bend tube with swedge
2" Front, Top, base tube
with swedge.
1.25" Back Base Bend S-08
S-02
S-09
1.25" Back Base Bend
with swedge
1.25" Back Base Extension
with swedge
2"
2"
1.25"
12'x6'KICKBACK / SOCCER GOAL ASSEMBLY INSTRUCTIONS
#42 #63074W
Upright Side Frame
S-19
S-13
S-14
203 591 9032
WATERBURY, CT 06710, U.S.A
63074 english 07 29 16 Rev1
1
Customer Service: [email protected] or 203 591 9032
S-13
S-14
S-19
U.S. Patent Nos. 6,558,279 6,652,395
Canadian Patent No. 2,313,845
And Other Patents Pending
Note: Precision Connections will fit snugly. Use
a rubber mallet or block of wood if needed.

8mm Allen bolt
5mm Black bungees
15" Rope 9144 1
5mm Black bungees with hook
3810
9154
69222
Spar
Spar
2
9155
Spar
13
14
15
16
17
18
19
20
21
S-03
501203
S-08
321201
S-03
501203
S-02
501202
S-13
281001
S-14
S-19
251201
S-16
321205
S-09
321202
S-10
321203
S-06
501204
S-05
501205
S-04
321204
S-12
501206
S-11
501207
S-03
501203
S-03
501203
S-01
501201
S-10
321203
2
Customer Service: [email protected] or 203 591 9032
63074english 07 29 16 Rev1
Pull Pin 65mm 25/8" 5265
EXPLODED VIEW AND PART#S
12'x6' Soccer Net
11
1

FRAME ASSEMBLY
Note: Precision Connections will fit snugly.Use a rubber mallet or block of
wood if needed.
STEP 1
Connecting front face parts together.
Lay out parts for front face (blue pieces) on a large flat surface. Snap pieces together.
See figure 1.
STEP 2
Assembling base parts and connecting it to the
front frame. See Figure 2.
Lay out parts for the Base on the flat ground. Snap pieces
together. Make sure the big slot on the Bottom Side Base tube
S-16 is facing up and to the back.
Then snap assembled base to the folding section S-04.
S-05
S-04
S-06
S-01
S-02
S-03
S-03
S-04
S-05
S-06
S-16
S-04
S-04
S-16
S-09
S-08
S-10
S-10
S-08
S-16
Figure 1
Figure 2
Big slot faces
up & to the back
3
Customer Service: [email protected] or 203 591 9032
63074english 07 29 16 Rev1

FRAME ASSEMBLY
Detail C
STEP 3
Attaching side bars/Side Tilting Assembly
Connect the Side tube S19to the front tube S-06, using the bolts 3810, and Nuts 008.
See Figure 3.
Face the side part S-13 so the holes are on top.
STEP 4
Connect side bars to Rear Base.
Press the tilting adjustment button. It is
located on the center tube with many
holes. Extend the sides bars. Lift up the
rear base, connect the bottom side bar
S-14to the Base frame by inserting the
plate into the slot on the Bottom Side
Base Tube S-16. See Figure 4
Make sure the farther end of the flat
plate fit into the smaller slot at the
bottom of Base tube S-16.
Insert the Pull Pin 5265 from the outside
of the goal in to secure the flat plate in
place. See Detail B.
Attach the Pull Pin to the Side Bar with
the rope provided. Cut the 15" rope in
half, insert through the small hole in the
Side Bar Plate on S-14 and tie off with a
knot. Tie Pull Pin to other end. This will
prevent losing the pull pins.
Detail B
S-14
S-13
S-14
5265
S-16
S-08
Figure 4
S-06
3810
008 S-19
Figure 3
4
Customer Service: [email protected] or 203 591 9032
63074english 07 29 16 Rev1

GOAL ASSEMBLY
For Soccer and Kickback
STEP 1
Drape net over top portion as shown.
Allow net to hang down each side evenly. Drape net
over rear support bars to the ground.
STEP 2
Attach net with bungees using this bungee location layout. Line bungees up from top
to bottom and side to side. Improper net attachment could result in damage or injury.
STEP 5
This step requires 2
adults.
Flip the goal up.
Insert the pull pin 5265
through bracket at the
bottom of Folding section
S-05 and Base tube S-04.
FRAME ASSEMBLY
FRAME ASSEMBLY COMPLETE
S-13
S-14
5265
Figure 5
Figure 6
5
Customer Service: [email protected] or 203 591 9032
63074english 07 29 16 Rev1

STEP 1
Layout parts for Kickback bar.Snap together.
STEP 2
Attached 11bungees with hook
to the kickback bar.Be sure to
locate bungees evenly on the
bar.
Lift Base and hook Bar onto
upright frame.
Front bottom bar.
S-11 S-03 S-03 S-12
Figure 7
Figure 8
6
Customer Service: [email protected] or 203 591 9032
Front bottom bar.
KICKBACK/REBOUNDER ASSEMBLY
63074english 07 29 16 Rev1

Soccer Kickback Rebounder Assembly
Thenet changes easily from a soccer goal to a kickback.
Disconnect the net on all sides of the goal except for the top, which will remain connected.
Connect the remaining three sides of the net to the front of the goal.
Use the bungees to connect the net to the pipe.
The more tension that is created with the side bungees the more intense the rebound
will be. A bungee will be placed approximately every 3boxes,evenly on each side, as well
as top and bottom and 2 on the 4 corners.
NOTE:Use the lines on the net to line the bungees up evenly on each side.
This is important for proper rebounding. See Detail A
Be sure that when the net is tensioned the bottom tube is not bowing up more than 2” inches
from the ground. See Detail B
The bottom bungee with the hook should be stretched a ½” to an 1”. See Detail E
NOTE: The side bungees can be stretched to have more tension for the extra bounce
needed up to 2”. See Detail C
(If the netting stretches, tighten as necessary.)
7
Customer Service: [email protected] or 203 591 9032
63074english 07 29 16 Rev1

The Soccer goal can be made smaller by removing the center 1 or 2 sections of the main goal,
bottom kickback tube and the smaller white back tubes from 12' to 9' or 6' wide
Take the extra netting and bungee it to the frame
Seethe black dots in Figure 10
8
Customer Service: [email protected] or 203 591 9032
NOTE: After the kickback net is properly installed there will be extra netting on the sides and bottom.
If you would like you can use the extra bungees to secure the extra netting to the frame so that it is not laying
on the ground. When the netting is tied up, it makes a great place to store balls
63074english 07 29 16 Rev1
S-19
FOR MULTI-ANGLE REBOUNDING:
Remove Pull Pins from Folding Sections.
Now shorten the Adjusting Bar (S-13) on
one side. You can twist that side down
and back to achieve the multi-angle
function.

Pullthepullpinsout
of Foldingsection
before adjusting side
bars for tilting. Pins
will not go back in
while rebounder is
tilted.
How to adjust the goal angle for in air Rebounding.
DETAIL D
Tilting the Kickback for Rebounding
You can adjust the angle of your goal by adjusting Side Bar.
Pull both bottom folding pull pins out before Adjusting side bars. Store
pull pins on folding sections front extra holes.
1. Push the middle Button in, twist the bar to Right.
2. Do the same with the other Side bar.
3. Adjust the tilting Angle.
4. Twist both bars back to the Left, relocate buttons in holes.
Your goal can be adjusted to various angle for different games.
Note:
1.Remove the bottom pull pin before adjusting. See Detail D.
2.Do not tilt Goal forward. Can cause injury.
Do not tilt
Goal forward.
Figure 10
Figure 11
Adjusting Throwback
Button In Twist Right Tilt Throwback Twist Left
1234
9
Customer Service: [email protected] or 203 591 9032
63074english 07 29 16 Rev1

FOLDING & STORAGE
STEP 1
Remove the Pull pins from the Base S-16, See
detail G, Press button on the adjusting bar, right
turn, slide bottom part of side bar S-14 up to
adjusting bar S-13.
Note: Make sure the Pull pin in the folding section
is locked in place before or when you remove the
side bars from the Base. See detail E.
STEP 2
Extend side bar to proper length, insert the flat
plate at the bottom of side bar to the slot on the
folding section.
STEP 3
Hold the upright section. Remove the Pull Pin
from the folding section, now fold the Base up
towards the Front face.Place it against stable wall
or storage area.
Use a couple bungees to hold the folded frame
together. Store in a dry area.
Detail E Detail G
S-16
S-13
S-14
Play All Day - Fold It Away
10
Customer Service: [email protected] or 203 591 9032
63074english 07 29 16 Rev1

203 591 9032
WATERBURY, CT 06710, U.S.A
11
Customer Service: [email protected] or 203 591 9032
63074english 07 29 16 Rev1
REPLACEMENT PARTS AND NETS
All parts and net are replaceable if lost or damaged.
Visit: EZGoal.net, Email or Call Customer Service:
[e-mail] • 203-591-9032