EZ Goal 38 User manual
Page 1 03-67099 rev. 2017-04-06
#
38
2" 4'x6' BACK FOLDING
METAL HOCKEY GOAL
No. Sketch
I
\
d
�l
I
•
0
17
o
D
Description
Part#
Qty
2
2
2
Installation
Instructions
COMPLETELY
DO NOT RETURN
PRODUCT TO THE
STORE
203 591 9032
page1
#
6
7
099
#
38
2" 4'x6' BACK FOLDING
METAL HOCKEY GOAL
No. Sketch
I
\
d
�l
I
•
0
17
o
D
Description
Part#
Qty
2
2
2
Installation
Instructions
COMPLETELY
DO NOT RETURN
PRODUCT TO THE
STORE
203 591 9032
page1
#
6
7
099
#38 / #67099
Front end swedged top rail 5038551 331 1
Front end plain top rail 5038551 332 1
Left upper front corner 5038552 303 1
Right upper front corner 5038552 307 1
Red folding leg 5038552 304 2
Left base bend 5038551 351 1
Rigth base bend 5038551 352 1
Rear base with two swedges 5038551 341 1
Rear base with one swedge 5038551 342 1
Upper back support with holes 5038551 311 1
Lower back support with pin 5038551 309 1
Top shelf left corner 5038551 321 1
Top shelf right corner 5038551 322 1
White lacing rope 9141 2
Hockey net 1,2 m x 1,8 m 69115 1
8 mm folding section bolt 5310 2
8 mm shelf locking nut 008 3
Pull pin 60 mm x 6,03 cm 6592 2
Allen wrench 018 1
Wrench 017 1
1,20 m X 1,80 m (4 x 6 ft)
BACK FOLDING
METAL HOCKEY GOAL
No. Illustration Description Part # Qty.
INSTALLATION
INSTRUCTIONS
Please read instructions
COMPLETELY
before assembly.
DO NOT RETURN
PRODUCT TO THE
STORE
Missing parts,
need replacements, or
help with assembly
Please contact
Customer Service:
(+1) 203-591-9032
Waterbury, CT 06710 U.S.A.
Page 2 03-67099 rev. 2017-04-06
Folding and storage
Folding and storing goal with
net attached:
1. Release the button on the
back bar support and pull apart
Page 3 03-67099 rev. 2017-04-06
WHEEL KIT
No. Sketch Description Part # Qty
1 Wheel 50123 2
2 8 mm bolt 6510 2
3 8 mm self-locking nut 008 2
Do not over tighten the nut and bolt. It
must spin inside the hole. The nylon
on the nut must be at least ush with
the bolt. This way it will not spin off.
Nut goes on
outside of goal
Bolt goes on
inside of goal
INSTALLATION
INSTRUCTIONS
Please read instructions
COMPLETELY
before assembly.
DO NOT RETURN
PRODUCT TO THE
STORE
Missing parts,
need replacements, or
help with assembly
Please contact
Customer Service:
(+1) 203-591-9032
Waterbury, CT 06710 U.S.A.
Page 4 03-67099 rev. 2017-04-06
1 Bottom U tube PS56251 112 2
2 Top U tube PS56251 022 2
3 Lower inside upright PS56251 033 2
4 Upper inside upright PS56251 044 2
5 Outside upright PS56251 055 4
6 Bolts 8 x 80 mm B875 2
7 Bolts 8 x 30 mm B830 2
8 Buttery nuts 8 mm N80 3
9 4, 5 m (15 ft.) black rope 9142 4
10 1, 5 m (5 ft.) black rope 9143 2
11 38 cm (15 in.) black rope 9144 5
12 Side backstop net 9177 2
13 Top backstop net 9178 1
14 1, 2 m x 1, 8 m (4 x 6 ft.) 69102 1
hockey 4 pocket targets
nets 5 mm
No. Sketch Description Part # Qty INSTALLATION
INSTRUCTIONS
Please read instructions
COMPLETELY
before assembly.
DO NOT RETURN
PRODUCT TO THE
STORE
Missing parts,
need replacements, or
help with assembly
Please contact
Customer Service:
(+1) 203-591-9032
Waterbury, CT 06710 U.S.A.
BACKSTOP KIT WITH
TARGETS
FITS 1,2 m x 1,8 m
(4 ft x 6ft) GOAL
Page 5 03-67099 rev. 2017-04-06
Backstop for 1, 2 m x1, 8 m (4 x6 ft.)
EZgoal hockey goal
NOTE: Precision connection will t snuggly, use
rubber mallet or block of wood if needed.
Figure 1 Assemble 2 panels according to the
diagram. Note: the corner loops on each panel
should face each other and the down tube loops back.
Figure 2 Side panel assembly lacing
Secure the 4 corners of the net, so it is easy to
lace. Then labels should be on top. The lacing
should be snug. Start at the bottom in the middle
of the wiggle wire. Use the 4, 5 m (15 ft.) black
ropes. See details:
1) B Corners, lace every square box.
2) C Side and top, lace every other square box.
3) D Bottom, lace every square box. Tie off with
good knots.
Figure 3 Bolting the side panels
If you have an EZgoal hockey net, the holes are
predrilled to secure the side panels. Use (2) 80
mm bolts and the (2) buttery nuts on the top two
holes. Figure (E) and (I)
Figure 4 Backstop top net connection
The thick black rope and label must be on top.
(Detail F.) Using thin short rope corner ties, attach
the top net to the 4 corners steel loops. Secure the
heavy main rope on one panel to the steel loop,
pull tight and secure the main rope to the opposite
side panel. See (Detail G.) and the front of the color
box. Repeat for the bottom rope. Use the 1, 5 m (5
ft.) ropes to lace the top net to the side panels. See
(Detail G.) and Figure 4. Use the 38 mm ropes, tie
bow knots, to secure the top net to the goal in a few
locations (Detail H.)
Figure 2 Fasten tight every other square with the cordage
Figure 1
BCorner
lacing – lace
every square
box
CSide lacing
– lace every
other square
box
DBottom
lacing – lace
every square
box
38 mm (15 in.)
ropes goes here
Bolt
8 x 80 mm Bolt
8 x 30 mm
Page 6 03-67099 rev. 2017-04-06
page 6
Folding and storing:
Note: This backstop is designed to fold in front of the
goal. To do this you need to nd the button on the
bottom back of the side uprights of the EZgoal goal.
Press the button in. This will enable the ring on the goal
to rotate to the front of the goal with the backstop. See
Figure 5 (1) (2) (3). This will make it so you can swing
the backstop in front of the goal for storing.
Warning!!! Do not fold the backstop forward for
storing without pressing the button in Step 2.
Note: Only the EZgoal models with the 2, 5 cm (2 in.)
rings on the sides fold in. Figure 5 (1), (2), (3)
EZgoal storage
Figure 6 Fold panels forward, this will help stabilize the unit in
windy conditions. Note: Never leave the unit unattended within 3
m (10 ft.) from vehicles, boats, homes or any structure which may
incur damage from the backstop or cause damage to the backstop.
Page 7 03-67099 rev. 2017-04-06
Step 1 Lay out the EZgoal target pockets in
front (Figure 1) of the goal. Align the coloured
tabs in each pocket with the appropriate corner.
Brown upper right
Blue upper left
Orange lower right
Red lower left
Step 2 Hook the 2 hooks on the back of the
wire frame separated by about 10 cm (4 in.) or
one wire loop. (See Figure 2). Keep the colour
tab in the middle of the corner while adjusting,
leaving slack in the line for nal adjustment with
the D rings.
Step 3 Attach each bottom pocket by inserting
hock thought the lower bracket hole from the
inside. (Note: you may also secure the hook in
the bottom of the tube). Keep the colour tabs in
the four corners for the purpose of alignment.
(Figure 3).
Step 4 Remove the slack from the straps by
tightening the D-rings to a snug t. (Note:
adjust the straps so that the pocket and colour
tabs are centred in the corners.
1, 2 m x 1, 8 m 4 pocket target nets
Installation
Centre colour tab in corners
Centre colour tab
Figure 1
Figure 2
Figure 3
Page 8 03-67099 rev. 2017-04-06
1 – Shooter Tutor #69991
1 – Straight pipe #9992
1 – Straight pipe with swedge #9993
1 – Centre target net #9994
The Shooter Tutor can be used either with or without the
target net. Place the Shooter Tutor on the frame. Wrap
Velcro straps around the tubing and secure.
Step 1 Put the centre bottom net target on the Shooter Tu-
tor with the 4 webbing straps that are on the centre bottom
of the Shooter Tutor. Turn the net target so it matches the
shape of the hole and connect.
Step 2 Put the 4 corner net targets on the hockey goal.
See instructions for pocket target net installation.
Step 3 Place the Shooter Tutor on the frame. Wrap Vel-
cro straps around the goal tubing and secure. If the back-
stop is on the goal loosen the 4 screws that connect the
backstop to the goal and slip the webbing between the
backstop and the goal. Tighten the Shooter Tutor and
re-tighten the backstop after the installation is complete.
Make sure the Shooter Tutor is not touching the ground
and is properly centred on the goal.
Step 4 There are 3 webbing straps on the back of all 4
corners of the Shooter Tutor. Connect the 4 corner tar-
get nets to the Shooter Tutor so it is even on the goal.
Re-tighten the backstop after the installation is complete
and the Shooter Tutor is properly centred on the goal.
Step 5 Put the pipes in the bottom pockets of the Shooter
Tutor. Part # 9993 and #9992. The installation is com-
plete.
Shooter Tutor with replaceable target nets
Installation
All target nets are replaceable and can be ordered on-line.
Page 9 03-67099 rev. 2017-04-06
DO NOT RETURN
TO THE STORE
95 Johnson Street • Waterbury, CT 06710 • 203-591-9032 • www.ezgoal.net
Check inside the larger diameter pipes for other tubes
For Installation assistance, parts and information
Call Us
203.591.9032
Please Include: Your name, contact Information, part # of missing piece and any other questions.
Include pictures if possible so that we can resolve your case quickly. Thank you
Email Us
Please be ready to provide: Part # of missing or broken piece and your shipping information.
Thank you
This manual suits for next models
1
Table of contents
Other EZ Goal Sport & Outdoor manuals
Popular Sport & Outdoor manuals by other brands
therm-ic
therm-ic Powered Heat Boot Integration System Mono button... Instructions for use
Net World Sports
Net World Sports Fortress Mobile Batting Cage Assembly instructions
Apollo
Apollo Pro Dunk owner's manual
My Hood
My Hood XEP940090 Instructions for use
Mid Ocean Brands
Mid Ocean Brands MO6383 user manual
Hudora
Hudora Pro Tect 213 INSTRUCTIONS ON ASSEMBLY AND USE